Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

thin chisels for dovetails

Posts

thin chisels for dovetails

#1

thin chisels for dovetails

les winter

I saw David Charlesworth pare dovetails vertically, from the end grain, down into to the bottom of the tails and pins on one of his videos. I like the technique and use my Blue Spruce paring chisel to do it.

Today I decided to fool with a few narrowly spaced tails. The only blade in my shop that will allow me to pare vertically is an old Record block plane cutter ground at 25 and honed at 26. I don't like paring with a plane iron.

Anyone have a better solution?

thanks

Les

Re: thin chisels for dovetails

#2

Re: thin chisels for dovetails

Dean J in MN

Thin like this?


I (and a 3 others) just made a set like this, from 1/16" wide to 2" wide. The one pictured is 1" wide and right around 1/16" thick at the start of the bezel. We shot for that thickness even in the 2" wide tools, though they did turn out closer to 3/32" thick. There was variance in our blade tapering setup. :)

(Sorry, just boring O1)

Dean

Re: thin chisels for dovetails

#3

Re: thin chisels for dovetails

les winter

Yup. Like that.

Re: thin chisels for dovetails

#4

Sounds scary to me...

Scott Burr in Ben Lomond CA

Isn't that just asking for the wood to split? Especially in thin wood, like a drawer side or small box.

Re: thin chisels for dovetails

#5

Question about the method

Wiley Horne--So. Calif.

Hi Les,

Just one question if you don't mind. Is this technique used to correct sawing mistakes, or does it involve sawing shy of the line (on purpose) and paring to the line?

Thanks, Wiley

Re: thin chisels for dovetails

#6

Re: thin chisels for dovetails

Derek Cohen (in Perth, Australia)

I saw David Charlesworth pare dovetails vertically, from the end grain, down into to the bottom of the tails and pins on one of his videos. I like the technique and use my Blue Spruce paring chisel to do it.

Today I decided to fool with a few narrowly spaced tails. The only blade in my shop that will allow me to pare vertically is an old Record block plane cutter ground at 25 and honed at 26. I don't like paring with a plane iron.

Anyone have a better solution?

Hi Les

I have done something that may be similar, that is pared vertically. However I have only ever done so on the pins, never on the tails.

If you cut the tails first, as I do, then these are the templates for the pins. You would only want to adjust the pins (if you need to adjust at all).


On the pins, if your saw cut is slightly inside the mark, you will see the knifed line. I usually just place the chisel in this and - carefully - push downward to remove a sliver of wood. You do not need a special chisel for this. Still, this can be a very risky method as it is too easy for the grain to deflect the chisel off line. It is better to pare from the sides.

Am I missing something here - did I understand you correctly?

Regards from Perth

Derek

Re: thin chisels for dovetails

#7

Re: thin chisels for dovetails

les winter

Maybe I incorrectly explained what's what. David Charlesworth recommends vertical use of the chisel to slide down the face of the tail or pin to get at the last little bit of tissue remaining at the baseline of the tail or pin. Nothing is removed from the face. The chisel just penetrates the base line, and then horizontal paring is used to remove any remaining unwanted material.

Re: thin chisels for dovetails

#8

Re: thin chisels for dovetails

Derek Cohen (in Perth, Australia)

Hi Les

You could use ..

1. skew chisel

2. sharpened cabinet scraper blade

3. long knife blade

Regards from Perth

Derek (who will have another gander at the DC DVD on chisel use later)

Re: thin chisels for dovetails

#9

Re: thin chisels for dovetails

les winter

Well I got up early, took an old greenlee 3/4" chisel to the grinder and ground off an inch at a 20 degree bevel. Tedious. Then attacked the back. It still isn't perfect, but it reaches. I would figure that someone makes a paring chisel that is less than 1/16th thick. I guess not.

thanks for the input.

Les

Re: thin chisels for dovetails

#11

Ellis Walentine

Yeung Chan's toolbox

Ellis Walentine

Yeung Chan has a whole box full of knives and thin chisels like you are describing. He makes them from scratch from industrial hacksaw blades.

