Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Any Idea What This Is?

Posts

Any Idea What This Is?

#1

Any Idea What This Is?

David

>A few years back I found this "thing" in the wall of my house while doing some repairs. The house is post and beam and was built in 1821. Way up top on a knee brace between a second floor corner post and the beam that supports the roof rafters was what I have come to call bagel tongs of the late republic.

A few folks including an archaeologist have looked at this and no one has a clue. I thought it might be some sort of apprentice's project. Figured I'd try with you guys who seem to have seen it all.

Thanks!


img

Re: Any Idea What This Is?

#2

tuning fork for wooden planes

McKay

>

Re: Any Idea What This Is?

#3

Dale Lenz

Re: At first.....

Dale Lenz

>thought it was a stress test sample, caseharding, But sawn wrong way. How about chopstick trainers, : ' >.

Re: Any Idea What This Is?

#4

Re: Any Idea What This Is?

Victor Parisian

>I'm guessing some sort of guage for marking hole locations.

Or how about a tool for pulling rope or twine through a wall openning?

If this was something that had to be repeated over and over like tying thatch, the slot would sure make it easier than untying a knot each time it was passed through.

Just Guesses

Victor in Houston where we are having Chamber of Commerce Weather this week.

Re: Any Idea What This Is?

#5

Re: The real answer

ThomD

>I ave have made things just like that, and what they were for was to transfer blind measurements. I used mine mostly for boatbuilding. But a house example that I am just making up, but it will give the idea would be imagine putting something in the way of clading on the structure. I will use drywall if not historically accurate. You put the boat over everything including window openings. Today you would establish the opening by using a trim cutter or router with a cartridge bearing that would run on the window framing. But another way is to rough out the opening within a few inches all around then take the tuning fork so one leg rubs the framing and the other allows you to draw a line. This will allow you to precisely outline the frame from the back side to the front and then cut it in with a saw.

The kind of thing in boatbuilding is if I put down a 1/8" plywood deck, then trim it to within 3 inches, then I would run my line showing exactly where the side of the shear is, but on top of the plywood, then I could vac bag down some balsa core to that line without wasting materials. I need the run-wild to have a place to glue down the vac bag. later I can trim it either to the scribebd line, or to just blow it out with a router. In that case the main advantage is economy, knowing where to stop using an expensive material.

However given how precise that thing is it would be for doing open skirtboards (OSs) onstaircases. Today the way we do it is build a 2x staircasse. Then come to the outside of the staircase and run an OS board accross all the open ends and as low as required to give the trim we want. Then we take that gage and fit it over the OS level with the tread allowing us to transfer each tread to the outside surface of the OS. We do the same with the kickboards, which may be vertical or sloped. That line also transfers to the outside, however it needs to be advanced by the thickness of the OS, which ought to be the width of the arm on the gage. Then we un-tack the OS, and saw the tread lines at 90 flush, and the kick lines with miters. Then we refit the OS, and permanently attach, then your decorative kicks are flipped over so that the newly formed 45s allow scribbing the outside of the miter on the kick and the inside is scribbed or butts at 90 on the skirt at the wall thereby allowing perfect fits without any math whatsoever.

Re: Any Idea What This Is?

#6

Re: Any Idea What This Is?

David

>I've joked that it is a wooden tuning fork because it does indeed make a nice low hum when struck. Never made the wooden plane connection :)

Also thought that it might have been something that an apprentice would make for practice but just a guess.

Re: Any Idea What This Is?

#7

Re: Any Idea What This Is?

richard jones

>We called them "preachers", since they weren't supposed to lie........

Gauge for marking something, I think, the hole was drilled so the waste didn't have to be chiseled out.

Rich

Re: Any Idea What This Is?

#8

Good one !

steve mackay

>

Re: Any Idea What This Is?

#9

Re: Any Idea What This Is?

David

>A gauge of some sort makes sense. Now if I could only figure out for what. The slot is 12 3/8" x 1/2 which doesn't line up with anything that comes immediately to mind. I wonder, however, if it could have been for installing the accordion lathe?

Re: Any Idea What This Is?

#10

Re: Any Idea What This Is?

ThomD

>That's the kind of thing. though I would imagine that might be the right size for treads, by the time one ensured they would not hit anything for sure. Part of the building it was found in, was it near any stairs, of course one can get too rational. Amagine people trying to piece together fastener distribution from a nailgun fight.

Re: Any Idea What This Is?

#11

Re: Any Idea What This Is?

Philly

>David

When making wooden planes you check the progress of the bed by sliding this jig into the mortise - you then can visually see how close you are to your layout line on the outside of the plane.

Hope this helps

Philly

www.phillyplanes.co.uk

Re: Any Idea What This Is?

#12

Re: Any Idea What This Is?

richard jones

>Both of those dimensions would probably be a bit more than was necessary to straddle whatever, maybe a lot more. Moulding or siding comes to mind when I see something like that. Fitting some wide moulding to some oddball shape, like around a stone fireplace?

Good mystery. One good thing is that the tool that you found is handmade and in just as good working condition as when it was made........

Rich

Re: Any Idea What This Is?

#13

Re: Any Idea What This Is?

Stephen Shepherd in the State of Deseret

>At first I thought just what Philly did that it was for checking the angle of the bed in planemaking.

However it might be a gauge for testing the thickness of large tenons.

Stephen

Re: Any Idea What This Is?

#14

Re: Any Idea What This Is?

David

>The "gauge" was found on a knee brace highest outside corner of the house. No stairs within 20+ feet. Original siding was cedar clap, ~5" exposure. The nearest trim boards are too wide (~17") and thick (1"+) to fit. The tenons on the frame are well over 1" thick.

I hate to sound like I'm shooting down everyone's ideas, not my intension. Frankly you guys are great at figuring this out. I kind of like the plane gauge idea.

DGW

Re: Any Idea What This Is?

#15

Something to think about

Dan Donaldson

>Whatever it is, I have to wonder if the person that made it ever considered that sometime in the future, it would be found and generate a thread like this. Whoever made it used it for its intended purpose and then basically threw it away. I wonder if sometime in the future from us, someone will find some item that one of us made quickly for some purpose, and then tossed away for someone to find and wonder. I was recently in Phoenix and we went to the Heard (sp?) Museum that has a lot of Native American artifacts. I was thinking about that same thing as I looked at some of the work on display. Wondering about the craftsman that made it and what he/she would think if they had any idea where the item would eventually end up.

Guess my mind must work funny ;-)

Re: Any Idea What This Is?

#16

Humidity Gauge

Garrett in Victoria

>No kidding. The tines of the fork move together in humid weather and apart when it's dry.

Cheers, Garrett

Re: Any Idea What This Is?

#17

Tongs

Jim Reed @ Tallahassee

>One of my jobs as a kid was to develop x-ray film at my dad's vet clinic. We had some wooden tongs that looked just like what you have. Your tongs would work well for picking things, like cloth, out of a lye bath. Perhaps used to dye cloth. Your tongs look unused. The wood, of course, would be non reactive in most cases. Just a guess.