Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Grinding wheels revisited

Posts

Re: Grinding wheels revisited

#26

Re: Wolverine Grinding Platform

Bob Hackett

The Wolverine is all steel and uses integral handles so you need zero tools for adjustments.The handle to adjust the tool rest angle is indexible thru 360 degrees so you can always move it out of your way.You pull it out,turn it where you want it and push it back in to engage.

BTW-Just as you can camber a grinding wheel you can dress the face at a slight angle to get you by that motor housing provided it`s not a BIG housing.Just don`t go overboard to where the inner(bigger diameter) edge is weakened and liable to fail. :O

You can also buy a tool room wheel that is meant to grind on what we would normally consider the side of a wheel.They look sort of like an angled cup wheel.Just something else to think about rather than selling the grinder and buying a new one because the motor`s in the way.

Re: Grinding wheels revisited

#27

Thanks for the good info, Bob

Steve Elliott

Re: Grinding wheels revisited

#28

Re: Or...

Pam Niedermayer - Austin, TX

I'm a dyed in the wool BMW rider, in the midst of reviving my R90S and hanging another sidecar on it; although I've added a Vespa or two to the mix, just for commuting to UT. I love the looks of the Ducs, et al, but my first Honda cured me of any love for chains. My first HD, Sportster Cafe, cured me of any desires in that direction, shook itself apart as I rode down the streets, ran right back to Beemers asap. I've heard they got much better for a few years.

Pam

Re: Grinding wheels revisited

#29

Re: 3. Dust control

anotherBob



GolfSteve in Calgary

3. Dust control. I'd like to see integrated dust collection. My delta has connections on the shroud for dust extraction, but obviously I will not connect this to anything that may collect combustible materials (eg. paper shopvac bags, sawdust, etc). I hate truing up a wheel and getting dust all over my shop!!!


Trash Can Cyclone Lid

http://www.woodcraft.com/Family/2004310/Trash-Can-Cyclone-Lid.aspx

I have one of these hooked up via a spare hose into a metal trashcan dedicated for just grinder dust/sparks. Works great and only takes a couple seconds to switch back for wood chips/dust.

Re: Grinding wheels revisited

#30

If you're going to go older English, do it right

Bill Houghton, Sebastopol, CA

get a Velocette.

Re: Grinding wheels revisited

#31

Don`t I wish!

Bob Hackett

You did notice all the old bikes I mentioned were pre-unit construction,didn`t you?

Is it too late to change my old Indian wish to a Crocker?

Re: Grinding wheels revisited

#32

Like Pam, when I rode, I was a BMW rider

Bill Houghton, Sebastopol, CA

but I might make an exception for a Velocette.

Re: Grinding wheels revisited

#33

Grind to the very edge? *LINK*

Wiley Horne--So. Calif.

Joel,

Thanks, freehand will make it easy.

Do you grind all the way to a burr? If so, with which grit? I see you're advertising 46g, 60g, and 100g, in I grade, for 6", 7", and 8" wheels.

Wiley


Norton 3X seeded gel wheels

Re: Grinding wheels revisited

#34

Re: Grind to the very edge?

Joel

I use a 6" 3x wheel running at 3600 RPM. I grind to a wire edge. All it takes is a clean wheel, a light touch, and patience. The last bit seems to take forever. a 46 grit wheel will run a little cooler, a slow speed grinder will take longer but run a little cooler too. stopping before the wire is formed is of course safer, but going all the way means the least work on the stones and feels right to me. Most of this is practice to learn when the wheel needs redressing, and leaning how the right touch on the wheel.

Re: Grinding wheels revisited

#35

I would have been a Beemer rider, but

Bruce, a MN Galoot

I have a friend whose uppity attitude toward BMWs and their owners has pretty much soured me on them.

I do love my old Wing - old enough to still have some character and look like a motorcycle.

Re: Grinding wheels revisited

#36

Re: I would have been a Beemer rider, but

Bob Hackett

I like BMW but I just don`t see a former outlaw bike club member fitting in with that crowd either. 8)

Call me a rebel(others do) but if you have 2 wheels under you and can keep up then it`s all good as far as I`m concerned.

When it comes to viewing or repairing/restoration then the old iron is where my heart is at,any old iron.

When it comes to a cross country run and reliability then give me German or Italian engineering from the factory or a hand built custom(that my buddies and I built and know).

Purist is not a word(or concept) in my general vocabulary,way too limiting.

Re: Grinding wheels revisited

#37

The power of grinding to the edge.

