Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Dumb question--screwdrivers

Posts

Dumb question--screwdrivers

#1

Dumb question--screwdrivers

Wiley Horne--So. Calif.

>Hi Folks,

Need a little help. What screwdriver fits a European posi-drive screw? Looks like Philips, but even if so, there are Philips 1, 2, and 3. Or are there special Posi-Driv screwdrivers? Surely not Reed and Prince?

All help appreciated.

Wiley

Re: Dumb question--screwdrivers

#2

Why Wiley with a posi-drive screwdriver...

Scott Burr in Ben Lomond CA

>Duh! 8^)

Actually I have a posi-drive screwdriver. It came with a set of Craftsman screwdrivers I bought years ago. It has a red handle to tell it apart from the others. That's all I can tell you. Never seen a posi-drive screw myself.

Re: Dumb question--screwdrivers

#3

Jesper, Denmark

Re: Dumb question--screwdrivers

Jesper, Denmark

>There are special posidrive screwdrivers to fit the posidrive screws. They look like philips, but have a little different profile.

My opinion is that they are a pain in the neck, as it is nearly impossible to tell them apart. Fortunately, the trend here is to standardize on Torx screws - they work better than either philips, posidrive or the Canadian square drive, which is smaller and prone to over.torqueing the bit/screw.

Torx really has another problem as there are so many different sizes that it is difficult to tell two adjacent sizes apart.

Re: Dumb question--screwdrivers

#4

Pozidrive

Steve Elliott

>It's my understandin that there is only one tip size for Pozidrive. In smaller screws only a little of the tip contacts the screw, and on larger screws the tip goes in farther.

I've found Pozidrive screwdrivers at a local hardware store that carries a wide range of specialty tools. Haven't looked at Home Depot.

Re: Dumb question--screwdrivers

#5

Re: Pozidrive *LINK*

Hank Knight

>Wiley,

This pricy set from MSC Direct has posidrive bits. It looks like ther are at least 3 sizes:


Driver Set

Re: Dumb question--screwdrivers

#6

Jack Guzman from Maine

automotive

Jack Guzman from Maine

>I remember from the 80s when I worked in a mechanics shop. Snap-on,Mac,Matco and most other automotive tool sellers sell posidrive screwdrivers.I bought one back then but only used it a couple times.It was so hard to tell them apart I just ended up faking it with a regular phillips driver.---Jack

Re: Dumb question--screwdrivers

#7

Hmm ... Incomplete Link

Hank Knight

>Just type "posidrive" in the MSC search box and click "search." The MSC search function will bring up the set.

Re: Dumb question--screwdrivers

#8

I see 'em

Wiley Horne--So. Calif.

>Thanks Hank, I followed the link. MSC also sells individual drivers made in Germany by Wera. As Jesper indicated, they come in 5 sizes, but from the sets it looks like sizes 1 and 2 are the most-used.

I was running through design possibilities for a simple sticking board, and ended up somewhere in the decision tree wondering about posi-driv, because posi-driv screws were the only short, stout screws I could find that would solve a problem of screwing track down into 3/4" ply. Think I'll use glue instead......

What kinda glue is good for bedding aluminum track into baltic birch ply (<:)?

Wiley

Re: Dumb question--screwdrivers

#9

Re: I see 'em

Dan Donaldson

>If not getting wet, hide glue should work. It holds well enough to rip out pieces of glass ;-)

Re: Dumb question--screwdrivers

#10

Re: I see 'em

Hank Knight

>Wiley,

I've never bedded trac in BB Ply. I've bedded some in oak with West System epoxy and it worked great. It has never pulled out even though it handles considerable stress.

Hank

Re: Dumb question--screwdrivers

#12

A good epoxy...

Bob Hackett

>will work just fine.

Just remember to scuff and clean the aluminum track with solvent where you want it to bond.

Wax or clear packing tape will protect surfaces you don`t want epoxy on.

MB

Re: Dumb question--screwdrivers

#13

Good pic from McMaster-Carr

Alan DuBoff

>Wiley,

This is a good pic that I saw on the McMaster-Carr website.


Re: Dumb question--screwdrivers

#14

That would work, Scott *LINK*

Wiley Horne--So. Calif.

>I get a feeling you're used to doing mechanical design. Yours is a better idea than mine.

Here is the track (see link below). Goes into a dado 3/8" deep. The bolts slide along the track, as you can see. But it's not clear how much clearance there is under the sliding bolt head, to accommodate holddown screw heads etc. Cross-section is shown in 'View', but it's not dimensioned. However, just eyeballing it, you can see that a flat-head fastener and a shallow countersink would work. Thing is, in 3/4" ply, which I think is actually 1/64 or 1/32 less than 3/4", you have a little less than 3/8" of ply for the screw to get a bite into.

