Wooo Hooo!
Scott Burr in Ben Lomond CA
Well done! I would have been shaking in my boots when it came to getting them to fit, let alone driving them home.
Knowledge You Can Build On — Est. 1998
Wooo Hooo!
Scott Burr in Ben Lomond CA
Well done! I would have been shaking in my boots when it came to getting them to fit, let alone driving them home.
Re: One man operation
Wiley Horne--So. Calif.
Nother question......why the gigantic legs?
Hi Marv,
One of the key features of the Roubo bench is that it has large double tenons on each leg. These double tenons are doing the work of an upper rail. The original Roubo also has the big legs, which are needed to form the two big tenons.
Wiley
Re: One man operation
wilbur
Hi Marv,
Thanks for the description of using blocking. The one thing that I'm not clear on is, if the workbench is sitting on the cross beams that is sitting on the stack of 2x4's, what does the pry bar sit on so that I can lift the bench?
"Question....will you be champfering the edges at the bottom end of the legs to prevent splintering?"
Already did that when I first made the legs
"Nother question......why the gigantic legs? Is the purpose for all the massive construction so you end up with a heavy bench? A wood lathe is often made heavy to make it stay put by having a sand box inside the legs to keep the machine from moving around.
This bench is based off of Roubo's bench. As Wiley said, the original reason for the thick legs is to allow it to have double tenons on the ends. That is the engineering answer for the thick legs. The thick top traditionally was sawn from a single large slab of wood about 5-6" thick. As the bench top dried, the shrinkage would tighten its grip on the leg tenons, and would cause the legs to splay a bit outwards, which made the bench more stable over time.
But the real answer as to why am I building such an overbuilt bench is that it just looks way cool.
That should be reason enough for most things that we build, no?
Re: One man operation
Marv
Wilbur,
What do you pry on to lift the bench? Sorry, forgot to mention... Another stack of blocks. As you lower the bench, you remove one of the blocks that you pry on. The whole process is time comsuming but sometimes when you must rely on only yourself, most every thing seems to take longer.
As I ponder your situation more, I think what I would do is just slide your bench over to one side as far as possible with it still on the saw horses and tip it toward you and allow it to rotate down until the two legs farther away from you touch the floor. Then, merely tip it on over onto all four legs. If the saw horses are still holding it up a little, just inch it off the saw horses little at a time.
Was the bench perhaps designed during the renaissance period when women with huge legs were in vouge? 
In any case, I think you've done a fantastic job. Now just think how much easier your next bench will be. Now just a nice even coat of John Deere green 
Marv
Re: One man operation
Bob Hackett
Do they make milk paint in John Deere green?
I don't know, Marv
Bill Houghton, Sebastopol, CA
your proposed method sounds pretty high risk.
Congratulations!
James Watriss
Well done... has to be a good feeling.
2 things: (my advice... take it or leave it)
-Remember to make a promise to yourself that this bench will NOT become just another horizontal crap-catcher.
-When you flip it over and get it into position, remember that the first thing you should do is drive either a nail or a drywall screw into the top. I know it sounds sacreligious. But I do that on all of my benches to remind myself that they're tools, to be used as tools. This, for me, is the equivalent of jointing and hollow-grinding new chisels. It feels wrong, somehow, to mess up the shiny newness. But it's also akin to the soccer coach who tells his kids to go roll around in the mid before the big game... so they can focus on the game, and not on staying clean. You can always pull the nail or screw back out... in fact, that's pretty critical, really. But you get the idea.
Re: I don't know, Marv
Marv
Bill,
Most of the weight will be on the saw horses while tipping the bench. I just don't think it is so heavy that one man couldn't guide it as it is rotated. If the risk seems a bit too much for one person, the method would still be the best way IMO, even if more than one person did it. It would prevent having to lift the entire weight
Marv
Pretty deer grean...
Scott Burr in Ben Lomond CA
You'd have to mix some earth green with just straight green, no problems 
Just make some test boards to see what it looks like after you apply the top coat.
Re: Pretty deer grean...
Bob Hackett
You may be able to get that color,but it don`t mean a thing if you ain`t got that JD shine!
You know that SHINE,the one that makes the combine stand out in the field of corn. 