Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Anybody ever use one of these blades? *LINK*

Posts

Re: Anybody ever use one of these blades? *LINK*

#27

Re: All ready tried it Wiley...

Derek Cohen (in Perth, Australia)

>For shooting end grain, the mouth size is not relevant. So, as long as the blade is stiff enough, you can use a thin one that leaves a wide mouth. One the thickness of the original Stanley will work very satisfactorally, especially when helped by a thick cap iron (hence my combination of Smoothcut blade and Clifton Stayset ... I vaguely recall that Joel has the same set up as mine).

Regards from Perth

Derek

Re: Anybody ever use one of these blades? *LINK*

#28

Re: Anybody ever use one of these blades?

James Watriss

>Tell you what, Scott, I'll poke around the shop on Friday and see if I have any of my old stanley blades kicking around. I may have an old-school laminated version, type 10-13 or so, that may work for you.

Re: Anybody ever use one of these blades? *LINK*

#29

Re: On D2 ..

Tom Colligan

>Derek, where may one purchase a D2 blade that is 5/16" thick for a self made woody? TIA, Tom.

Re: Anybody ever use one of these blades? *LINK*

#30

or 5.29/64"

Bill Houghton, Sebastopol, CA

>not that you're supposed to do decimals in the numerator of fractions...but that seemed more helpful than "roughly 21/256," since there aren't a lot of rules that measure in 256ths.

Re: Anybody ever use one of these blades? *LINK*

#32

Re: or same as a common Stanley blade?

Wiley Horne--So. Calif.

>My Type 16 from the 1930s, Stanley No. 6, 2-3/8" iron mic's at 0.0750", with variation in the 'tenths'.

5/64" = 0.078".

2.1mm ~ 0.083".

So if Derek's 0.083" blade fits OK, then the 5/64" blade should as well. Also, 5/64" is within lapping distance of my No. 6 iron.

Wiley

Re: Anybody ever use one of these blades? *LINK*

#36

I'm gonna use a Hock cap iron...

Scott Burr in Ben Lomond CA

>That way I won't need any super glue to save my toes. 8^)

Re: Anybody ever use one of these blades? *LINK*

#37

Wouldn't their punishment be self-evident?

Bruce, a MN Galoot

>

Re: Anybody ever use one of these blades? *LINK*

#38

Yeah, but my pay grade is too low to inflict it.

Pam Niedermayer, Austin, TX

>

Re: Anybody ever use one of these blades? *LINK*

#39

Re: Anybody ever use one of these blades?

ThomD

>I used to use lots of those blades, both versions from LV, and from Masterpiece tools, possibly others. Always thought they were great. Thin blade size did not seem a problem. There is the Krenov argument that they are stiffer, which is as least a source of comfort when one is using them.

Re: Anybody ever use one of these blades? *LINK*

#40

Re: Think I'm with Ellis on this one...

ThomD

>Blue Steel in the case of these kinds of blades probably has more to do with the fact they are more resistant to dry grinding. At best it will be actual Hitachi steel, more likely just something similar. I always liked mine (20 years ago) because they would fit any sharpening jig, which was cool for regrinding, and they held an edge for ever, and they were fairly easy to sharpen.

I am all for simple O1 blades like the Hock, have a lot of them, but they don't confer much super blade performance, and I prefer them in easy to cycle planes like wooden hand planes. Most of my BS replacement blades went into the Records LV was selling at the time, and any excuse to not have to take a blade out of one of those was welcome. :)

Re: Anybody ever use one of these blades? *LINK*

#41

Found one..

James Watriss

>It's an oldie but goodie.

It's not tuned up, and there's a slight bit of pitting you'll want to grind away. But it's yours if you want it.