Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Drawer design and drawer bottoms

Posts

Re: Drawer design and drawer bottoms

#26

Re: Drawer design and drawer bottoms

Derek Cohen (in Perth, Australia)

>Wonderful Richard!!

This definitely should be a chapter - not just on a website, but in a book.

Too late this time around, but I will use it in the next project.

Thanks again.

Regards from Perth

Derek

Re: Drawer design and drawer bottoms

#27

Re: HDPE

Bill Houghton, Sebastopol, CA

>I did a similar repair on our failing kitchen drawers using scrap kitchen-counter laminate. If I recall correctly, because I wasn't using glued-on wooden slips, I built up the worn grooves using Fixall - but it was some years back, and my memory isn't as reliable as it once was, and what were we just talking about?

Not a fine furniture solution, but these cabinets were holding down the opposite end of the furniture continuum.

Re: Drawer design and drawer bottoms

#28

Re: Drawer design and drawer bottoms

Pam Niedermayer, Austin, TX

>I don't pretend to understand all this, but I do agree with your 1/2" drawer bottom, 1/4" being entirely too thin and pliable in a drawer 30 X 17 (DAMHIKT) and liable to stretch out of regular American grooves even with a light load.

Pam

Re: Drawer design and drawer bottoms

#29

Re: Drawer design and drawer bottoms

Sgian Dubh

>Pam, it's still possible to use 1/4" thick material in large wide drawer bottoms intended to carry a heavy load. The solution is to include a drawer muntin or two in the construction. Muntins are similar to slips in profile, but are, in section view, a two edged slip with a groove on both edges along with other matching profile requirements. They are useually made 3 or 4 mm thinner than slips so that the bottom face doesn't wear any cabinet parts below as the drawer opends and closes, eg, dust boards and framing, or a solid/continuous horizontal runner/kicker.

The muntin is dovetailed, glued and screwed into the bottom edge of the drawer front, and notched around the bottom edge of the drawer back as per one of my earlier sketches of the slip, and similarly glued and screwed in place. Slainte.

Re: Drawer design and drawer bottoms

#30

Re: Drawer design and drawer bottoms

Pam Niedermayer, Austin, TX

>Sure, muntins are good. In fact, my preference for wooden runners should take care of this potential problem as the drawer part of the runners provide a lot of support; but I still prefer a thicker drawer bottom for the additional structural integrity it provides.

Pam

Re: Drawer design and drawer bottoms

#31

Wandering OT

Bill Houghton, Sebastopol, CA

>Bill,

Your comment on the Accuride slides prompts me to ask the following question. Context: some time in the future, I hope to build a hand tools cabinet consisting of drawers for planes, chisels, etc. - kind of a larger version, of wood, of a mechanic's rollaway, but probably without the wheels.

It has occurred to me that if I used the kind of metal drawer slide that wraps around the bottom of the drawer a little, or undermount slides that sit entirely under the drawer, I might be able to construct drawers in which the bottom runs entirely across, resting on the slides, with the sides then resting on the bottom, with nails or screws driven up through the bottom into the sides.

Is there some reason that this would not work? It would maximize space use and could be a strong design if worked out right; but maybe I'm missing some essential issue.

Re: Drawer design and drawer bottoms

#32

Drying drawers

Andrew F in Australia

>Hi Derek,

On a side track, I noticed that you'd clamped your drawers square and left them to dry out of the carcase.

Another way to consider may be to glue and clamp them approximately (within a couple of mm of square,) then remove them from the clamps while the glue is in the final stages of gelling and put it into the carcase with the front sitting about 1" proud of the drawer blade/rails. Make a few adjustments to ensure that you're happy with the fit/alignment.

In this way, it ensures that the drawer dries parallel to the blade, so that the fitting part is easy(-ier?) If the drawer is glued up at a different angle to the face of the carcase, you'd have to plane a bit of material off the front and then re-run the bead you've applied.

Re: Drawer design and drawer bottoms

#33

Distance? upper surface of drawer bottom to runner

Andrew F in Australia

>Hi Richard,

Just a quick question on spacing.

We were taught that the traditional drawers had a distance of 3/4" between the upper surface of the drawer runner and the upper surface of the drawer bottom. "must"

This means, that if the drawer bottom was 1/4" thick, that there's a 1/2" gap under the drawer bottom.

Looking at your work, it looks as though you leave a bit less than this.

Have/were you taught an empirical formula similar to mine, or do you judge the location of the drawer bottom differently?

I'd be interested to hear your observations. Does older furniture match the dimensions that I was trained in, or otherwise?

I must admit that on the current project I'm making (desk for family,) the 4" high drawer loses a fair bit of storage with the top of the drawer slip/groove set to be 3/4" off the drawer blade. THis got me thinking a week or so ago if the less taller drawers ('shorter' drawers for want of a better word, too early in the morning here,) were produced with a smaller offset between the drawer bottom and the slip. There's no practical reason why this couldn't be so, but things are always done for a reason in my experience, sometimes for logical reasoning, othertimes for illogical causes.

Cheers,

Andrew F

Re: Drawer design and drawer bottoms

#35

no dramas - one comment I forgot.

Andrew F in Australia

>Hi Scott,

It's obvious, but you've got to make sure that there's no glue on the outside of the drawer when you do this.

I've seen a few half finished drawers glued into their opening - now, as they're a really tight fit, how do you get them out?

Cheers,

Andrew

Re: Drawer design and drawer bottoms

#36

Re: Distance? upper surface of drawer bottom to ru

Sgian Dubh

>I haven't come across that 3/4" 'rule' Andrew. I usually aim for somewhere between 1/4" and 1/2" between the bottom face of the drawer bottom and the upper face of the divider/runner/shelf under it. Small drawers get 1/4" and larger drawers get closer to 1/2". It just depends on the drawer size, the load expected, the drawer bottom thickness, and what 'seems' about right at the time, ie, what mood I'm in, ha, ha. Slainte.

Re: Drawer design and drawer bottoms

#37

Re: Distance? upper surface of drawer bottom to ru

Andrew F in Australia

>Thanks Richard - the drawer that I'm making at the moment was the one that really looked out of place once I'd already ripped stock 2mm oversize, but that's the way that this one is going to stay, unless I can find the balance of the board and I might re-widen the board and redo it.

The 'rule' is definitely out of place here, but it's what's taught.

Cheers,

Andrew F

Re: Drawer design and drawer bottoms

#38

Tool Cabinet Drawer Slides

Steve Elliott

>The construction you describe was the standard drawer in a shop I worked at about twenty years ago. It had been chosen there to cut down on construction time, but it made a drawer that was able to hold weight up to the rated limit of the drawer slide without putting stress on the drawer box itself. We used 3/4 extension Blum slides, which wrapped around the bottom of the drawer box and covered the edge of the drawer bottom. This was for drawers with an applied front, not my favorite for style but pretty much standard for kitchen casework these days.

If you decide to do this I'd look for the drawer slides first and make sure the weight rating was sufficient, and also check for the fasteners that hold the slide onto the drawer. They don't need a lot of holding power but I prefer that they don't go into the end grain of the drawer bottom.

Full-extension undermount slides have the same advantage of supporting the drawer bottom but they tend to reduce the amount of useable space in the drawer by taking up some of the available height. For a tool cabinet with a lot of fairly shallow drawers you might lose considerable storage.