Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Hatchets?

Posts

Hatchets?

#1

Hatchets?

Brad in Ottawa

>Just curious how many people use hatchets in their woodworking?

I just picked one up after realizing on my last project that it would have been really handy to have. Any pointers for uses, usage or sharpening would be appreciated!

Brad

Re: Hatchets?

#2

Re: Hatchets?

Marv

>Hi Brad,

I have a collection of hatchets. I sharpen them on my belt sander as a first step, then I hone them to a fine edge. When I can shave my arm, they are sharp enough.

Marv

Re: Hatchets?

#3

Re: Hatchets?

Dean J in MN

>I have one in my shop. It is amazing how handy a hatchet is to have around. I tend to grab it when I need to quickly even off a rough edge (rather than picking up a rip saw) or when I need to rip off just a small amount. You'll find lots of use for a hatchet. Tapering stock and quickly roughing curves, etc.

-Dean

Re: Hatchets?

#4

Side axe

Greg B�tit, Vergennes VT

>I've got a hatchet sized broad axe- the cutting edge is beveled on one side like a broad axe. But the handle is straight. I use it for rough straightening small pieces of stock- mostly green, riven pieces not quite tame enough to go to the shaving horse. The stock is usually small enough to hold vertically and chop down on it.

greg

Re: Hatchets?

#5

Scary Sharp on a stick...

Alan DuBoff

>Brad,

I only have 2, one small hatchet and one broad axe, but I grind the bevel close enough, and use sand paper wrapped around a stick, just like I do for a drawknife. Scary Sharp on a Stick!

Re: Hatchets?

#6

St Roy loves his!

Glenn Madsen, near San Francisco

>

Re: Hatchets?

#7

Re: Hatchets?

Adam Cherubini

>I have a few hatchets and use them often. If you keep them sharp, you can pare with them by holding the poll.

I certainly do hew off edges. One thing I never do is raise the blade above the hand holding the stock. I always have one hand on the hatchet and the other above. So when hewing off stock, hold the top of the workpiece and chop from the middle down, then flip the work. Its amazing how few people do this.

This isn't just a safety issue. Its an inhibition issue. If you are worried about loosing a finger, you won't be as aggressive. I also tell folks to forget whatever they used to know about hatchets. Our boy scout hatchets weren't as sharp as kitchen knives. Extra care is helpful.

Adam

Re: Hatchets?

#8

I Beg Your Pardon...

Stephen Shepherd in the State of Deseret

>My hatchet is an ax. Well one of them is actually a tomahawk, European Poll, laminated steel (an old file) in wrought iron (an old wagon tire). Use it all the time to trim stuff down. And like Adam says don't cut toward anything you don't want to cut off!

I also use an ax that I am not sure how to describe. It is made in Sweden but is more like an English Battle Ax. Nasty looking thing, thin blade, big bit, huge poll and a short handle. Works great for wood that is intimidated by a big ax.

In the market for a coopers bench ax, I have owned a few and they are indispensible for many projects, sharpened like a broad ax, single bevel.

Double beveled axes, bench axes, hatchets and tomahawks are tools that I am not concerned about a micro back bevel, but I can use my thick rulers.

I sharpen all of them with a file and if they are too hard, there is always the stove.

Stephen

Re: Hatchets?

#9

Re: Hatchets?

Todd Hughes

>I used to make small axes and used a hatchet a good bit to shape out the handles.

... I see lots of old tools but finding the right hatchet that I liked I found out to be far from easy. In my experance most you see are to large and heavy for work like this and also many esp. newer vintage ones have to soft of an edge. I wanted somthing that had a single bevel 3 inch edge and weighed around 1 - 1 1/2 lbs.. I think any hatchet used for wood working like this that you can sharpen with a file is to soft...you wouldn't want a plane blade or chisel with an edge that soft would you?

Finaly settled on a small , about half normal size, hewing hatchet and a very small double bevel lathing hatchet which I used the most probably because it was so light and handy.

I guess it boils down to what you are going to be doing with them but I think all wood workers should have a good hatchet...think they will find it usefull ......Todd

Re: Hatchets?

#10

Re: Hatchets?

Adam Cherubini

>I agree Todd. I like I light weight hatchet with a broad but thin edge. I found an oldie like this. I wonder if any enterprising smiths are making hatchets like that now. Have you ever examined those Gransfors hatchets? What do you think of their work?

