Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Got my tools somewhat organized

Posts

Got my tools somewhat organized

#1

Got my tools somewhat organized

wilbur

>My bench building project went on hiatus when I realized I had made a miscalculation on the legs. It's just as well -- this hiccup gave me a chance to get my shop organized a little. My previous tool storage system consisted of cardboard boxes on the floor. Sometimes I would skip the cardboard box.

Besides, as I get into making the base, I realized that I would need more tools than I needed for the top. Looking back, it seems like the only tools I needed to glue up the top were a jack plane, a jointer plane, a square, a pencil, and clamps. For the mortise and tenon joints in the base, I'll need a lot more than that.

So here's a picture of what I did. I drilled holes in the walls of my basement and attached 2x4s with the flat side against the wall with concrete wedge anchors. I placed and shimmed pressure treated 2x4s on the floor of the basement so that the 2x4s on the wall were resting on the pressure treated 2x4s on the ground. Then I attached pine boards to the 2x4s, and then hung the tools on the pine board.


This clearly is going to be a work in progress for quite a while. I'm making a guess as to which tools I use most often, and tried to put them in the most convenient spot. I'm already second guessing the rack I made for my saws, as I have to lift the saws straight up which means that I lose storage space above the saws. If you look closely, you can see how I screwed up the chisel rack, as I didn't take into account that for my chisels, the diameter of the handle gets bigger as the chisel gets wider. I also want to redo the clamp rack, as the bottoms of the clamps sway back and forth a bit. I did make sure that all the various tool holding devices are just screwed to the pine boards, so I can move/replace them as needed.


But now I can start working on the base of my workbench!

Re: Got my tools somewhat organized

#2

Well ya know,,,

Scott Burr in Ben Lomond, CA

>It's better to build the base first. That way you have a place to work on the top. Nice looking re-org you have going there, and nice chisels and saws toooo!

Re: Got my tools somewhat organized

#3

Re: Got my tools somewhat organized

James Watriss

>I think a long as you keep your most-used saws to the left, the saw rack isn't so bad... besides, it's not like you have to clear something like, say... that HUGE wooden router plane you have there. (that thing's really cool...) And the chisel rack is cool, and it works, even if it doesn't take different handle sizes into account.

Tool boards are almost always an exercise in trial and error. Unfortunately, not all of us can be H.O. Studley.

Re: Got my tools somewhat organized

#4

Re: Got my tools somewhat organized

Pam Niedermayer, Austin, TX

>I really like the magnetic tool bars for the Japanese saws, work great, modular. It crossed my mind to be concerned about whether the magnetism would adversely affect the saws, but I got over that. :)

Pam

Re: Got my tools somewhat organized

#5

Re: Got my tools somewhat organized

Kevin Adams

>Hi Wilbur--

I might have done the unthinkable, but for my everyday (replaceable blade) saws I just drilled a small hole in my saw handles and hung them from a finish nail. It's real simple and I can't see the harm. Now my handmade saws...I keep them protected in a canvas holder. Which brings up an interesting question: are these saws meant to be hung in order to keep them in proper tension or is it OK to keep them stored in the canvas holder?

BTW, I remember Wiley showing photos of his tool storage area and he had a neat saw holder where the saw blade was just in a kerf cut in a 1x board. The handle keeps it resting on the holder. You might check the archives or maybe Wiley will chime in.

The shop is looking good and like everyone said, tool holders seem to always be a work-in-progress. That's why keeping it simple on wooden boards like you used seems to work best.

Take care,

Kevin

Re: Got my tools somewhat organized

#6

Re: Got my tools somewhat organized

Patrick Gibbons, Katy, TX

>I've been trying to do the same thing. I've worked from the concept that I use my tools in groups and have tried to establish stations around the shop. I put my saws, braces and eggbeaters together, lathe tools and lathe, bench and bench planes, misc. tools on pegboard such as wrenches, pliers, hammers, etc., I'm contemplating building a chest a la Cherubini for chisels, layout and other planes. Oh yea, sharpening is a separate station too.

For the saws I've built, or am building, an open saw case for the rip and xcut saws and my back saws are arranged on an octogon mounted on a lazy susan. The one I've built so far holds eight back saws.

I've taken a cue from Chris Schwartz and started using Shaker pegs. Maybe I'll post pictures when I'm finished. That is if I'm still alive. I maybe only have a good 30 years at most to live. That doesn't give me enough time to finish unless I rush some things.

