New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Is there any toxicity to powder metal dust?

Posts

Re: Is there any toxicity to powder metal dust?

#26

Masks are indeed important....

John in NM

And I don't wish to discourage anyone from using them as often as they feel necessary.

But I do think the context is important here - silica is virtually un-used in the grinding and polishing products available to hobbyists and light industry in the US - its all SiC, Alox, and Feox. Even green rouge is now alumina with some green dye, and a health rating of "1" on its MSDS.

Re: Is there any toxicity to powder metal dust?

#27

Being considerate of others

Bob Hackett

Anyone who has grandkids will be even more aware of dust and where it goes.

Everyone you come in contact with before you change your clothes and shower up will be exposed to that dust.Just because you don`t have a reaction doesn`t mean someone else won`t.That`s how my wife became sensitized to oak.

I have also read that beekeepers will many times have family members who have allergic reactions to bee stings.The minimal exposure to the residual bee particles over the years is enough to make them sensitized and allergic yet not enough to make them immune.

Re: Is there any toxicity to powder metal dust?

#28

Re: Right

GolfSteve in Calgary

Thanks for the great info David. I'm looking for something to contain the mess from the grinder. I had seen that Baldor system before, but $700 is a bit too much just to contain the mess. I almost always wear a mask in the shop because wood dust bothers my sinuses.

For work I'm purchasing some recirculating (portable) welding fume extraction systems, which consist of spark traps, carbon filters, and HEPA filters. Too rich for my shop. One of these would do a great job on my little grinder :-)

By the way, the work environment for the project in China is abnormally filthy. In most other projects the Owner takes much more care to develop a clean work environment so that you don't get so filthy. That is very hard to do in our line of work - sometimes filth is unavoidable, but sometimes filth is just laziness. Our previous job (in Australia) was very similar to this job in China, but the Aussie material contained a small amount of crystabalite, so we developed procedures to clean the work place and monitor dust exposures.

Re: Is there any toxicity to powder metal dust?

#29

That first picture is especially impressive....

John in NM

I never would have guessed that was a disposable mask if you hadn't told us :D

I've been doing a lot of power carving lately, using so-so 3m masks from Home Despot, I was thinking of getting a powered dealy, but I think I'll hunt up some moldex masks first and try them.

Re: Is there any toxicity to powder metal dust?

#30

David Barnett

Yeah, you're right about the green rouge

David Barnett

"Even green rouge is now alumina with some green dye"

Which is why I buy from chemical and ceramic suppliers or Kremer Pigments.

Re: Is there any toxicity to powder metal dust?

#31

Re: That first picture is especially impressive...

GolfSteve in Calgary

The guy in the first photo was probably wearing a 3M 8210 N95 mask without exhalation valve...it's the type he likes. They are cheap single use masks.

I prefer the Moldex 2740R95 mask. The handi-strap is very convenient for the type of work I do - when in a clean environment the mask hangs conveniently at the neck and can be easily put on when going outside again. The 2700N95 would also be a good choice.

I buy them at Acklands-Grainger. They cost about $5 each, but one mask will last for months in my home shop.

http://www.moldex.com/respiratory-protection/disposable-respirators/handystrap/

I've also bought the N100 masks, but they fit smaller due to a full-mask gasket (the N95 masks only have a gasket at the nose), and the N100 masks don't seal well on my face.

Re: Is there any toxicity to powder metal dust?

#32

the 8210

John in NM

Is what I've been buying, since they work better (in terms of sealing) than most others I've tried from the average hardware store. I find them too small though (big mouth, literally and figuratively :D), but that may just be that it's hard to find the larger size at my local Home Depot, I seem to remember having that problem.

Much as I hate to patronize Grainger, I may have to do so :D Looks like McMaster has them too, though not by name.