Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Tracing a moulding geometrically (Roubo)

Posts

Re: Tracing a moulding geometrically (Roubo)

#26

Re: Update 2: done with the design

ThomD

>That's the first time I have seen swinging two compass line attributed such complexity. I don't know much of anything about the old forms though I occasionally enjoy reading about them. It's practical to do these things in CAD, then you can add them to design files, manipulate them proportionately, make transfers, make percent changes for plane blades and so forth.

Re: Tracing a moulding geometrically (Roubo)

#27

How is the wood oriented...

Stephen Shepherd in the State of Deseret

>in this molding? I am assuming it is made of more than one piece of wood? Is this a traditional design?

Stephen

Re: Tracing a moulding geometrically (Roubo)

#28

Re: Update 2: done with the design

Wiley Horne-- So. Calif.

>Bjenk,

That is very classic and stately (IMO)! I applaud your approach of following, as though you were a student, the procedures taught in the past to woodworkers in the tradition you've adopted. Learning and practicing the fundamentals is an entirely different procedure from winging it. Beethoven started out learning and playing Bach's scales.

When you're done, and look at those mouldings, they will have a different meaning to you than to the casual observer, and the lesson learned will always be part of the toolbox in your head.

Thanks a lot for sharing the Roubo translation and drawing. Like Bill T., I learned something, and hope you will continue to do more of the same!

Wiley

Re: Tracing a moulding geometrically (Roubo)

#29

Re: Update 2: done with the design

Ace Karner

>After watching Don's DVD several times I marked and struck some molding very similar to that your doing. It was small parts for a keepsake box, I didn't want to start on a large project and burn out.

I drew them on the stock with drafting tools and did the set up with my moving fillister and finished with hollows and rounds. I have never had more fun or more satisfaction since I took up word working.

One thing for sure hour sure want to be careful with grain selection.

Look forward to seeing how your moldings work out.

Re: Tracing a moulding geometrically (Roubo)

#30

Re: Update 2: done with the design

Pam Niedermayer, Austin, TX

>I don't consider freehanding as "winging it," which is much too casual. After all, some people are natural engineers, so that freehanding is as precise as using CAD, just takes less time and allows some minor variation that often, not always, adds interest and beauty.

Pam

Re: Tracing a moulding geometrically (Roubo)

#31

Drawing curves

Warren in Lancaster, PA

>I think compass layout skills are valuable and worth learning. It is also worth learning how to make the curve bolder or flatter with a compass. However, a worker with experience can also usually draw fine ogee curves by hand. And a person used to making moldings with hollows and rounds adjusts the curve by eye for better appearance. This kind of work in real materials develops the eye better than just drawing.

In July I had to make a large molding for a for a house (1752) which had its woodwork sold to a museum in 1926. I had at my disposal an architect's drawing (compass drawn, 1927), a cabinetmaker's drawing done at the museum (freehand, 2008), and numerous pictures. The cabinetmaker's drawing looked better and also matched the pictures better. And when I did the work, I tried to copy the pictures as well as follow drawings and measurements.

Re: Tracing a moulding geometrically (Roubo)

#32

Re: Drawing curves

Pam Niedermayer, Austin, TX

>Sounds like an interesting project. Do you get a lot of architectural work?

Pam

Re: Tracing a moulding geometrically (Roubo)

#33

Re: Drawing curves

Warren in Lancaster, PA

>I do a fair amount of work for churches- tracery and carving etc. I suppose you could call some of it architectural.

Re: Tracing a moulding geometrically (Roubo)

#34

Update 3: Pushing the molding

Bjenk Ellefsen------WebKitFormBoundaryAAk3AAy9AAf+

>As promised, I am updating this post with pictures of the actual work.

I pushed the molding today and I am very pleased with it. It's definitely not perfect, the molding has plane marks (I like that though) but its close enough for me. Hey, this is the first time I do a molding with my old tools.

I am very happy with it even though it will never go down as a masterpiece. For me, this is an important milestone in my skills and my journey as a beginner 18th c cabinetmaker!

Thank you all for your feedback!

