Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Metal head stuff

Posts

Metal head stuff

#1

Metal head stuff

Wiley Horne -- So. Calif.

>Hi All,

I'm persevering with a metallurgical project to examine polished and etched blades at high magnification.

As one detail of this, I need to glue two pieces of steel together, using an adhesive that (a) will hold tight, but (b) can be gotten apart again without using high heat (as in detempering high), and without yanking chunks of steel off the glued members. Maybe something that hot water can get apart. I guess I need the steel equivalent of hide glue. Is there such an adhesive?

Wiley

Re: Metal head stuff

#2

Re: Wood head stuff

Stephen Shepherd in the State of Deseret

>Wiley,

Just etch the steel with a clove of garlic then glue it together with hide glue. Warm to 144.5 degrees and the glue releases.

Stephen

Re: Metal head stuff

#3

Re: Wood head stuff

Wiley Horne -- So. Calif.

>Stephen,

Wish I had a garlic clove around my neck, like kids used to have to wear (and maybe still do some places). If so, I'd go try that right now. However, it'll have to wait til I get to the grocery store again.

You're not sending me on a snipe hunt, are you?

Wiley

Re: Metal head stuff

#4

Rubber cement? Weatherstripping adhesive?

Bill Houghton, Sebastopol, CA

>I'd experiment with rubber cement from your local office supply store (Barge, available in better hardware stores, some shoe stores, and leather stores, is, I believe, also a rubber cement). If that doesn't work, automotive weatherstripping adhesive sticks to metal, along with your fingers, your clothes, and adjacent surfaces. Both can be peeled apart, and cleaned off - can't recall the solvent, but the labels should say.

Maybe not as romantic as garlic-flavored horse hooves, but at the current cost of food, it's a shame to waste good garlic.

Re: Metal head stuff

#5

Re: Wood head stuff

Stephen Shepherd in the State of Deseret

>Wiley,

Not a snipe hunt, but a real way to clean metal prior to gluing with hide glue. Actually liquid hide glue will hold metal and other non porous materials to wood or other materials better than Hot Hide Glue.

And the garlic etches the metal giving a better key for the liquid hide glue to adhere. (It will be in the book, as well as other uses of garlic).

Stephen

Re: Metal head stuff

#6

anything

Bill Tindall, E.TN

>All adhesives will soften and yield well before tempering temperature. I would use cyanoacrylate for the task. Depending on the strength required, hot melt craft adhesive could work.

Re: Metal head stuff

#7

Re: Metal head stuff

Derek Cohen (in Perth, Australia)

>Hi Wiley

Use a thin layer of 5 minute two-pack epoxy (this should be freely available in tubes in most hardware stores). This will soften under heat - hot air gun or hairdryer.

Regards from Perth

Derek

Re: Metal head stuff

#8

From The Tool & Die Maker . . .

steve mackay

>My Dad, that is. Passed your question on to him. For metal Hes the master.

Krazy glue is a good option to try since we know if we glue our fingers

together with Krazy glue or Super glue you have to soak them with finger

nail polish remover to soften the glue to get fingers apart.

You might try this method for your project.

Re: Metal head stuff

#9

Re: Metal head stuff *LINK*

Marv....... Northern California Lake Co.

>Hi Wiley,

Understanding your requirement, I would suggest you use a type of adhesive that is used to glue fabric. It should adhere just enough to do what you need to do and then be easily taken apart. You can buy it in tube form that makes it easy to apply without a lot of messing around. These adhesives are flexible which means they do not set up hard.

Below is a link to a website where you can read about the different kinds of these adhesives.

Marv


Adhesives

Re: Metal head stuff

#10

Re: Metal head stuff

Tony Zaffuto

>You may want to try Gorilla glue. It's advertised as used for bonding items to steel, etc., so it ought to work steel against steel. If someone has already posted this suggestion, I apologize for this message!

T.Z.

Re: Metal head stuff

#11

Thanks very much everyone!!

Wiley Horne -- So. Calif.

>Turns out that superglue/crazy glue/CA is probably best in this application, as it will tend to form a hard shell and reject debris (at a micro scale) which will want to get into the seam between the metal parts being glued. At least, that's the best guess.

Still gonna get some garlic to try out my nice fresh Old Brown Glue (per Stephen's recommendation). That'll make the best story for later, if it works. Incidentally, when I ordered the Old Brown Glue, the lady who answered the phone and took my order for Patrick Edwards down in San Diego was most cheery and delightful.

Thanks again everyone!

Wiley

Re: Metal head stuff

#12

Re: Metal head stuff

Robin Corell in Atascadero CA

>I suspect that the CA glue will work nicely for you and it cures quickly. Another option in addition to the hide glue is shellac. before the invention of contact cement it was used to glue rubber tires onto bandsaw wheels. the downside to shellac as an adhessive is that it often takes 24 hours to cure.

Robin