Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

A manly chisel!

Posts

A manly chisel!

#1

A manly chisel!

Bill Tindall, E.TN

>I tossed that out for Pam....I must admit that a more dainty Japanese style would be nicer for the tasks but this one cost but $5 and 45 minutes of work. Recall that I am exceptionally frugal.

Someone brought a box of old tools to the club meeting and in it was what became this chisel. It is the sort of thing we used to weld to a piece of 1" pipe and chop holes in the ice for fishing. Anyway this thing was sharpened as a lathe skew chisel. The manufacturer is Riverside, a name I never heard of, but it is excellent steel.

I have been needing a wide flat chisel to use with guides for paring things. For example, to make the miters in this cock bead I shave them using a 45 degree guide black. Ditto for sliding dovetails with a 14 degree guide block. A wide flat chisel gives good register on the guide block.

First I ground away the skew angle and then established a bevel using a 36 grit wheel. I suppose because of the mass there was no tendency for the edge to heat. Also I was using a very friable wheel. Next I straightened the edge with a coarse fixed diamond stone. It took but a few strokes. The edge was refined with a fine diamond stone followed by the usual honing. I bought this thing because it had no rust. It was a simple matter to flatten the back with the fine diamond stone.

The tang is enormous. I drilled stepped holes in the handle, starting with 1/4" and ending up 1/2". I then sawed a slot in the part of the handle under the brass ferrule to further accommodate the widening tang. I was not confident of the handling so I used a scrap of sap cherry. It turned out comfortable, so I won't change it any time soon. I like this handle style. It works well and had good balance for what could have been its unwieldy size.


img

Re: A manly chisel!

#2

That's a heck of a paring chisel

Bill Houghton, Sebastopol, CA

>Years ago, I picked up a paring chisel about that width, but more paring-chisel-thin. I agree that a wide chisel is terrific for some paring work, but I sure would rather drop mine edge down that yours. My shoes could stop mine - I'm not sure a concrete floor would stop yours.

Re: A manly chisel!

#3

A manly chisel question?

Stephen Shepherd in the State of Deseret

>Arn't turning chisels not as hard as bench chisels?

Stephen

Re: A manly chisel!

#4

lathe vs bench tools

Bill Tindall, E.TN

>Modern lathe tools are all high performance tool steels, selected for abrasion resistance and heat treated at the high end of their hardness capability. In a recent class it was quoted how few minutes it takes to move the lathe tool a mile through the wood at 3000 rpm, a typical turning speed. Abrasion resistance is the most important factor in modern lathe tools. One typically makes miles of shavings between sharpenings.

Of course old lathe tools were carbon steel. I have a few and I have no evidence that they are hardened any different than plane irons. But they sure get dull quicker.

I don't know what the tool in question was originally. I never saw a lathe skew 2" wide. Furthermore, it is tapered like a typical bench chisel, 1/8" thick at the bevel to 1/4" thick at the tang. So I suspect it began life as a chisel, and now it is back home. The steel is very good. I have ground enough to tell good stuff from softer steel. It took a long time to grind off the skew point and establish the bevel. It is holding an edge typical of a good chisel.

Re: A manly chisel!

#5

Re: lathe vs bench tools

Todd O. Cronkhite Maine Native Presently Away

>Good show on resuing that chisel and putting back into the battle Bill. It's a beauty for sure, and for 5 bucks I'd of snapped it up also. It's hard not to be a sucker for a big chisel. ;~)

I have to wonder tho if not you'd of been better off leaving the skewed cutting edge on it, but I suppose if you need to you can always skew the entire chisel if you need too. Either way, I'm sure it now suits your needs and that's all that matters.

Good job on that handle as well. I have a piece of what was fire wood that I turned round in btween the centers of my lathe now that is going to be a handle for IIRC and W. Butcher chisel that is 2" wide and has a tapered tang. I was gonna work on it today but didn't get to it. :~( Perhaps tomorrow. :~) I have some 3/4' copper tubing that I was going to use for a ferrule, but I think it too small, so I'll have to scrounge around in my junk and see if I can find something bigger.

T.O.

Re: A manly chisel!

#6

Bill, FYI

Patrick Gibbons, Katy, TX

>Riverside, I think, is a Montgomery Ward brand. When I was young, Monkey Wards still sold their own brand of motorcycles, Riverside, and I believe they used the brand name on other products.

Re: A manly chisel!

#7

OK Bill, How big is it?

Scott Burr in Ben Lomond, CA

>

Re: A manly chisel!

#8

Re: lathe vs bench tools

Robin Corell in Atascadero CA

>The tang on that is the same as all of my turning tools and unlike all of my bench chisels. I have an old Greenlee 1 1/2" roughing gouge that is tapered in thickness as well as a Winstead Edge 2" square nosed sraper that is also tapered. my guess is that it started life as a lathe tool.

Robin