Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

The ULTIMATE dovetail project...

Posts

Re: The ULTIMATE dovetail project...

#26

Re: Watched Dick Proenneke?

ThomD

>It runs on PBS periodically, but I have never managed to catch it...

Re: The ULTIMATE dovetail project...

#27

Re: My favorite pullsaw

ThomD

>is a chainsaw. I have a slew of japanese saws, but only a few are all that big, one resaw, and a log saw. Projects for me devide into for fun, and production projects. When it comes to blowing out wood I break out the Stihl 090.

Re: The ULTIMATE dovetail project...

#28

It's a great dvd, I highly recommend it.  *LINK*

Pam Niedermayer, Austin, TX

>


Alone in the Wilderness

Re: The ULTIMATE dovetail project...

#29

Re: My favorite pullsaw

Alan DuBoff

>Thom,

Yeah, I have a couple chainsaws, and they work fine. This pull saw is for final fitting at the shoulder. I could use a hand plane also, but I have to move the log out a bit. Even a chisel would work. But the pull saw will allow it to be done while the log is in place during fitting.

Either way, this is not a task for any type of power, it is all about getting the joint to fit properly by fitting it by hand.

Regards,

Alan

Re: The ULTIMATE dovetail project...

#30

Re: Chuyemon ryoba--now that you mention Manny...

wilbur

>I can't speak to the Chuyemon ryobas directly since I haven't used one, but Manny told me exactly the same thing regarding these saws, and that after Mitsukawa sharpened and set them up, they did quite well. I would trust his experience.

Congratulations on the baby, Manny, if you're reading this!

Re: The ULTIMATE dovetail project...

#31

Re: Chuyemon ryoba--now that you mention Manny... *LINK*

Alan DuBoff

>Wilbur,

Manny know about as much about Japanese tools as anyone I know, and what he doesn't know he can usually find out. I'm going to try and get together with him possibly in another week or two, just wanted to give him some breathing room with the new baby...Babies have a way of throwing a curve ball on the parents for a couple weeks...at least I know that both of mine did...

He also mentioned for the task I want it for, the Chuyemon flexes just a bit more, and I need to clear the log with the handle, so he felt it would work better for that task, over the Mitsukawa.

That said, I noticed there was a "Mitsukawa Brand Handmade Ryoba Saw:

180mm Ryoba saw with 0.34mm kerf." listed on the Hida site, and I asked Manny if that could possibly be handmade, and he said no. He wasn't sure why it was listed like that and said they are usually pretty good about that. That doesn't seem right though...too cheap for a handmade Japanese saw...first one in the second row ($78).

Regards,

Alan


Hida's Saw Page

Re: The ULTIMATE dovetail project...

#32

This is basically a carpentry job

Pam Niedermayer, Austin, TX

>Therefore, there'd be no problem and possibly some advantages to using a machine made saw. Sure a good thing to be able to pop in a replacement blade at a moment's notice. My experience is that they last a long time, too. And, again, there's no big reason for using a ryoba in this case, handmade or not.

Pam

Re: The ULTIMATE dovetail project...

#33

Speak'n of pull saws....

Marv

>A two man crosscut saw is a pull saw. Not my favorite pull saw though. It cuts both directions but there has to be another puller on the other end. Most of us old dudes know about these saws because we used them for cutting firewood when we were kids, lots of firewood. Me at 7 with my older brother at age 11. We knew what hard work was. This was long before chain saws came along.

Marv

Re: The ULTIMATE dovetail project...

#34

I'm wondering how the ancients did it...

Marv

>Perhaps using a sharp obsidian rock would work well along with fire. Char the joints and just scrape off the burnt stuff. Opps, forgot about EPA and pollution. Think green.

Re: The ULTIMATE dovetail project...

#35

Still a pretty good way to make a canoe.

Pam Niedermayer, Austin, TX

>

Re: The ULTIMATE dovetail project...

#36

Yes, but only if one has no other means of doing i

Marv

>