Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Nicholson-Cherubini workbench *Update*

Posts

Nicholson-Cherubini workbench *Update*

#1

Nicholson-Cherubini workbench *Update*

Bjenk Ellefsen

>I finally completed most of it. I successfully jointed the top with a 22 inches wooden try plane.

Tenons and mortises were easy enough as I am getting quite good with them. My sawing has tremendously improved, I think. I have gotten pretty comfortable with following two lines and I am now at a point where I am cutting to the lines on the first try. Practice makes perfect!

I think I broke my brace. Luckily, its not 200 years old like most of my other tools.

What went wrong was the bed bolts. I have no idea why but I just couldn't align the nuts holes with the bolts. I gave these up and I am stiffening the rest with upper stretchers. The bench is designed by Adam to be knocked down and I have tested the operation. It is quick as it takes about ten minutes to assemble/disassemble.

I still need to pierce holes for the holdfasts, install a front vise and make the planing stop. Oh, and flatten the top.

:)


img

Re: Nicholson-Cherubini workbench *Update*

#2

Re: bed bolts

Adam Cherubini

>I think bed bolts are designed to work in conjunction with tenons. In this case, the fit of the hole is irrelevant. I make tight fitting tenons and loose holes for the bed bolts. Some guys use the bolts to transmit shear. While this is easier than making a M&T joint, it requires precision holes. I have nothing against this approach. But in this case, I think the traditional way is easier and stiffer.

One problem you may encounter is that the flange at the head is not as large as you would want. And the counter bore for the head is so deep that the material left under the head to the bottom of the mortise is small. Bore too big a hole and you could get pull through. What I did was drill a pretty tight hole in the leg, and then larger hole in the stretcher.

Just be happy this isn't a bed and you have 2 bolts perpendicular through this joint!

Adam

Re: Nicholson-Cherubini workbench *Update*

#3

Re: Nicholson-Cherubini workbench *Update*

Pam Niedermayer, Austin, TX

>Looks really nice, Bjenk, good work, love it that it's a knock down. Let us know how it works.

Pam

Re: Nicholson-Cherubini workbench *Update*

#4

Re: Epoxy Bonding

ThomD

>My prefered way to mount bolts for maximum performance with minimal effort is epoxy bonding. This is the way used in high performance structures, and while it isn't traditional it works better and leaves fewer scars.

The way it works is an oversized hole is drilled in the endgrain with a spade bit, 3/4" is ok for 1/2" bolt in this kind of application, 4" deep shoul'd be enough. this hole can be freehanded and the precise position and straightness isn't hyper important. Then the compressed member,or a jig block is drilled with a 13mm bit to allow the bolt to be inserted with a layer of tape. The bolt receiving member is raised to a vertical position, and the compressed member is placed over it with the bolt in postion. The receiving hole is filled with epoxy that will suround the bolt when the parts are brought together. After the glue dries the parts are separated, barrier tape removed and one has a perfectly mounted stud ready to be attached through the compresion member.

Re: Nicholson-Cherubini workbench *Update*

#5

Re: bed bolts

Bjenk Ellefsen

>The funny thing is that I did try to bore a bigger hole inside the stretchers, a one inch hole this time, but still missed the bolt by a little. The bolts are a little off because the small holes through the legs and through the tenons are off. I guess I was going at it with the brace too hard. Douglas Fir is stiff and it was hard work. I suck!

That will teach me! At least the tenons are so big that they hold the legs very well.

Re: Nicholson-Cherubini workbench *Update*

#6

Jim in Burlington Ont.

Nice One

Jim in Burlington On

>Like that style and look quite a bit. Seems it could be simplier and cheaper to build than most of the heavy topped models.

Re: Nicholson-Cherubini workbench *Update*

#7

Looking good.

Parisian, VL

>

Re: Nicholson-Cherubini workbench *Update*

#8

Re: Nice One

Bjenk Ellefsen

>Its the cheapest bench I know! 40$ for the legs and stretchers in Douglas Fir and 50$ for 4 2X12 construction lumber. However, the wooden screws for the vise is what is making this expensive. I bought them. I guess someone looking for a less authentic look and function could get two tail vises from Lee Valley for a fraction of what the wooden screws cost.

Also one of the quickest bench to build. This thing is about three times cheaper than the "European" bench you see in the back but is about three times more useful to me as of now.

Re: Nicholson-Cherubini workbench *Update*

#9

Rock On Bjenk!

Scott Burr in Ben Lomond, CA

>Well done! It's looking real good.