Re: Got my tools somewhat organized

#7

Re: Well ya know,,,

wilbur

>In this case, it's better to build the top first. All I needed for support to build the top was a pair of sawhorses. For the joinery needed for the base, a real worksurface will be really helpful, so now I have somewhere to do that work. I'd hate to try to do the mortise and tenon joints on sawhorses.

Also, this is a Roubo type bench, so the legs are going to be mortised directly into the top, and I didn't know exactly how wide the top was going to be when I finished. Now I'll be able to exactly size the base to the top.

Re: Got my tools somewhat organized

#8

"This clearly is going to be a work in progress.."

Bill Houghton, Sebastopol, CA

>This coming summer, we'll celebrate our 35th year in this house. With luck, I'll have made some progress on tool storage (sorry, Patrick G).

My biggest problem has been my apparently incurable attractiveness to tools, which keep following me home from garage sales (and, for a while there when I was flush with money from my consulting gig, eBay); and, once they're here, I just can't turn the poor little things out in the cold. So the needs keep evolving. I recall, some years back, that my plane storage consisted of two shelves set between the studs in my shop (24" on center more or less, so 22" of shelf, 6" wide). It's now exceeded one bay of my under-workbench storage, 12" wide, 24" deep, 36" high, three shelves and one drawer for the little planes - and no room there for the Stanley 45 and 55, Veritas plow, extra jack, recently acquired Stanley 81 (I think that's all that are stored elsewhere).

But I concur with others: make your storage modular and flexible, and recognize that, even if you have more self-control than I do, it'll take a while for you to learn the optimal layout.

Re: Got my tools somewhat organized

#9

Incidentally

Bill Houghton, Sebastopol, CA

>Is that a window well visible above the tool board? If it is, it's not your emergency exit window, is it? It looks like you're blocking it slightly.

Re: Got my tools somewhat organized

#10

Re: Incidentally

wilbur

>Hi Bill,

That is a window well. It's long been blocked off. Prior to us buying the house, the part of the house on the other side of that window was landscaped, and the window well was buried in the process. In fact, there's plywood covering the outside of the window.

I have a Bilco door that leads directly to the shop on the opposite wall, so I think I'm covered for an emergency exit. :@)

Re: Got my tools somewhat organized

#11

OT - Are you in a termite-y area?

Bill Houghton, Sebastopol, CA

>Plywood with ground contact's not such a good idea, unless it's been treated for ground contact. I know there are parts of NJ with pretty vigorous termites (don't you folks have Formosan termites back there?).

I've been a little sloppy at times, leaving wood on the ground, and found some nests when I cleaned it up. When we finished the recent insulate-the-floor project, I spent a day cleaning out the accumulated, um, stuff (almost all of it roots or things that predated my responsibility for the house) in the crawl space, hoping to discourage termites there.

Re: Got my tools somewhat organized

#12

Re: OT - Are you in a termite-y area?

wilbur

>That piece of plywood is covered with at least 18 inches of dirt and large rocks, so digging it up would be quite the endeavor. :@)

As best as I can figure, it's been like that for close to 10 years, so if any termites were going to show up, I imagine that they would have done so by now.

Re: Got my tools somewhat organized

#13

Re: Got my tools somewhat organized

Manny

>It's always best to hang them especially if used infrequently. Drilling a hole in the handle is a good way of hanging them.

I haven't had any issues with my handmade ryobas being stored in these leather holders and stored in my field box for long periods of time. However, I remove my dozuki from the case after I return and put them on a wall rack. I learned my lesson a while back not to leave my dozuki in the cases week after week. On a handmade dozuki the blade is very thin and the spine is somewhat malleable. Ryoba blades tend to be much thicker, especially those made by Yataiki. So, ryoba tend to spring back into shape (Not always though) Over time the dozuki saw spine will conform to a shape dictated by whatever forces are acting on it; like the weight of the other saws in the case, the weight of the handle hanging over an edge, laying the thing on an uneven surface or whatever. Basically gravity doing its thing. The saw can bend on the spine or close to the handle on the weld between the hard metal blade and soft metal tang. Bending it back into place can be easy or it can worsen the problem. So, it's best to avoid this altogether by hanging them when you don't expect to use them for a while or don't plan to take them anywhere outside your shop.


img

Re: Got my tools somewhat organized

#14

Hanging dozuki

Manny

>Here is how I hang my dozuki.


img

Re: Got my tools somewhat organized

#15

Re: Hanging dozuki

Kevin Adams

>Thanks, Manny, I guess I need to see how my saws are doing...hopefully, no issues.

