Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Tap and Die

Posts

Tap and Die

#1

Tap and Die

Ralph Ambrosio

>I have built a few small wooden boats using Tom Hill's method. I have always used trial and error method of shaving the bevel on the ends of the planks with some success. What has stopped me from getting the most out of Hill's system is my reluctance to drill, tap and die my low angle block plane and attach a 6" hardwood 3/4 by 3/4 "arm." The "arm" rides along the ribbans and replicates the bevel on the edges of the planks.

I have never done this...is this a job for a machine shop or is this something a moderately skilled woodworker could do. Thanks.

BTW, the low angle block plane is a recently purchased new adjustable throat Stanley.

Re: Tap and Die

#2

Well, I'm not a metallurgist, but...

Alan DuBoff

>Cast iron is not difficult to drill at all, it is quite easy.

I'm not clear on where you're drilling, but most planes are cast iron and should be fairly soft as such. You could probably do it with an old egg beater by hand even.:-)

Re: Tap and Die

#3

easy

Bill Tindall, E.TN

>Cast iron is the easiest of any metal to drill and tap and you won't die.

I would recommend a drill press for drilling. Cast iron is self lubricating so no need for cutting oil. The right sized drill will be stamped on the tap. When tapping twist it in and if it has a step change in increased resistance turn it backward 1/2 turn to clear the chips. So the routine is approximately: 1 turn forward, 1/2 turn back, and repeat.

Taps are frail affairs and it is not a pleasant day to break one off in the hole, so don't force. When going in (clockwise) if it hangs it is probably because chips have jammed and the reverse turn clears them.

Re: Tap and Die

#4

I learned at about 12 or 13 . . .

steve mackay

>from the best Tool & Die maker in the whole wide world ( Dad ). Its no sweat. Just a bit of confidence. THe most ticklish part is makeing DARN sure you punch your starter marks EXACTLY where you want 'em. Measure this one FIVE times and drill once ! And keep everything straight. Good luck ! Strike that . . . no luck involved. Just attention to detail.

Re: Tap and Die

#5

Re: Tap and Die

Marv....... Northern California Lake Co.

>Hi Ralph,

Use as large a screw as is practical. For what you are doing I would suggest a 10-32 screw thread.

Use a one-handed tap wrench if you have one.

Drill the holes so they go through.

Best to do it on a drill press and clamp it down. Cast iron tends to grab as the drill goes through.

Best to use cutting fluid like what is used for pipe threading. Dark brown stuff.

Drill the tap hole using a drill one size larger than what is normally recommended. For a 10-32 you would use a No.20 drill. No.21 is recommended but thats for a full thread. You don't need a full thread. As a general rule,a little bigger hole allows less chance of breaking your tap.

Use cutting fluid, not because you can't tap cast iron without it but use it because it makes the tap last longer. Cast iron is quite abrasive.

For best results use a sharp tap, not some old worn out dull thing.

Cast iron is the safest metal for a beginner, so don't get anxious about it.

If you can, drill your wood piece first and use it as a template by clamping it to your plane.

After two tapped holes, you'll be an expert.

Marv

Re: Tap and Die

#6

Slight disagreement and clarification *LINK*

Bill Houghton, Sebastopol, CA

>I was taught that, because cast iron has a fairly coarse crystalline structure, you should use coarse threads whenever possible - 10-24 rather than 10-32, for instance (having said that, the generator bracket on my, and now my son's, 1949 Studebaker truck motor is held on with fine thread cap screws because the coarse stripped out in the cast iron block - and it seems to work fine). I think the critical issue is probably how thick the casting is where you're tapping - hold a sample screw up to it, and if you'd have just a thread or so in the casting, go with a finer thread.

I think what Marv means by a "one-handed tap wrench" is linked below. I'm not recommending this particular vendor - it was just the first one that popped up from a Google search. This is by far my preferred type of tap wrench for little taps. Any hardware store will have a selection; be sure the wrench you buy fits the tap you buy, as there are several sizes. The hands-down coolest ones are the ones the machinists use - Starrett and like that - but I got by for years with generic no-namers until inheriting a sweet little Starrett from my uncle, which is practically all I use for the taps that fit it.

I will concur with others that tapping is way less scary in reality than in thinking about it, unless you're tapping with tiny taps (#4, #5). These break if you breathe wrong while using them. Anything from #6 up is strong enough for careful but confident use.

As to the lubrication issue - I tap cast iron dry a lot, wet sometimes; depends on how much of a hassle lubricant will be. When I tapped the block on my Studebaker, mentioned above, I was tapping holes that went right into the block, and didn't want to get cuttings into the oil, so I slathered the tap with grease instead, and backed it out every few turns to wipe off the grease and shavings and put fresh grease on. Worked a treat. What I'm saying is that it's not that big a deal. Don't spend a lot of time looking for "the right" lubricant - motor oil, sewing machine oil, etc, should be fine.


also known as a T-handle tap wrench

Re: Tap and Die

#7

Re: the real answer

ThomD

>That modification always looked like a pretty big hole to me, in the 5/16" range. For that I would want a drill press, and some center drills a few to move up from the initial dimple to the 1/4" final you would need to go 5/16 coarse. You need some serious hold downs.

Hill used a rebate plane for that, I think, partly because in cutting the gains at the stem you need to be able to not only strike the bevel, but work down through the plies so that where the ply attaches to the stem it is flush. Of course you can do a work arounds on that with saws and stuff.

In the book he is pictured with the block plane modified, and I think you could get away with a pretty small hole there as has been suggested or even without taping it at all. Not sure what is shown in the movie.

Three other options from an endless list:

- If your block plane uses a thumb screw, like the LV, build a jig that clamps off that screw and produces the incidence reference you want.

- There are a variety of rebate planes that mount fences that can be easily adapted to this task, they already have a hole and a set-screw, just replace the fence with an incidence one.

- take a few minute and make a wooden one, then mortice the incidence device into the wooden body.

Remember, Hill is a pro who built from a fixed list of boats. If you are making boats of widely different designs, as often amateurs do, the whole jig he makes up takes more time than just shooting the bevel by eye and doing a little fitting.

Re: Tap and Die

#8

Re: Tap and Die

Ralph Ambrosio

>Gentlemen,

Thank you. I will proceed with the Tap and Die drilling first with hold downs on my bench press. As always, top of the line advise.

Ralph