The reason for wanting a screw in there, is that a pair of these tracks is in the lower half--the base half-- of the sticking board. There is another board--the fence itself--which will ride on top with the bolts sticking through it and capped with 1/4"-20 knobs. So in a sense, tightening the bolts is trying to pull the track out of the lower board (yeah, I know the top board is pressing down, but it's the principle of the thing).

LV has fluted the outside of the channel to enhance the glue bond--so they must be thinking epoxy, or else some of our chem. engineers will be on their case about the nature of glue bonds.

I like your solution better than the one I was thinking about, because the screws are so short, and a machine screw will have more threads in play, and the threaded insert will provide better holding than the BB ply.

Epoxy is probably the best solution, but glue I can't wash off gives me the heebie-jeebies.

I'm pretty sure Stephen will advise that a little fresh garlic will prepare the metal for hide glue just fine (I didn't want to repeat the word 'aluminum' in Stephen's presence, so I said 'metal'.)

Thanks a lot, Wiley


Track (from Lee Valley)

Re: Dumb question--screwdrivers

#15

Re: Good pic from McMaster-Carr

Wiley Horne--So. Calif.

>Alan,

Thanks, that's a good diagram. That Frearson looks like what we used to call a Reed and Prince. Amazing how many systems are still in use. i hadn't heard of the 'clutch' one; gotta add that to the giant book of stuff I haven't heard of.

Thanks again,

Wiley

Re: Dumb question--screwdrivers

#16

Re: automotive

Wiley Horne--So. Calif.

>jack,

Did Phillips cam out like it's s'posed to?

Wiley

Re: Dumb question--screwdrivers

#17

Funny thing

Dan Donaldson

>I was going to make up a book of things that I had never heard of or didn't know how to do. The only problem was that I wasn't sure how many pages I would need. (other than a lot ) ;-)

Ducking and running ;-))

Re: Dumb question--screwdrivers

#18

Jim DeLaney, Austintown, Ohio

Re: Good pic from McMaster-Carr

Jim DeLaney, Austintown, Ohio

>GM used to (1960's or so)) use Clutch drive screws on their door latches. Don't know if/when they stopped.

Jim D.

Re: Dumb question--screwdrivers

#19

In regards to the Frearson, I was thinking...

Alan DuBoff

>Wiley,

When I looked at that I immediately said to myself, "self, a Frearson driver would most likely work on a Phillips, but not the other way around...". ;-)

Although that Pozidrive looks like you would be SOL without the proper driver...not sure how you could get that unscrewed without one...:-/

Re: Dumb question--screwdrivers

#20

Actually maybe a Frearson would work...

Alan DuBoff

>Wiley,

Actually the Frearson looks like it would work in the Pozidrive also...maybe it's the universal driver to get! *wink*

Re: Dumb question--screwdrivers

#21

Conundrum

Wiley Horne--So. Calif.

>One of the singularly important things to know, is knowing what you don't know (<:).

Wiley

Re: Dumb question--screwdrivers

#22

cluthe driver

Bob Demers

>In the early 70s, while I was working in a Radio-TV shop in Montreal, i came accross once into this unbeknown to me fastener, and went out to buy the proper screwdriver. Forget trying to undo that fastener with anything else!

So I bought myself this brand new Excelite driver, used it once, and never ever came across that fastener type ever again!

Thats why, after all these years, that one single screwdriver still look like new, only used once :-)

Just think, years from now, it will become a pristine, rarely seen handtool, worth a fortune...youpee im rich!

Too bad it didnt came in a box, it would be worth more :-)

Bob


img

Re: Dumb question--screwdrivers

#23

Re: Actually maybe a Frearson would work...

Bob Demers

>If I recall correctly, the Reed and Prince doesnt have the same conical angle as the Phillips, hence nothing strip a Phillips fastener faster than using the approximate sized Reed & Prince and trying to compensate for cam out by using over pressure and buggering up the poor thing, not to mention it quickly ruin the driver tip.

Bob, whose one of his most annoying pet peeve is finding damaged screw heads in assemblies. If you damaged the poor thing, replace it and use the right driver for Pete sake!

Re: Dumb question--screwdrivers

#24

Re: Conundrum

Dan Donaldson

>But then I would know it and.... or maybe I could add it to the list of.., or... HMMMMMMMMMMMMMMMMMMM. ;-)

Re: Dumb question--screwdrivers

#25

Tangential issue

Bill Houghton, Sebastopol, CA

>Are you grooving the ply to accept the track?

I had a bad experience once with setting track into commercial solid core door stock (one of my standbys for workbenches). These doors, like plywood, are a balanced construction, and cutting a groove in one face resulted in the door bowing up on the groove side during the next rainy season. The core wood could expand on that side, but not the other.

I've never tried it in baltic birch ply - I don't know if similar issues would exist.