Kevin

Re: Got my tools somewhat organized

#16

Re: Hanging dozuki *LINK*

Wiley Horne--So. Calif.

>Hi Folks,

Mine are in slots, like Manny's (probably where I got the idea), but the slots are angled at 45 degrees, so as to keep the blade projection closer to the wall. I have larger saws (375mm-450mm) with the handle drilled and hung on nails, just as Wilbur describes.

Manny's right--if dozukis are carefully supported and separated in a secure place, you're OK, but if they are casually stored, a zillion little bad things can happen. All in all, hung in tension is best.

Wiley


The one time Wiley's bench was cleaned up

Re: Got my tools somewhat organized

#17

Re: Hanging dozuki

Kevin Adams

>BTW, how about another photo or two of your tool box? Sure looks nice.

Thanks.

Kevin

Re: Got my tools somewhat organized

#18

You moved the shop off the porch?

Pam Niedermayer, Austin, TX

>

Re: Got my tools somewhat organized

#19

Re: You moved the shop off the porch?

Wiley Horne--So. Calif.

>HI Pam,

Same old same old. It's at the far end of a long narrow utility porch. I closed off the end windows against the western sun, which is brutal here in the summer. Old picture, there are more saws now.

Thanks for asking, Wiley

Re: Got my tools somewhat organized

#20

More saws?

wilbur

>More saws? Where the heck did you put them? :@)

By the way, did you ever get a Heiji saw? If so, how did you like it?

Re: Got my tools somewhat organized

#21

Re: Got my tools somewhat organized

ThomD

>For saws, I use a rack similar to yours but it is about 3 inches deep, oversized but still snug kerfs are cut into this board and the saws are slotted in. You can get at least twice the number of saw, and the saws pull straight out and there isn't any resistence or mechanical sounds as with magenets. One would think the finger which hold the saws, and are crossgrain would snap off, but over the years no problems of any kind.

I use tapered holes for my chisels. Sooner or later one will fall off the pegs, which is pretty much ok if you have wooden floors, but I don't. To make the holes I drill holes through some wood, then I ream those with a metal reamer that LV sells. Chisels are held at the ferrule, and a little lift will remove them directly to the front. You can also store a lot of chisels this way, though one has to be carefull not to crowd them overly obove the handles.

I use quite a few of the racks you have your chisels on, but for the most part I use them for rarely used chisels and stuff like, ones I made myself (easily restored by me), and files.

The picture shows about a third of my chisels and there is a whole other rack of my saws. I just like this shot because it shows all the different styles of rack I use.


img

Re: Got my tools somewhat organized

#22

If they do,

Bill Houghton, Sebastopol, CA

>you'll have your very own termite farm, right there in the window.

Re: Got my tools somewhat organized

#23

If you wanted to spend time rather than $$

Bill Houghton, Sebastopol, CA

>you could probably find a plumber's reamer at any decent flea market for $1 or so, rather than Lee Valley's.

Good idea, that, Thom.

Re: Got my tools somewhat organized

#24

Re: Got my tools somewhat organized

Pam Niedermayer, Austin, TX

>here isn't any resistence or mechanical sounds as with magenets

Yeah, that's a bit bothersome, and I pull them off gingerly to avoid any chance of bends and kinks. But I love the height of my tool bars, about waist high, so I can reach out without standing on my tiptoes and pull off a saw.

Pam

Re: Got my tools somewhat organized

#25

Heiji saw

Wiley Horne--So. Calif.

>Wilbur,

Saws are so great, I just can't stop. They've spilled over into the living room--I like having them near.

I am having some grief about Yataiki-san's retirement and physical weakening. The man is worthy of the highest honors in Japan. If you get a chance ever to acquire a Yataiki saw, buy it at whatever the asking price is. Or tell me about it--thinking particularly of dozukis or katabas.

Yes, I have had a Heiji yokobiki (single edge crosscut), 200mm, for several months now. It is really a fine saw. Super sharp, and nice taper. Cost is $500-550. He can't get rich at that price, because of the work involved. I am mulling over a 270mm tatebiki now. Will definitely get more from Heiji, and highly recommend him based on the one saw I have.

Kevin may have a Heiji saw--if so, perhaps he could comment?

Wiley