Adam

Re: Hatchets?

#11

$10

Brad in Ottawa

>Todd,

Picked up exactly what you described for $10. Maybe you do live in Old Tool Hell!

Re: Hatchets?

#12

Small hatchet/axes are around...

Alan DuBoff located in NorCal

>Adam,

We use one very similar to what you folks are describing at the smithy I occasionally frequent. We use it a lot to chop kindlin' for the forges, but also use it exactly how you describe, on the side of a board.

Scott Thomas runs the smithy and is there several days a week, send me an email if you'd like to contact him, he also made a very nice mini-adze that is very handy and useful for working wood. Scott does very nice work.

The hatchet pictured below is very light, about a 1 - 1.5 lb. head, with a handle rived from a tree at the historical farm where the smithy is located.


img

Re: Hatchets?

#13

Thats a Tomahawk

Todd Hughes

>...Have made many, many dozens of them.

... Usualy a poor choice for real wood working,... more of a primitive all around tool. Not having a poll and a large round eye tends to make it wobble more when cutting then a regular small axe or hatchet.Not having any weight behind the eye I think makes them less efective then a simular weight regular axe, don't know at least that was what it seemed like to me when I used them.

... Also most are very soft because they are made as a general purpose tool that is likely to see abuse, many are made for throwing so of course they have to be very soft for that.

Are easy to replace thier handles though....Todd

Re: Hatchets?

#14

Re: Hatchets?

Todd Hughes

>I actually have a Gransfors, it's thier Hunter model, I bought it at a flea market for $25 and was just about mint complete with it's sheath. Have to admit when i bought it I was figuring on selling it but I really liked it and after using it to cut up a tree that fell in my drive way think I have decided to keep it [maybe]. It really is a very nice made high quality axe, not as well finished maybe as an old axe but still very well made I think. I like the handle esp. I don't think I would ever buy a new one for what they go for but that is me. I don't know about other models they make but mine isn't really what i would consider a wood working tool

At least on mine the blade is pretty hard and thin so takes a great edge. I think though if you looked around you could pick up an old Collins Hudson Bay half axe for lots less that would be just as good......Todd

Re: Hatchets?

#15

Maybe tomahawk, but it works well...

Alan DuBoff

>Todd,

This actually does work very well for woodworking, although I admit that I have only used it for a few small things other than kindlin' to fire up the forge, but it works very well, IMO.

What I like about it is that it is light, easy to manipulate, and holds an excellent edge...I think it's just some old 5160 steel, maybe from a coil or leaf spring.

I'd sure like to see you fire up your forge and start getting your arm back in shape, you have the skill and talent to make excellent tools.

I'll linky to a page where you forged a hewing axe, but to me it is very similar to what you call the tomahawk above, even looks like the eye was forge welded in a similar way. although, I see you used a grinder to remove material and I think Scott did all of the work in the traditional way, forging and hand filing. Still, a very nice axe you made there, apparently in a time before Amy-Cupcakes and Ms-Jazz got their grips on 'ya...*grin*

Maybe Adam can inspire you to fire up the forge and make him a nice axe.


img

Re: Hatchets?

#16

Different

Todd Hughes

>Actually the Tomahawk is made quite a bit different then the axe I made in the picture. A Tomahawk head is made out of one piece which is wraped around a mandril to form the eye and then welded in the front, if it is made out of iron and you want it to take an edge you have to weld in a steel bit for a cutting edge.Originaly many cheap early trade tomahawks probably didn't have a steel bit in them. Today many tomahawks are probably made out of low carbon steel esp. if for throwing

The axe I made is made out of 4 pieces, two iron side pieces with the ears shaped in, a 3rd iron piece for the poll and then the steel bit. All forge welded together in my old hand crank coal forge. In this particular axe since it was a small single bevel hewing axe the steel was layed on the bottom. On a normal axe would be put in the center between the two side pieces. The eye on this axe is rectangle and tapered smaller on the bottom, a Tomahawk's is normaly round and bigger so that the handle could be slid down from the top.

... Beleve the only thing I ground was the cutting edge the rest was forged finished. Even in the 18th century I think most axes like this would have had at least thier cutting edge ground maybe on hand turned wheels with many shops doing lots more grinding with large powered wheels.

