Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

OT - Auto Radiator repair

Posts

OT - Auto Radiator repair

#1

OT - Auto Radiator repair

David Miller from Iowa

>Sorry to go off topic, but the board is kind of slow these days and you are my go to guys...

Bought a new radiator for the 1989 GMC Sierra truck - discount radiators.com. So far pretty good - the thing showed up in th mail in two days and seems like the right one. Except it has a couple extra threaded holes in it - sort of like they made it to fit several different vehicles and you could choose some holes and plug others.

Except the holes have some funky thread - size is close to a 1/2" pipe plug, but a finer thread. Any ideas on what I can use to plug these?

Thanks

Re: OT - Auto Radiator repair

#2

Re: OT - Auto Radiator repair

Mike Jurnigan in Suffolk

>It sounds like they are for transmission cooling lines. If memory serves me correctly they are an inverted flare fittings. If you vehicle has a manual transmission you can just plug them. NAPA sould carry the fittings.

Mike in Suffolk, VA

Re: OT - Auto Radiator repair

#3

Re: OT - Auto Radiator repair

Joe Rogers, Northern Virginia

>True and they may be oil cooler fittings also.(trans fluid cooler is the same basically just different fitting sizes) If they had little plastic or rubber protector plugs installed in them when shipped they should suffice to keep debris out. They don't need to be sealed.

JR

Re: OT - Auto Radiator repair

#4

Re: OT - Auto Radiator repair

goodolboy

>Most threaded holes into an automotive type radiator should have brass plugs/fittings available to fit and seal them. (You MAY get lucky and just be able to use an extra radiator drain plug temporarily if it's the right size, but a permanent fix for any extra holes is usually a much better idea.)

The first step is to be sure of what the extra hole(s) drains, is it water or transmission fluid that would come out of those holes? If it drains water you'll need a more secure (higher pressure) fix than if it's transmission fluid (lower pressure). Best is to use a brass to brass connection when possible (if it's a brass tanked radiator), because you'll be able to get it apart later if you ever have to, and using similar metals that expand and contract more uniformly in response to heat and cold makes leaks less likely down the road.

Sealer or Teflon tape might be necessary on the threads, if it's not a tapered thread, but go slowly when tightening things and don't use any more pressure than necessary to make sure it doesn't leak, it's VERY EASY to crack loose a soldered-on or screwed-in radiator fitting by over tightening it.

Older type hardware store are a good place to look for smaller brass fittings if you can't find them at a NAPA type automotive store that has a large selection of fittings.

Home center type store are sometimes WORSE than a waste of time because in this case you really need to know what STYLE of thread is involved and a lot of minimum wage people working there won't know or even be able to SEE the difference between the right one and the wrong one, and you could possibly end up with stripped threads. Take the radiator with you to be sure of a snug and proper fit. With new fittings, they should snugly engage at least a few threads with finger pressure alone if it's the right fit.

Re: OT - Auto Radiator repair

#5

Re: OT - Auto Radiator repair

goodolboy

>And obviously, if your truck isn't an automatic transmission model, and it IS a transmission cooler connection, you won't have to worry about it as much, although occasionally a water leak is traced back to one of those soldered-on-the-inside radiator transmission coolers.

Re: OT - Auto Radiator repair

#6

THANKS - Projected Successfully Completed

David Miller from Iowa

>

Re: OT - Auto Radiator repair

#7

Re: THANKS - Projected Successfully Completed

Parisian, VL

>Great to hear. Glad someone on this board is doing something productive.

Victor - in Hot and Humid Houston