Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Hand Drills

Posts

Re: Hand Drills

#26

Re: OT....Laptops...

Pam Niedermayer, Austin, TX

>The keyboards are usually missing some keys, like a number pad, page up and down, etc.; but I haven't noticed that the actual keys are smaller.

For a long, long time I was a traveling consultant, so a laptop was essential. I remember well the few trips I took with one of the early Macs, aaaaarrrggghhhh. And now it's very handy to take a laptop to class, to work in a coffee chop, etc.

Pam

Re: Hand Drills

#27

Re: Hand Drills

David Brown

>Wow, folks, this was great. I see that my fears are probably unfounded. You know there is so much concern about tolerances with power tools: how flat is your table saw top, is the blade aligned to less than a thou, how much tension is on your band saw, what is the run out on your drill press, etc. So I thought old hand tools might suffer from this. Especially considering that flatness in the sole of a plane seems to affect how thin a shaving you can take.

What I was mostly wondering was if you have a 3/16" bit and you drill a hole, does it come out 3/16" in diameter. What I'm hearing is yes, it generally does.

So I'll probably add this to my I want one list. Maybe someday I'll have the money for one.

Thanks, everyone.

--Dave

Re: Hand Drills

#28

Re: What is runout?

David Brown

>I had no idea. It is absolutely amazing. Maybe I'll substitute this for "we can put a man on the moon, but we can't...". For example, our fridge's ice dispenser never fails to spit out an ice cube just as you are removing your glass. And I'll say, we can put a man on the moon, but we can't make a better ice dispenser. Now I can say, we can make ball bearings with runout measured in microns, but we can't make a better ice dispenser.

It's good to have these sorts of things ready in your mind :)

--Dave

Re: Hand Drills

#29

Re: why does this work?

Philip Duffy

>If you watch the disparity in the circular motion of the tip of the bit and lightly tap at a random sequence you will see that the disparity gets better, provided you do not hammer past the centerline of the axis. So, that is the tricky part; where is the centerline of the bit when straight? I believe that there is considerable luck in getting it right with only one "tap", but that likelihood increases rapidly with each tap of the hammer. Try it on other bent items and you will see it magically! Philip

Re: Hand Drills

#30

Re: why does this work?

ThomD

>It works because the piece is off center and the outer diameter of the circulating mass is going to be the part that is furthest from the center. Idealy the part is moving at a tempo, or suffient speed that you can't get past it to hit the inermost part of it. So all your taps fall on the most eccentric part of the thing. If it is free to move it should end up better centered. It does work and doesn't require any particular skill. On the other hand it should be of some concern that the thing isn't held all that firmly.

This works if you have something askew. If what you have in your chuck is an object that is cetered but has high and low points, then you will tend to knock it off center. An example of that could be a bowl. They start out concentric, but sometimes they pic up an oval from being dried, or shaking out water, or releasing internal stress. If you tap on that, it might true up or it might knock off center since an eliptical piece that is centered will have high and low points.

A master gunsmith might use a center drill in the first place.

An interesting tool is an edge or center finder. It's a rod with a poited or cylindrical shape. The end is separate from the shank, but perfectly continuous with it, all ground at once. It is mounted with a spring so it can be off center, or centered. When the drill press is fired up it will center, then when you bring an object up to the spining edge the point it touches, it will visibly jump out of center. Allows one to relate the edge of a known object centered in the chuck to a workpiece. Has a few other related uses.

Re: Hand Drills

#31

Re: Hand Drills

paul womack

>most jigs are probably a lot looser than the runout in most drills.

Agreed.

I use the "jig" (it seems wrong to call a drilled piece of scrap metal a jig!) to avoid the drill bit following the grain when using a hand drill, which is a much larger source of errors than runout.

BugBear

Re: Hand Drills

#32

Re: Hand Drills

paul womack

>I suspect it's not so much a tap, as an object with fairly large insertia - the hammer head.

I would guess the mechanism is much like that used by horologists to centre an workpiece, to very fine limits, in a wax chuck.

BugBear

Re: Hand Drills

#33

thanks

Bill Tindall, E.TN

>While the explanations were clear, it remains to be seen if I can master the technique. As I recall, Alan tapped the out-of-center spindle rapidly as it spun, consistent with what the explanations would require.