I think the idea of the old 'smith finishing his axes with just a file is probably more romantic then factual esp. when you think of the wear on the files from filing hard scale off the forgings, the espense of the files, and the availabilty of grind stones. Remember too these guys got paid by the axe and wanted to finish them as fast as possiable.

I am getting my new shop set up and hope to get back to doing some more blacksmith work. Don't see me ever taking orders for making anything...to much like work for a lazy slow head like me! I recently forged out some 18th centuruy Knitting needles for Leigh a few weeks ago and really enjoyed making them as well as the wooden, ivory and silver knitting sheath to use with the one. She tells me I could make knitting needles and sell them...I told her I'll do that when I die and go to hell .......Todd

Re: Hatchets?

#17

Historic Rant

Stephen Shepherd in the State of Deseret

>Lewis and Clark and the Corp of Discovery only carried ax heads thinking they could find suitable wood along the way, having no idea where they were going. As it were when they needed handles for their axes to make the ribs for their folding iron boat the choices were cottonwood and choke cherry, they chose the latter. After breaking a dozen handles in an hour or so, the going was slow. Lewis later commented in his Journal that he wished they had brought the European style (round eye) instead of the American pattern (rectangular eye) as they would have been easier to replace the handles. They never did use the boat successfully.

That is not my Rant, but I thought I would share. What I want to talk about is throwing tomahawks. I am convinced that this is all from Hollywood. Now I have thrown tomahawks, I was a mountain man once and it is a popular modern sport.

Did people throw axes in the past. Perhaps, a friendly competition but I haven't seen much documentation to indicate that it was a common occurance. For one thing it is terribly hard on the edge (which they would use on a regular basis and have to resharpen on a grindstone) it was also hazardous to the handle.

As for throwing an ax as a means of self defense I can not imagine a person in their right mind throwing away their weapon. If you missed, your enemy could pick it up and kill you with it. In each and every case you can chop at them providing you haven't thrown your ax away.

Throwing a tomahawk is actually kind of fun as long as it doesn't lead people to think that it was a common historic practice.

There I am done.

Stephen

Re: Hatchets?

#18

How do you feel about Snow&Nealey?

Bob Hackett

>

Re: Hatchets?

#19

Re: Historic Rant

Todd Hughes

>I have read several historical accounts of tomahawks being thrown in combat, interestingly all of them I believe were by Indians and everytime they missed. Seemed like more of an act of desperation then some real tactic...sort of a hail mary pass. Have read about where Indians in camp would practice throwing hawks at trees and were very skilled at it.

Of course if you have thrown many axes you know how important it is that you do it from a fixed distance...a target running away or toward you I would think would be very difficult to hit. Certainly right thinking that you would not throw your weapon away either...don't think many bayonet muskets were thrown like spears either.

Interesting but the blacksmiths with Lewis and Clark made a type of large unbalanced all iron tomahawk called a Missouri War Hatchet to trade to the Indians for corn. Even though not a very effective weapon [and certainly not tool] the Indians wanted them because they were large and showy and picked them over more useful types ....Todd

Re: Hatchets?

#20

Lewis' Journal Drawing 

Stephen Shepherd in the State of Deseret

>


img

Re: Hatchets?

#21

Ah, I do see now the welding differences...

Alan DuBoff

>Todd,

Missed the fact that you forge welded a piece of tool steel on the back, but now understand what you did there, the left side shows how that is done...

We do usually use a sandstone wheel at the smithy, and I would use a grinder at home myself most likely, or hand file it, that always works albeit a bit slow.

Scott Thomas does everything with a hand cranked coal forge also, as was that tomahawk.

Hope to see some of your work, glad you're getting shop setup, you have a lot of skills that you can put to use, IMO.

I cherish that old POS saw you gave me, which looked like Helen Keller filed it on a pogo stick...if for nothing else but to know that I am in a special select group of folks that have ever gotten a b-day gift from you...LOL! Funny thing is that the handle is epoxied on, and both screws are stripped, but the handle is solid, it was re-toothed, and actually a very usable little saw. It reminds me that you are genuine person, even if I do annoy you...;-)

I do hope to see some work by you, the world can use more smiths! Still willing to buy that nice hammer you forged a year or two back, with the ugly chasing handle on it...hehehe...