FIrst pic: The layout


img

Re: Tracing a moulding geometrically (Roubo)

#35

Re: Update 3: Sash and fillister

Bjenk Ellefsen------WebKitFormBoundaryAAk3AAy9AAf+

>I removed wood with a sash and fillister Like Don instructed to do it.


img

Re: Tracing a moulding geometrically (Roubo)

#36

Re: Update 3: Hollow & Rounds

Bjenk Ellefsen------WebKitFormBoundaryAAk3AAy9AAf+

>I used my #14 H&Rs to finish the profile.


img

Re: Tracing a moulding geometrically (Roubo)

#37

Re: Update 3: Finished molding and installed

Bjenk Ellefsen------WebKitFormBoundaryAAk3AAy9AAf+

>The molding installed on the cupboard.


img

Re: Tracing a moulding geometrically (Roubo)

#38

Re: Update 3: Finished molding and installed

Wiley Horne-- So. Calif.

>Bjenk,

Wrapping that big complex moulding around two corners is very impressive! Will you show us the full project when you're done with it? I'll bet Don McConnell is plenty pleased to see his great video teaching put into practice like this.

Wiley

Re: Tracing a moulding geometrically (Roubo)

#39

Great job, Bjenk, beautiful.

Pam Niedermayer, Austin, TX

>

Re: Tracing a moulding geometrically (Roubo)

#40

Re: Update 3: Finished molding and installed------

Bjenk Ellefsen------WebKitFormBoundaryAAk3AAy9AAf+

>Thanks Wiley and Pam! Yeah, installing the molding induced a high state of anxiety and I needed two beers to calm down when I was done.

When I put the finished molding in my miter box, I just stood there holding my large tenon saw in the kerf and repeating "Don't f.. this up" as a mantra. The cuts all turned out good and the installation went very well.

I hope Don is proud of his DVD. There is nothing like it out there. I hope he does more of these.

------WebKitFormBoundaryAA96AA2+AAQ3AALp

Re: Tracing a moulding geometrically (Roubo)

#41

Re: How is the wood oriented...

Bjenk Ellefsen------WebKitFormBoundaryAAk3AAy9AAf+

>Stephen,

The molding is built from two pieces. A three and half inches wide piece and a 2 and half piece.

The profile is similar to the one Dunbar did on the same cupboard but he used a full cornice plane. I looked up this type of profile and found one just like it in the book "Furniture Moulding" by E.J. Warne.

The profile I found which was similar was from a tall chest of drawers circa 1675.

Re: Tracing a moulding geometrically (Roubo)

#42

Re: Update 3: Finished molding and installed------

Don McConnell

>Bjenk et al,

I truly appreciate your (and Ace's) very kind words regarding the DVD. My main hope in doing it was to encourage/enable people to experience the freedom of designing and making their own custom mouldings. So I've followed this thread with a good deal of interest and satisfaction. And, as Ace indicated, sticking a moulding of one's own design can be a lot of fun. There is another moulding DVD in the works - a bit more on that later.

Meanwhile, I thought I'd use your project to delve a little further into the general conversation about drawing and sticking mouldings using H&R's, etc.

Out of curiousity, Bjenk, before you provided information about the scale of the larger ogee and the size H&R you ultimately used, I had attempted to scale it out at my end in order to see what challenges you might run into. Apparently I goofed a bit in that effort, but I thought others might be interested in the thought process involved - as I think it speaks to the issue of designing mouldings, swinging arcs, etc.

As I scaled it, the resulting radius of the concave and convex arcs of the ogee appeared to be about 7/8" (app. 2.2 cm). I then assumed that if your H&R's were an even set, that your #12 H&R might have a width/radius of about 3/4" (1.9 cm) while your #14 H&R would have a width/radius of about 1" (2.5 cm).

If that had been the scenario, a couple of strategies to deal with the radius discrepancies come to mind. One would be to scale the overall moulding up or down so that the radius of the arcs of the ogee coincided with your #12 or #14 H&R. Not always possible or desirable. The other would be retain the overall size of the moulding and slightly alter the radius of the arcs to match your planes. That can easily be done by setting one's compass at either the hypothetical 3/4" or 1", swing a couple of short arcs, using the endpoints and midpoint of the sloping line (e, f & i), to locate the new centers, then swing the new arcs between those points.

But, this really only works in one direction. If you go with the larger 1" radius, the resulting arc is less than 60 degrees (7/8" rather than 1"), so one's #14 hollow can't be used to create the convex arc without fouling the concave portion. In other words, at 1" wide, it is wider than the 7/8" chord of the arc. An issue to keep in mind in designing any moulding.

