Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

My bech continued...

Posts

My bech continued...

#1

Corey Megal

My bech continued...

Corey Megal

>Here are a few more pictures for those that asked for them. I tried to show the details of the work holding a bit more. You can see the tail vice and how I had to offset the dog to line up with the dog holes in the bench. When I drilled the dog holes (before the final glue up) I drilled them from the bottom with a 1" bit to a depth of about 2", then drilled the 3/4" dog holes from the top. The reason I did this was that I had read the holdfasts may not hold as well in a full 4" thick top. Also, I use the Lee Valley bench dogs and they are a little short for a 4" top, the extra clearance at the bottom helps me push them up. I've thought about lengthening them with a bolt, but so far it hasn't bothered me enough.

Thanks for the kind words.

Corey


img

Re: My bech continued...

#2

Corey Megal

Re: My bench continued... 

Corey Megal

>


img

Re: My bech continued...

#3

Corey Megal

Re: My bech continued... 

Corey Megal

>


img

Re: My bech continued...

#4

Corey Megal

Re: My bech continued... 

Corey Megal

>


img

Re: My bech continued...

#5

Corey Megal

Re: My bech continued... 

Corey Megal

>


img

Re: My bech continued...

#6

Nice bench Corey! Are those

Stuart Hough

>3/4" boards laminated together? I was wondering if that would take longer to build that way, and if it feels nore solid than using 2" wide pieces. I really like the look of the smaller boards better than the wider stuff. Thanx for the pics!

Re: My bech continued...

#7

Re: My bech continued...

charlie belden

>I've got to ask

Why chose the leg vise and jamb stop when there are so many other choices available today?

The leg vise is a 17th/18th Century answer to how to hold wood, given that iron vise screws were either not available or prohibitively expensive and the jamb stop predates the leg vise. Since the moveable vise jaw doesn't close parallel to the fixed jaw (the face of the bench) it requires a spacer block for each board thickness in order to close parallel or if not the jaw closes at various angles to the fixed jaw unless it's completely closed?

Is there some unique capability the leg vise provides and if so what is it? I can understand the throw back shoulder vise because it lets you clamp longer parts vertically for doing things like cutting dovetails and other end grain joinery - with no vise screw in the way. But the leg vise has the vice screw in the way.

And because the moveable jaw on a shoulder vise is on a swivel, it will angle to match non- rectangular parts. But the leg vise?

And with modern "quick release" vise hardware, which are quick and easy to move to match the stock, I find turning my shoulder vise screw three or more turns to fit a thicker piece of stock a minor waste of time and a bit irritating. The benefit however outweighs that.

So what special capabilities does a leg vise provide that more modern vise hardware doesn't?

Re: My bech continued...

#8

Corey Megal

The leg vice

Corey Megal

>Well, there certainly are no great advantages to the leg vice, everything you say is true. I realize I could stop there, but here you go:

It has a ridiculous amount of holding power. It was cheap, I built this bench for $550, including the glue. I liked the look of the bench with the leg vice. I like to build a lot of different projects, and this vice seems to adapt well to a lot of situations. I could dovetail any width piece, one side clamped in the leg vice, the other clamped to the front of the bench with a clamp. I haven't used the bench a ton yet, I may grow to dislike the vice, and if I do, I'll replace it with something else. I guess I want to give it a chance first and see.

Re: My bech continued...

#9

Corey Megal

Re: Nice bench Corey! Are those

Corey Megal

>Yep, 3/4" or slightly greater, I stopped running them through the planer as soon as both faces were clean. I used plastic resin glue, and it worked well, longer open time, and less creep than yellow glue. I glued it up in five subsections, then glued those together. I was able to buy 200 BF of 4/4 maple, so that's what I used for the bench. If I could have used thicker stuff, I would have. I used a LOT of glue. I am happy with the way it turned out, though.

thanks,

Corey

Re: My bech continued...

#10

Jack Guzman from Maine

Re: My bech continued...

Jack Guzman from Maine

>Charlie,I hope I'm not being rude intruding into Corey's post but I had to answer your question about leg vises. I find it to be superior to modern metal vises in alot of ways. Like Corey said,the holding power is good.Also due to it's design,you get a greater depth from the top of the jaws to the screw. With my metal face vise with wooden jaws I find that even with a taper built in,the top of the jaw tends to spread apart(tip outward)under pressure.The leg vise,on the other hand doesn't have this problem.The parallelism of the jaw is adjustable with a sliding bar or screw at a lower pivot point in most designs of these.I'm not sure about Corey's design,I couldn't tell from the pictures but all the ones I've seen have this feature. All vises have downsides and I guess it depends on your own personal woodworking needs,but I personall;y find a leg vise to be very handy.---Jack

Re: My bech continued...

#11

LOL.... $550, including the glue 8^)

Scott Burr in Ben Lomond, CA

>

Re: My bech continued...

#12

Thanks Corey! Nice to see it in action...

Scott Burr in Ben Lomond, CA

>Thanks for the pic of the bench stop in action. Nice to see it up close and personal. I see you placed a few planes for effect! If that's a bronze LN no. 4 you suck!

Thanks again for the extra pics.