Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Saw carrier/tool box for Japanese saws?

Posts

Re: Saw carrier/tool box for Japanese saws?

#51

kerf

paul womack

>Only part of the sawing is parallel to the grain, most of it can be at an angle.

In a 12" long kerf, 1/2" deep, I'd call that (very) close to parallel.

BugBear

Re: Saw carrier/tool box for Japanese saws?

#52

Re: kerf

Pam Niedermayer, Austin, TX

>Yes, that's true; but my assumption was that the depth would be determined by the saw. Most saws are more than 1/2" deep.

Pam

Re: Saw carrier/tool box for Japanese saws?

#53

Re: kerf...tooth guard...

Marv

>Pam,

A tooth guard is only for the teeth not the whole blade. So a half inch deep kerf is plenty, then maybe a quarter inch below that, that makes up the total height. I usually only rip about 3/8" deep.

Marv

Re: Saw carrier/tool box for Japanese saws?

#54

I have the impression Pam was picturing

Bill Houghton, Sebastopol, CA

>a guard that protected the saw blade from dings and bending pressure as well as protecting the teeth - which is what Wiley asked about at the beginning of this thread, if I recall (to quote Arlo Guthrie, "Remember Alice?" as the conversation wanders).

That would be a cut of a depth I find intimidating to think about in thin wood, though I guess it'd be good practice.

Re: Saw carrier/tool box for Japanese saws?

#55

And as usual, you are correct. :)

Pam Niedermayer, Austin, TX

>

Re: Saw carrier/tool box for Japanese saws?

#56

Vespas with sidecars *LINK*

Bill Houghton, Sebastopol, CA

>I believe they were not uncommon in Europe - not so much here (but then, from after WWII until recently, sidecars were uncommon in this country attached to anything).

Goggling "Vespa sidecar" gave me more references than I'd have thought possible.

Bill, always intrigued by sidecars, but stopped riding before I got one.


http://www.arsscoot.com/

Re: Saw carrier/tool box for Japanese saws?

#57

Re: Vespas with sidecars

Pam Niedermayer, Austin, TX

>The problem with sidecars is you still get wet and you get stuck in traffic just like cars, as I found out in Boston when I hung one on my Beemer (R90/S) for carrying camping and photo gear, to say nothing of driving in snow (better than a car, but cold). It was gone within a year.

Austin is not so bad as Boston and I only have 3-4 miles to go daily, and I now have this huge pooch who can't fit on the back seat.

My rig will be all white, will look something like this except for no windscreen on the scooter.

Pam


img

Re: Saw carrier/tool box for Japanese saws?

#58

You folks are real sick puppies.

Bob Hackett

>Hanging a sidecar on a poor unsuspecting(and seemingly underpowered)scooter like that!

I once modded a Suzuki(350-450cc)to accept a Sidestrider so a local could haul his LARGE dog around with him.He also has been known to remove the seat,pack it with ice and lobsters and head out for local deliveries.A serious prewash is always performed before the lobsters take up residence in the sidecar I`m told(the dog drools alot).

Mainely,Bob

Re: Saw carrier/tool box for Japanese saws?

#59

Re: You folks are real sick puppies.

Pam Niedermayer, Austin, TX

>At least he knew how to hold down the sidecar on right turns. :) The P200 Vespa is underpowered only outside of town. In town, you just don't need the speed. Besides, the car I'm putting on it is a Piaggio design copy, very light weight, not suitable for a sidecar load more than 170 pounds. My goal is 40 mph on the steep hills of Austin.

But "sick puppy?" Probably.

Pam

Re: Saw carrier/tool box for Japanese saws?

#60

Consider, though...

Bill Houghton, Sebastopol, CA

>think about all the motorcycles in the early part of the 20th century carrying sidecars while producing less horsepower (and perhaps torque) than any modern scooter. Granted, the motors were so huge for the output that they were probably understressed, but motor life wasn't great.