If, on the other hand, you go with the smaller 3/4" radius, the resulting arc is more than 60 degrees, and your H&R planes will be able to negotiate them. The arcs will be a little "quicker" than the originals, but that will be barely, if at all, perceptible in the final result. I've included a drawing (see below) to illustrate this, with the dotted arcs indicating the originals and the solid arcs indicating the 3/4" radius with arrows pointing to the new centers. The #12 H&R's will simply have to be axially rotated a bit to complete the full width of the arc.

I've gone into this in some detail because I think it illustrates, at the very least, that it is a good idea to keep in mind the width/radius of your H&R's as you design a moulding. If there is no correspondence between your drawing and your planes, the best you can hope for is to painstakingingly creep up on your design with an ill-sized/profiled plane. At the worst, you simply will not be able to get any of your "approximately right" planes into the intended space to carry out the work.

I was quite interested in Bjenk's translation of Roubo, where he indicates that one could free-hand mouldings, but it really is better to design them geometrically (swinging arcs). In part, my interest arises from having read the following text from Peter Nicholson's _Practical Carpentry, Joinery, and Cabinet-Making_:

"But architects, most esteemed for their good taste, never draw the forms of mouldings by these mechanical methods; they always make them of the most beautiful figures they can by the hand; and, like the ancient Greek architects, they avoid circles for mouldings, in consequence of their want of variety, both of outline and of light and shade. Hence, though we give the usual mechanical methods, they are not here recommended to be used in practice."

Well, I guess this is Nicholson paying lip-service to the supposed hierarchy of the fine vs. decorative arts. But it is a complete and utter pose. As he indicates in the text, itself, his own illustrations of various mouldings are all done geometrically. And I don't believe this is only for the sake of convenience, as he seems to imply. He knew, as do we (and Roubo), that the profiles of the soles/irons of the H&R's that the workmen would be using to stick any of these mouldings are all portions of arcs. Quite simply, the most efficient and direct way to design and stick these mouldings with H&R's is to base them on true arcs.

Yes, there is the question of Greek mouldings, as Bill H. brought up earlier, which appear to have been based on sections of ellipses. If one insists on mouldings to be truly elliptically based, then, probably, the best bet would be to use a dedicated/complex moulding plane of the correct profile and size. Or, possibly, to approximate the shape with H&R's, then finish up with an appropriately shaped scratch stock or sanding block. Not as direct or efficient, though.

On the other hand, approximations in the form of ovoid figures can be done fairly directly using H&R's. In other words, a four-center ovoid form (i.e. a curved form consisting of combined longer/slower arcs and shorter/quicker arcs) can be used, and the ovoid moulding executed with two different sized hollows or rounds. Takes a bit of layout skill, but it can be done.

Another thing often done is to design ogees or cove/ovolos using only 60 degree arcs, such as Bjenk has done. Since these aren't "square" in feel, they can seem to simulate elliptical curves. In fact, I've seen examples of such mouldings completely misidentified by writers as being elliptically based.

In my upcoming DVD, focusing on complex sprung cornice mouldings, I follow a method which I believe to be period based. My reason for mentioning it, here, is that the only way that method will work is to have the entire moulding completely and accurately designed before any tool touches the wood. And the curves of that moulding, based on a period drawing, are all true arcs (including one ovoid curve). I had a blast doing that shoot.

Don McConnell

Eureka Springs, AR


img

Re: Tracing a moulding geometrically (Roubo)

#43

Very nice! Pin nailed?

Scott Burr in Ben Lomond, CA

>Just curious...

Re: Tracing a moulding geometrically (Roubo)

#44

Re: Update 3: Finished molding and installed------

Bjenk Ellefsen------WebKitFormBoundaryAAk3AAy9AAf+

>Don,

What a great post this was. I have also read Nicholson and that is something that caught my attention as well. I made sure to design the profile geometrically to stay close to my H&Rs. Like you said in your DVD, H&Rs are not made in standardized way. I used my #14s and while the convex portion worked well, the concave dug a little in the top of the concave. I will have to measure carefully my H&Rs.

I did design the profile using 60 degree arcs to overcome the fact that my ogee is not square. Ellipses can also be traced geometrically if that's what we want to do. Just like you said, my cyma may appear to be based on ellipses but its definitely based on arcs from a geometrical circle. It made things easier as H&R are quarters of circle or at least they are close enough.

I can't wait to watch your new DVD and if you don't mind, I would like that we continue this discussion based on your upcoming approach.

Don, please continue your work. You made this possible for me!