Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

First backsaw with split nuts!

Posts

First backsaw with split nuts!

#1

First backsaw with split nuts!

Bill Houghton, Sebastopol, CA

>That's the good news, part 1.

Good news, part 2 was that it cost me 50 cents.

The bad news is that there's just a bit of rust on it.

In California, it's an old tool if it's older than 1900. So I'm kinda stoked to have found a saw with split nuts, even if it may be too far gone to resurrect.

Kind of sad - it belonged to the grandfather of the woman who was running the estate sale, but, as she put it, it got kind of rusty. I promised I'd try to honor her granddad in fixing it up.


img

Re: First backsaw with split nuts!

#2

The medallion

Bill Houghton, Sebastopol, CA

>The spine says something about "A. R---ing," with "Cast Steel" under that. The medallion's fuzzily pictured below (the writing says "Warranted Superior" - not very helpful). Any idea who made it?


img

Re: First backsaw with split nuts!

#3

And my first bedrock plane, too

Bill Houghton, Sebastopol, CA

>Missing a few parts...

This was $1 - I think I might try Todd Hughes' sell-the-parts strategy, rather than wait for the rest of the parts to appear.


img

Re: First backsaw with split nuts!

#4

The medallion - a little more information

Bill Houghton, Sebastopol, CA

>I meant to mention: the picture on the medallion appears to be a knight (probably not Steve) on a horse - unless it's a seahorse. Behind the knight, there appears to be another knight.

Re: First backsaw with split nuts!

#5

Re: The medallion

Ray Gardiner

>Hi Bill,

Based on the limited info, I am guessing it's "A Rosling" which is

trademark used by J Beardshaw & Sons Ltd. They were in business from 1825 through to 1961, so dating is a bit problematic, going by style I would think pre 1900.

It would be nice to see it cleaned up and restored.

Regards

Ray

Re: First backsaw with split nuts!

#6

Re: And my first bedrock plane, too

Kevin French

>Bill I see you've been digg'n WAY into the rust pile.

Re: First backsaw with split nuts!

#8

Thanks, Ray

Bill Houghton, Sebastopol, CA

>Useful information. It's a pretty saw, under the rust.

Not having previously owned any saws with split nuts, I haven't followed the prior threads on this subject very closely, but my impression is that they're hard to remove without damage. Am I correct that, if I can clean up the saw without removing the handle, I should?

Not going to happen any time soon, in any case - it's likely to be deep winter before I get any significant shop time, and The Shop List is pretty long (though The House List, which keeps growing, has it beat). I sprayed some WD-40 on it yesterday to keep the rust from getting worse while it waits.

Re: First backsaw with split nuts!

#9

Re: Thanks, Ray *LINK*

Ray Gardiner

>Hi Bill,

In this case I would remove the handle and completely dissassemble to clean up the rust. There are any number of good howto's for saw restoration. Bob Smalser come to mind. (see link)

You might need to make a split nut driver if you don't have one.

Mark the position of each of the nuts so that it goes back the same

way, sometimes they are slightly different.

You will be amazed how good it looks when restored.

Regards

Ray


http://www.wkfinetools.com/contrib/bSmalser/z_art/nlOldSaw/nlOldSaw1.asp

Re: First backsaw with split nuts!

#11

Re: First backsaw with split nuts!

steve mackay

>Looks like a lot of patient work ahead. But, in my book at least, well worth the effort ! When its purty it'll be a real pleasure to use. A LOT of folks would'nt bother but that one would get under my skin. AND you'll have a great story behind it.

Re: First backsaw with split nuts!

#12

Hey Bill, That's a fine door stop. :>)

Parisian, VL

>

Re: First backsaw with split nuts!

#13

split nuts question

Bill Tindall, E.TN

>On the chance that I am not the only person not understanding the significance of split nuts, what is it? Does it indicate a maker, or a vintage, or quality or what?

Re: First backsaw with split nuts!

#14

Re: split nuts question

Bill Houghton, Sebastopol, CA

>My information on it is limited to what I've read here - my impression is that it indicates age (and maybe English origins?).

I know none of my various Disston saws, some dating back, I think, to circa 1900, have split nuts.

One side note: the handle on this pile of rust I purchased is counterbored so that the medallion and saw nuts are flush with the handle. It gives a very different look to the handle.

Re: First backsaw with split nuts!

#15

That's my kinda hand saw!

Alan DuBoff

>Bill,

London Pattern is one of my favorites, I have a Beardshaw a tad smaller, I'll have to see if I have a pic, I can't find one at the moment.

Great find, you will be surprised how well that might clean up! :-)

That's the golden era of handsaws, at a time before automation and machines started to take over...

Re: First backsaw with split nuts!

#16

Re: split nuts question

Todd Hughes

>Split nuts are saw nuts where the screw part comes through the nut so you have to use a special screwdriver blade with a slot in the center to take them off.These were used befor later improved saw nuts were devoloped around the 1880s or so. Some cheap saws [and English ones] continued using the split nuts I believe into the 1900s. Not an English thing and older American saws including Disstons will have split nuts as well.

Split nuts while cool, I guess, are a pain to remove and tighten,probably not as strong either.Most were finished , ground flush, after being on the handle so hard to get them back on and have them look right even if you got them off with out messing them up ....Todd

Re: First backsaw with split nuts!

#17

Re: That's my kinda hand saw!

Bill Houghton, Sebastopol, CA

>I'm just real sorry that it got turned into a yard tool. I do hope it cleans up.

Thinking about stopping by that estate sale site again, see if the family's there, get their address in case I can send pics of it refurbished - some day...

Re: First backsaw with split nuts!

#18

Where was that page . . .

steve mackay

>that someone brought up awahile back on slit nuts ? Kind of a "study" and dating thing. Was it on "The Disston Institute" ? Was interesting and kind of a primer for this novice.

Re: First backsaw with split nuts!

#19

Funny... :>)

Scott Burr in Ben Lomond, CA

>I have a broken No.5 that looks a lot like that one. I use it for a door stop...

Re: First backsaw with split nuts!

#20

Re: That's my kinda hand saw!

Alan DuBoff

>I suspect it will clean up nicely. Most often the steel is pretty dark on those, not sure exactly why...and the teeth are often brittle, so be easy on them.

Great saws, and considering that it probably has close to 150 years on it, it's amazing they even hold together, let alone become a useful tool. :-)