Re: Hatchets?

#22

Re: Historic Rant (about the settlers...)

Alan DuBoff

>Ok, since you guys are ranting, I have to toss my rant in the ring...

I find it amazing that the Indians for the most part have never been smiths, and I suspect it might have something to do with the way they viewed fire, in the sense of a power/GOD or spirit. But it is amazing to me that they never really forged. Indians like Ned Christie were doing it as an act of labor for the settlers to gather their skills (i.e., the ones that did forge).

The most amazing thing is that the settlers produced forged weapons which they traded to the Indians, who in turn used those weapons on the very settlers that traded them. This is all akin to the Iran contra involving Ollie North some years back with watergate and such...

Most all of the peace pipes were made of the red stone from Minnesota as I recall, or other soap stone. I know you have forged peace pipes in the past, those are way kewl...yet another product that was forged and reintroduced to the Indians by the settlers.

History has a funny way of running circles around our lives...

Re: Hatchets?

#23

Re: Ah, I do see now the welding differences...

Todd O. Cronkhite Maine Native, Presently Away

>I cherish that old POS saw you gave me, which looked like Helen Keller filed it on a pogo stick...

That wouldn't by chance be the World Famous little saw that Todd made out of a genuine Maryland grain shovel would it?

I have a little hatchet that Todd made for me back in '01 IIRC. I also cherish it quite dearly. Would make for a good hotdog chopper, but I love it to pieces anyhow.

I'll try to post pics of it sometime tomorrow if anybody would like to see it.

T.O.

Re: Hatchets?

#24

Re: Ah, I do see now the welding differences... *LINK*

Alan DuBoff

>----

That wouldn't by chance be the World Famous little saw that Todd made out of a genuine Maryland grain shovel would it?

----

Oh no, don't I wish. That sounds like a classic, mine was just an old saw that someone tossed in with some old rusty tools. It was really bad looking, but in some ways cooler than the saw I bought from him, it has more character.

I just snap'd some pics of it at the linky.

----

I have a little hatchet that Todd made for me back in '01 IIRC. I also cherish it quite dearly. Would make for a good hotdog chopper, but I love it to pieces anyhow.

----

No crap? That's a keeper, he rarely fires up the forge, if you want to trade it for something, let me know, I'd love to have one of Todd's rare pieces of hand wrought iron. A couple years ago he did a cool hammer, mostly in spite of the Japanese, but it was very tastefully done, and you could tell that Todd knows how to move metal, but again, it was a rare piece and he wouldn't sell it. I kidded him about the handle looking like crap, as I don't care for chasing hammer handles, but it was usable...hehehe...

----

I'll try to post pics of it sometime tomorrow if anybody would like to see it.

----

Oh, please do, I'd love to see it. It's a shame he doesn't forge anymore, I always try to give him a kick to see if he'll fire up the forge, but alas, he's distracted by Ms-Jazz, Amy-Cupcakes, and Leigh, but they have something to offer Todd that a bunch of dirty coal soot doesn't...

Truth be told, I struggle to forge a turdlette, although some of my work is starting to look less turd-like, and I have gotten more comfortable with it, but can't move metal like someone who's done it for any substantial amount of time...I have fun with it though...

You can see the mood saw at the pics, spin the slots depending on your mood, cuts straight, and true, even though it's fugly! *grin*


Birthday Mood Saw

Re: Hatchets?

#25

My Birthday Mood saw in "as-found" condition!

Alan DuBoff

>ToddO,

A rare and slightly misleading photo of my cherished b-day saw ToddH sent me, pre-Mood change. It didn't become the mood saw until I busted it's nuts, I'm good at that...;-)

Although you can see how bad the teeth are at the heel of the blade, you really needed to see this saw in the raw to appreciate it. Toe is also has the classic bend, from trying to waltz on the floor...That has been fixed mostly.

Face it, if it was worth more than a $0.25 to Todd, he probably would have tried to ebay it. *grin*

I will trade it for your axe? *gd&r* (throw in a really cool saw with it...actually, do you like Disston saws? Cause I hate most of 'em...I would trade a few good Disston backsaws...would make it a very nice deal if you like Disston saws...;-)


img