Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

289 users -- ever wish 4 a left-handed version?

Posts

Re: 289 users -- ever wish 4 a left-handed version?

#26

Re: actually, it's not much of a problem--never wa

Jim O'Neal

>"I've gotten quite fond of straight rabbets, so much so I can't imagine obtaining a skewed one until I had a full range of sizes of straight rabbets."

Larry, what would you recommend as "a full range of sizes" of straight rabets? I'm gradually buying various wooden planes in order to begin making my own simple moldings and I'd like to keep the various planes of the same type to a minimum, if I can. I was thinking about purchasing one of your moving fillitsters, but maybe I'd be better off to buy a few rabets, instead.

What do you recommend?

Re: 289 users -- ever wish 4 a left-handed version?

#27

Re: actually, it's not much of a problem--never wa

Wiley Horne--So. Calif

>Larry,

Want to make sure I understand the implications of what you just said. For me, the moving filletster is good for immediately establishing the rebate, though as you say, the final cuts will be made with a rebate plane (for me, a shoulder plane) both to square the cut and put a fine finish on it.

Two questions: First, is the difference between the cabinetmaker and the joiner--in your quote--that the cabinetmaker requires a plane that will work the rebate in either direction, so as to ease the problem of tearout in reversing grain?

Second, if you don't use a moving filletster, how do you proceed? Do you strike a gauge line, then deepen it with the snipe bill, then move to the rebate? I recall you describing how Don and yourself came across this procedure in one of the old design directors (Chippendale maybe?).

Thanks in advance for your insights!

Wiley

Re: 289 users -- ever wish 4 a left-handed version?

#28

Re: actually, it's not much of a problem--never wa

Pam Niedermayer, Austin, TX

>Do you mean rebate as in LN 10-1/4 carriage or a simpler rebate-on-one-side?

Pam

Re: 289 users -- ever wish 4 a left-handed version?

#29

Re: Larry, how about a moving fillister

Larry Williams

>It'll work fine. It's just slow and tedious to get one set dead accurate. Working to gauge lines is accurate, simple and direct but roughing with a moving fillister isn't a bad way to go.

Re: 289 users -- ever wish 4 a left-handed version?

#30

Re: actually, it's not much of a problem--never wa

Larry Williams

>Hmmm, I think I'd want to start out with 5/8", 7/8" and maybe 1 1/4" straight rabbets at 50�. Don tells me it'd be best if I called them square rabbets like the early literature. I'm sure he's right, he almost always is.

Re: 289 users -- ever wish 4 a left-handed version?

#31

Re: actually, it's not much of a problem--never wa

Larry Williams

>Wiley,

I think what Denning was saying is that the joiner uses mostly pine (deal) and the cabinet maker uses mostly hard woods. I think, though, the important part of his quote is "...a fact which the trained cabinet-maker is aware of..." If one is working to gauge lines, the time to set up and tinker with the moving fillister isn't necessary. I guess what you would use to start the rabbet would depend on the situation. You could use the snipes bills to start out of your gauge lines but even that takes a little time. For a rabbet like you'd create with a moving fillister starting with just a straight (square) rabbet is simple, quick and direct. Just use your fingers as the initial fence, you won't need that for more than a couple passes. Not having to fight the drifting nature of the skew rabbet really makes the process easy.

Re: 289 users -- ever wish 4 a left-handed version?

#32

Re: actually, it's not much of a problem--never wa

Larry Williams

>Neither one of those Pam. I'm talking about just the common conical escapement wooden rabbet plane.

Re: 289 users -- ever wish 4 a left-handed version?

#33

Loctite

Bill Houghton, Sebastopol, CA

>the bearing fixing type is pretty impressive, if the tolerances are right - you need 600 degree Fahrenheit to remove it. Melt the paint.