Ellis

Re: thin chisels for dovetails

#12

Re: Yeung Chan's toolbox

Catharine Kennedy

apparently he was the designer for the Veritas detail chisels

Re: thin chisels for dovetails

#13

Re: thin chisels for dovetails

R Payne

I make my own from what is sold as music wire in hobby stores (treat like 1095). Real easy to do and these are small enough they can be done with a plumber's torch. Heat an end until it is glowing red and hit with a hammer (on something hard and fire proof, of course) to a little thicker than the desired thickness. A couple of whacks should do it. If the glowing red color goes away before you get there, heat it again.

Use coarse sandpaper to remove the scale. Take a file, sandpaper or grinder and shape it to what you want but leave it unsharpened.

Back to the torch for heat treat.

Sharpen.

ron

Re: thin chisels for dovetails

#14

Ellis Walentine

What gauge wire?

Ellis Walentine

I like this idea, Ron, but I'm thinking I'd need wire that was at least 1/4" in diameter to make even a narrow chisel. Is this wire available in heavy gauges like that?

Ellis

Re: thin chisels for dovetails

#15

Dean, How Did You Get .  .  .

Tom Colligan

the bolster on your 1/16th paring chisel? (I'm assuming you made the tool yourself, no?) TIA, Tom.

Re: thin chisels for dovetails

#16

Re: What gauge wire?

R Payne

I think the last time I bought some, the shop I was in had 3/8" diameter, the largest I bought at that time was 1/4". I also bought several smaller sizes. I originally made a mortice chisel for morticing replacement handles I was turning for the fencing club I belong to. Then I made a couple of chisels just under 1/16" thick, I think one is 3/16" wide and the other is 1/8".

The steel will expand sideways as you hammer is out. I can get a 3/8" wide by a bit thicker than 1/16" out of 1/4" if I'm careful with my hammering, maybe a little more, after shaping. If I use a cross peen I can get wider. (The cross peen will direct the spreading of the steel more in one direction.) If you really want wider you can buy drill rod (in larger sizes) or upset the music wire.

ron

Re: thin chisels for dovetails

#17

Ellis Walentine

Thanks

Ellis Walentine

Worth looking into.

Cheers,

Ellis

Re: thin chisels for dovetails

#18

Hi all... *LINK*

Scott Burr in Ben Lomond CA

For your enjoyment and for everyone's who wanted to build your own twinscerw vice also, here you go...

My only complaint is that there is a minimum order in $ that is.

Cheers!


A really cool place...

Re: thin chisels for dovetails

#19

Re: What gauge wire?

Thomd

O1 is easy to get in larger sizes, the supplier I use tops out at .146. There are suppliers of 1095 though, if you want that.

http://www.victornet.com/subdepartments/Music-Wire/1040.html?id=YkNRfz7q

Re: thin chisels for dovetails

#20

Re: Dean, How Did You Get .  .  .

Dean J in MN

Tom,

All of the bolsters are just mild steel we punched tapered square holes into. The tang is ground into the body of the chisel, with a shoulder to stop the bolster from sliding down. From there it is a press fit of the bolster, which is ground/filed to shape.

I'd call the 1/16" a paring chisel, but in general use these are former(firmer)/paring chisels, the only difference is the final honing bevel is steeper on the formers.

Dean

Re: thin chisels for dovetails

#21

Why is it called "music" wire?

Pam Niedermayer - Austin, TX

Re: thin chisels for dovetails

#22

Re: Dean, How Did You Get .  .  .

Pam Niedermayer - Austin, TX

Pretty cool. Do you know how these compare to your average Japanese ultra/very thin chisel?

Pam

Re: thin chisels for dovetails

#23

Re: Dean, How Did You Get .  .  .

Dean J in MN

No idea Pam, I am not a student of eastern woodworking so wouldn't even have a context to place a description/comparison in.

-Dean

Re: thin chisels for dovetails

#24

It's also referred to as "piano" wire.

Marv

Re: thin chisels for dovetails

#25

Re: thin chisels for dovetails

Mark Salomon

I also like to clean up that last little bit and have been frustrated by the blade thickness of my chisels. To solve it I had Dave Jeske of Blue Spruce tools make me a thin chisel based on his large marking gauge. Specifically, I had him square the blade instead of tapering it and put a 25 or 30 degree bevel. Works great and matches my marking chisel.