Re: Hand Drills

#34

Re: OT....Laptops...

Marv....... Northern California Lake Co.

>Pam,

I haven't looked closely at a laptop in years. I'm sure they have been improved immensely since I last looked. Do they still come with that stupid little red button in the middle of the keyboard that was supposed to be mistaken for a mouse?

I used to subscribe to several magazines and kept up on all the latest computer junk. I finally developed an attitude like I have toward cars....a necassary evil. However, unfortunately, the attitude didn't come about until I had accumulated shelves full of useless software. (that I still have, by the way) Gawd, I wish I had all the money I wasted on computers and related crap.

Marv

Re: Hand Drills

#35

Re: Nah...don't work,,,,

Marv....... Northern California Lake Co.

>Todd,

I love the sour-casm....LOL

This is probably a stupid question, but are you familiar with the Millers Falls No.97 breast drill? NOW THAT's a HAND DRILL

Marv

Re: Hand Drills

#36

And there wasn't . . .

steve mackay

>popcorn 'till microwave ovens.

Re: Hand Drills

#37

Drill Bits

Phil Joines Krum,Tx

>I got a set of midprice brad point bits that were ground off center. They would all drill oversize holes. Sent them back.

Re: Hand Drills

#38

Re: OT....Laptops...

Pam Niedermayer, Austin, TX

>I don't know, that was an IBM PC thing. I do know (we were IBM partners for a long time, but only for the server technology) that a lot of users loved it.

As to wasted money, most of mine has been spent on software.

I've never been real interested in hardware, nor magazines, so I never followed the computer world like you did. Maybe InfoWorld, which was more of a professional rag, and MacTech.

Pam

Re: Hand Drills

#39

Re: Chuckie's in love

ThomD

>Nothing really to do with the thread or keeping drilling on center, but I am a convert to chucking reamers where accurate hole shapes and diameters are concerned. They also make CRs that are a thou oversize, which are great for all those situations where the perfect dowel and the perfect hole are too perfect. They are a metalworking tool but cut wood nicely, and they are cheap enough in small sizes.

Re: Hand Drills

#40

Re: thanks

ThomD

>Good luck with it. If the rotating thing is the right kind, and the fixturing is capable of movement, it is pretty much automatic. Otherwise I probably try something else. Sometimes laying the hammer shaft onto the spinning object, or resting the face of the head will tell you when it is centered, to the extent it isn't otherwise obvious.

Re: Hand Drills

#41

Re: Nah...don't work,,,,

Joe Rogers, Northern Virginia

>Yeah got one in nice shape on the Bay. Haven't found a job for it yet but it is way high on the gizmosity scale.

Joe

Re: Hand Drills

#42

Millers Falls No.97

Marv....... Northern California Lake Co.

>Hi Joe,

Those things were built like a tank. They weigh 8 pounds with the extra large breast plate attached. I have five of them. I kept buying them until I finally got one that looks almost like new.

For those who aren't familiar with this Mother of all breast drills, it's the one, front center in the picture.

Marv


img

Re: Hand Drills

#43

Re: Millers Falls No.97

Joe Rogers, Northern Virginia

>Nice Marv. Mine is a little scruffier than yours, but it does have a partial decal on the main drive gear.

JR

Re: Hand Drills

#44

Sure you have enough drills, Marv?

Bill Houghton, Sebastopol, CA

>Not that I am in a position to gloat about how few tools I have...

Re: Hand Drills

#45

Re: Sure you have enough drills, Marv?

Marv....... Northern California Lake Co.

>Hi Bill,

My wife calls me a tool whore. I have no idea what she means by that.

I haven't bought a drill in quite a long time. I kinda jump from one tool to another when it comes to collecting. Saws are now the thing. My problem though, is, I don't have enough money to be a serious collector.

I'm thinking about selling my pickup.

Marv

Re: Hand Drills

#46

Re: Sure you have enough drills, Marv?

Joe Rogers, Northern Virginia

>If ya sell the pickup you will have a devil of a time when you start collecting Emmerts. Lifting them up over the trunk lip is tough.

Joe

Re: Hand Drills

#47

Re: Sure you have enough drills, Marv?

Marv....... Northern California Lake Co.

>The only reason I haven't bought an Emmert is because I can't pick it up and I don't have a forklift :>

Marv