New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Shop storage update

Posts

Shop storage update

#1

Shop storage update

Derek Cohen (in Perth, Australia)

I do not post much about my workshop, mainly because it is rubbish compared with many examples I have seen on this forum. While I admire and aspire to a shop with beautifully fitted cabinets, ones that would not look out of place in my kitchen, the thought of all that beautiful hardwood not being used on furniture .. well I just can't do it.

Now I understand that some ... many ... consider their shop as a place of private reflection, where one is free to worship brass and iron idols and icons, or just chat with mates over a beer. So I accept that shop furniture is high on the list of many. Just not for me. I work with recycled woods, many of which are now endangered ... like Jarrah. I bet you think that it grows on trees ;) In fact, the Jarrah forests have been decimated, for railway sleepers, fencing, firewood ... and the forests only grow in Western Australia. And now they have almost disappeared. I'd rather use wood like this for furniture in the house than in the shop.

So I built mine almost entirely from cheap, sustainable Pine, and used a little Jarrah here-and-there to tart it up. Three years ago, following an addition above the garage/workshop, I started from scratch with four bare walls - well, actually three since the fourth was a double garage door. I managed to get as far as a couple of cabinets, one for spokeshaves and braces, and another for rasps and files, and then added a saw till - none of which had doors or were protected against dust. I also constructed a long - open - set of shelves above the workbench for planes. The only cabinet that had a door was the one for chisels.

Dust, dust, dust ... oh how I hate dusting shelves!

This weekend past I decided to add doors to the shelves. This was going to be a quick-and-dirty job, using recycled cardboard (i.e. MDF) .. one morning tops, then I could get back to building something important, like the two campaign chests that were put aside about a month ago and sit there mocking me.

Well it got out of hand. The MDF doors got tarted up with Jarrah edging (OK still cheap-and-nasty, but they will do until the house is full of furniture), then I installed glass in the glassless doors in the spokeshave/brace cabinet (which I had built as part of a magazine article I wrote to illustrate joint making). And finally I rebuild the chisel cabinet to make room for all the new Japanese chisels (Kiyohisa slicks and Koyamaichi dovetail) that replaced a bunch I sold. And after this (so not finally!) I redid part of my hanging tools.

Enough with the words - where are the pictures!?

Just keep in mind that this is not about showing tools. More about tool storage. So if you want close-ups to see the tools, then ask (I am happy to oblige) but the storage has priority.

As I mentioned earlier, my shop is in a double garage and must share space with one car (two others live outdoors). There are power tools as well for the rough work ...



Turn around and face the rear of the garage, and now you are in the handtool shop. Facing you is my small workbench and above this are the MDF-Jarrah doors that now seal the shelves from the dreaded dust ...


The door on the far right is chisel cabinet. Inside it now looks like this ...


The only open section is where I keep the bench planes that are most used, a combination of woodies and Veritas BUs. Since these tend to be larger planes, it is easier to keep them out of the way if there is somewhere convenient to rest them ..


If you now do a left turn and face the far wall, this is what you see ..


That cabinet at the far left was the glassless glass doored offender. No longer. It now has glass ...



After this I realised that I really must fit glass-fronted doors to the remaining cabinets. This will be done next time ...

The lower cabinets were, in fact, a kitchen (well I thought that was just desert) that I was given by a neighbour who was upgrading. The tops are 1 1/2" plywood.



This cabinet provides easy access to rasps and plough planes. The drawer contains files in a roll.

The hanging tools. I find it easier to keep as many of the layout tools close at hand this way. I have shown this before so I will only show something new, this being the inclusion of my hammers/mallets. Keeping them off the bench top is a biggie. The bench is small (just 5 foot) and clutter makes it smaller (a new bench is on the drawing board ... one day).


Hope this provides some ideas for some. Feel free to ask for details, or post pics of your own solutions.

Regards from Perth

Derek

Re: Shop storage update

#2

Re: Shop storage update

roger lance

Derek....thanks for posting pictures of your great shop....I must admit that I am simply stunned at the sheer number of hand tools....you have more hand tools than most stores I've been in....what a collection !!....if I were not in my 60's, I'd ask you to adopt me....have a good day....Dad.

Re: Shop storage update

#3

Ellis Walentine

I'm envious

Ellis Walentine

Thanks, Derek. Your shop is a fine example of what can be done with a small space. There still may be hope for my disaster area.

Cheers,

Ellis

Re: Shop storage update

#4

Re: Shop storage update

Derek Cohen (in Perth, Australia)

Hi Roger

Thanks for the kind words.

I am always ambivalent when posting anything that relates to tools, unless it is about a tool I built or a tool review. I did, however, want to share some of the challenges - and solutions found - in managing a small shop. And the space I have is really quite small. Of course this is made more interesting when you have a library of tools, as I do :) I cannot promise to adopt you, but you are welcome to come over and use them at any time. :)

Regards from Perth

Derek

Re: Shop storage update

#5

Re: Shop storage update

roger lance

Derek...thats a very generous offer...and I thank you for it...I noticed that you had appropriately displayed a poster of the Studley tool chest...there are many nice attributes and characteristics said of Mr. Studley for the organization, treatment, care, and display of his beloved tools...those things could be said of you as well...and if I'm every sailing my 12 meter in your neighborhood; I'll stop over, crack open a cold one, put a few shrimp on the barbie, and make a shaving or two. Take care.