Derek Cohen (in Perth, Australia)

Grinding to the edge, or as close to the edge as possible, is likely to become "best" sharpening strategy. When it is not possible on a high speed grinder, either because the equipment makes it risky to do, or because the user lacks the experience and/or skill, then the wet grinders should be looked at. Wet grinders make this task safe and easy, albeit a slower process.

I state this not from some belief that those that hollow grinding is superior to other forms of blade preparation, but just that it makes it easier to create a micro bevel. I think that we will discover that this is increasingly important as we move into an age of more absrasion-resistant blade steels that promise longer edge holding.

My experience with A2 is reasonably long standing, that with 'V3 and D2 is more limited in time. Nevertheless I do anticipate that it is possible to hone the latter steels without needing recourse to diamonds. Sharpening media - waterstones, ceramic stones, oil stones, etc - all differ in the speed that will abrade these abrasion-resistant steels. Not working fast enough gives the impression that they are tough to sharpen, plus you run the risk of not sharpening enough.

You need is to reduce the amount of steel to be honed to the minimum. This is where a hollow grind to the edge is important.

I honed a '3V blade this afternoon and timed myself. The blade was used for shooting so hollow ground at 25 degrees. Most of the grinding was completed on a 8" half-speed grinder with 46 grit white wheel, and then finished on the Tormek to a wire edge. This was followed by freehand honing micro bevels on the hollow.

Using Shaptons 1000/5000/12000 ...

3 strokes on the 1000

4 strokes on the 5000

5 strokes on the 12000

The total time for honing was 1 minute 45 seconds.

This was sharp enough to shave hair, and then sharp enough to plane end grain Jarrah (1 1/2" thick) and Tasmanian Oak (3/4" thick .... this wood is about the same density as White Oak) for 20 minutes without any signs of the edge failing or the sharpness dropping off. Nice shiny surfaces.

Regards from Perth

Derek

Re: Grinding wheels revisited

#38

Re: The power of grinding to the edge.

Wiley Horne--So. Calif.

Derek,

Thanks for the excellent detail. Couple of questions....What is the grade (as in hardness--I, J, K) of the 46g white wheel?

Also, regarding the 3V iron to be used for shooting, is this blade going into a bevel-up plane? I ask because I have forgotten whether you recommend hollow grinding of BU irons--I think so, but want to be sure. It strikes me that hollow grinding BU irons could be a major key to maintaining the backs in good order.

Wiley

Re: Grinding wheels revisited

#39

Re: The power of grinding to the edge.

Derek Cohen (in Perth, Australia)

Hi Wiley

I'm not sure how you see "hollow grinding BU irons could be a major key to maintaining the backs in good order"?

Then you wrote, "I have forgotten whether you recommend hollow grinding of BU irons".

The only BU blade I hollow grind is the low angle 25 degree one. This is easy-enough to freehand. The big advantage of BU planes is that you can achieve a high cutting angle by altering the angle of the bevel. However bevel angles of 40 degrees and above, especially 50 degrees and above, are too difficult to create via a hollow grind. How would you freehand hone an angle that high - it is too cumbersome. Further, you would not be able to camber the edge as the steel would be too thick. It is far better to hone a high micro secondary bevel on a low 25 degree primary. The primary may be hollow or straight ground. Then use a honing guide to obtain the bevel degree you want.

Regards from Perth

Derek

Re: Grinding wheels revisited

#40

Same page I think

Wiley Horne--So. Calif.

"The primary may be hollow or straight ground. Then use a honing guide to obtain the bevel degree you want."

Hi Derek,

Your method stated above is what I was suggesting--hollow grind the primary bevel and hone to what you want. Not to balance the blade across the hollow grind, but rather to minimize the amount of metal to be removed during resharpening.

Your method seems ideal, because it minimizes the metal removal needed to erase the lower wear bevel on the blade back. Since the wear on the blade back is removed by working the bevel side, it is good to keep the bevel short! You have made this point a few times before--that it is always better to use a 25 degree BU blade + secondary bevel, rather than switch between blades with higher and lower primary bevels.

On the other point, I'm still wondering about the hardness of the 46g wheel, if you know it. The reason for starting this thread was to get specific data on what different people are using for hollow grinding.

Thanks,

Wiley

Re: Grinding wheels revisited

#41

Re: this is a little outa hand

thomd

I'd keep an eye open for a baldor these days. This is a bad part of the world for second hand stuff but even here they show up periodically online. Well worth the same dollars as a grizz.