New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Modified Rabbet Plane

Posts

Modified Rabbet Plane

#1

Modified Rabbet Plane

Ralph Ambrosio

I just picked up Durant's book on building Adirondack Guide boats and have been studying the classic methods of building these beauties. I have gotten as far as the planking methods and came across mention of a specialized rabbet plane used for joining the long edges of the planks, one to another, about 8 to a side. The planks are around 3" wide and .25 of an inch thick. They are clench nailed together every inch or so and double clench nailed around the more extreme bends in the hull.

Anyway, my question is this: The book mentions a rabbet plane that is used to uniformly cut a lap on each long edge that leaves an elongated "Z" profile with the top and bottom of the "Z" being .028" deep instead of a weaker feather edge. The middle of the "Z" profile being 22/32" wide.

The plane sounds custom made to me, but you never know. Sounds a little like what I imagine planes used to make raised panels are like, only in miniature. If it is custom, where could you go have it made or is this so exotic that I should stop looking and figure out another way to go.

Thanks for reading and sorry for the cryptic attempt at explaining what it is I am looking for.

Ralph

Re: Modified Rabbet Plane

#2

Words and pictures

Bill Houghton, Sebastopol, CA

Ralph,

If you have a scanner, a drawing of what you mean would be helpful - I'm having a little trouble picturing it.

Sounds custom made to me, but maybe with a drawing, someone can pipe up with how to adapt a commonly available plane; or how to make a simple woodie for the job.

Boats always kind of amaze me in the same way that guitars do - there's often so little wood accepting so much stress, but they don't immediately sink and/or fall apart.

Re: Modified Rabbet Plane

#3

Re: Modified Rabbet Plane

Ralph Ambrosio

Good idea, hope this image helps. It is an edge on view of the planking profile of the amidships rib. This particular plank is 3/16" thick.


Re: Modified Rabbet Plane

#4

Re: Modified Rabbet Plane

Matt Bickford

I've met several boat builders in the last year. I always have a lot to talk to them about because they've each made several planes, including the exact one you reference.

Re: Modified Rabbet Plane

#5

Re: Modified Rabbet Plane

Pam Niedermayer - Austin, TX

Your "Z" description did it for me. I immediately pictured a very high angle (I'm guessing 45�) scarf joint, which is what you've shown here. Does the book mention why the author doesn't use tongue and groove?

Pam

Re: Modified Rabbet Plane

#6

Re: Modified Rabbet Plane *LINK*

Bill Houghton, Sebastopol, CA

I'm not Ralph, but Ralph did mention that the planks are clench-nailed (like riveting) together, which requires a fairly broad overlap.

An interesting variation on lapstrake construction (see linky, one of many), which served the Vikings right well. Seems like a lot of work to go to for a smooth hull.

But then, I've not only never built a boat, I don't even swim, so I should shut up and let people who know something about it talk.


http://www.danenbergboatworks.com/lapstrake.htm

Re: Modified Rabbet Plane

#7

Re: Modified Rabbet Plane

Pam Niedermayer - Austin, TX

Usually scarf joints are longer and at a lower angle. It appears that Ralph's planks don't overlap as in lapstrake construction, which seems more like clapboarding than anything else. I'd expect the scarf joint construction to produce a faster and more easibly turnable boat, given its smoother bottom.

Pam, who hasn't built any boats either, but was a very early swimmer

Re: Modified Rabbet Plane

#8

Smooth hulled boats

Bob Hackett

The plank on frame smooth hulled vessels are called Carvel planked hulls and they have no overlap on the planks at all.They actually have a slight gap between planks which is caulked with oakum and then cotton caulking to make them water tight and then the caulking is covered with seam compound to smooth the seam and prepare the hull for painting.

Once a wood hull becomes wet it will swell and become water tight.We used to run hoses into the bilges of wood boats that had set in storage for long periods of time and let them swell till they began to hold water.Then we`d rig extra bilge pumps and launch them.Once they stopped taking on water we`d remove the extra bilge pumps,make sure the batteries were up to snuff and move them from the dock to a mooring.

Planked boats leak like a sieve if held out of the water long enough to dry out.

Fiberglass and metal hulled boats will take on water after an extended period out of water too.The stuffing box sealing the prop shaft and rudder shaft will usually leak till they either swell or are tightened.

Re: Modified Rabbet Plane

#9

OT - for a good (reading) time

Bill Houghton, Sebastopol, CA

track down Farley Mowat's "The Boat Who Wouldn't Float." He has some lovely things to say about the tendency of wooden boats to leak until they, to use the term common in Canada's Maritime Provinces when he had his boat, "take up."

You will need plenty of floor space around you when you read the book, so as not to hit anything when you start rolling around on the floor, laughing.

Actually, almost all of his books are worth tracking down. Many are funnier than can be; some are funny in the midst of white hot anger (for one of those, try "Never Cry Wolf."); some are rather more serious but still great reads.

Re: Modified Rabbet Plane

#10

Re: Modified Rabbet Plane

Ralph Ambrosio

Bill, Pam, Bob and Matt,

Building a boat like this is very stylized. Once you have seen one of these boats and you decide to build one, you are in for the hunt. I have built several small wooden boats including clinker and cedar strip. Pam, the cedar strip is similar to t&g, it is bead and cove. The bead and cove are glued and then covered with fiber glass. I am lucky to live in upstate NY about 90 minutes from the Adirondack Museum at Blue Mt Lake, NY. See, http://www.adkmuseum.org/exhibits_and_events/. I have seen real guide boats up close, they are very, well, elegant.

Take a look at this site...http://www.guideboats.com/construction. John Gardner, the all time expert on all things wooden boat, says that this planking method is the toughest part of the entire endeavor.

I have turned the air in my garage shop blue on several occasions, once, without my realizing it, my 4 sons came into the shop to get me to take them to the Town Pool and, well, I explained it as a part of boat building, my oldest, 12 at the time, knowingly explained to the rest of the guys that "Dad used to be in the Navy, and sailors swear a lot when they build boats."

Bill, I think I need a plane maker or a good book on plane making. God, the thought of making a plane makes me think I am in deep water and although I can swim...I just don't know if I am ready for the English Channel.

Thank you all, if you come across something, let me know.

Ralph

Re: Modified Rabbet Plane

#11

Re: Modified Rabbet Plane

Pam Niedermayer - Austin, TX

To do your "Z", more or less, I think all you need is a chamfer plane with one of the fences removed. A big chamfer plane. Or, as you said, a very modified rebate plane, one with a fence added on one side. Probably you'll need both a left and right handed plane to accommodate grain.

ThomD has built boats, so I'm sure when he shows up any minute now he'll have something useful to say.

Pam