Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Mortise Chopping Query

Posts

Re: Mortise Chopping Query

#26

Re: Mortising over a bench leg

Barryvabeach

>Bill, I have a reasonably thick bench top, directly supported by maple stretchers that are probably 2 " x 4" thick - even so I found that mortising goes faster when the part to be mortised is directly over the leg, less so when over a stretcher and even slower when on the benchtop away from a stretcher. Stealing an idea I saw elsewhere, I used a square to layout on the top of the bench where the front two legs are and then inset contrasting wood at the corners of each of those points for each leg so that I can quickly locate the mortise direclty over one of the legs.

Re: Mortise Chopping Query

#27

Re: photo - hand screw 

paul womack

>


img

Re: Mortise Chopping Query

#28

Re: photo - 2 clamps 

paul womack

>


img

Re: Mortise Chopping Query

#29

Re: usage note

paul womack

>The reason I recommend the handscrew approach is because the workpiece can be removed/fixed by simply turning the handscrew handle; workpiece in one hand, turn the handle with the other - easy.

The twin clamp approach is OK when it's set up, but a little more fiddly for removal/insertion. Depends wether you own some a handscrew or not (they're much less common in the UK than the USA).

Finally, don't use sliding head clamps (AKA F-clamps) for this; use 'C' or 'G' clamps. Sliding head clamps can move under shock and vibration.

BugBear

Re: Mortise Chopping Query

#30

That's the way I do it

Adam Cherubini

>My planing stop/bench dog is 3/4" wide or so. The only advantage of a stop this narrow is that I can often push the workpiece up against the stop, then clamp it as bugbear has shown (without clamping the stop). This is especially helpful for me as I pare out my mortises as Dean has shown. Another advantage of using the stop is that I don't need a ton of clamp pressure on the work piece. I tend to end for end the piece frquently. The result is a makeshift jig, not unlike what Andrew has described.

Anyway, I thought I'd throw that in.

Adam

Re: Mortise Chopping Query

#31

Re: fragile

paul womack

>I guessed as much - (mallet) morticing in a wood screwed vice would kill it rather quickly.

BugBear

Re: Mortise Chopping Query

#32

Re: fragile- (technical mumbo-jumbo)

Adam Cherubini

>Technically speaking, that's not necessarily the case. The wooden screws typically have a larger cross section than steel screws, so that overcomes at least some of the difference in the Young's Modulus (I) as compared with steel.

so for a 3/4" steel bar,

I=.015in4 E=25,000,000psi EI or stiffness = 375000lbin2

for a 1-1/2 beech pole

I=.25in4 E=1,600,000psi and EI = 400,000lbin2

(I don't think the beech is truly stiffer, but the two screws are surprisingly similar in stiffness).

Malleting on top of a twin screw isn't the end of the world. Since my vise's nuts are set back from the front edge of the bench, there was no need to thread the first 3-4 inches of the screws. So you never actually see wood threads and thus there are none to damage. The reaction to malleting is largely taken in the bending of an 1-1/2" dia beech pole essentially. This is probably bigger and stronger than an axe handle. How well this happens has a lot to do with the fit quality, yada yada yada between the screw and teh hole I bored in the bench top.

You could pretty easily mallet on a leg vise screw. Its got a nice direct load path to the floor.

The problem with the metal vises are their attachments. You're probably never going to damage the vise screw itself, but eventually you could yank the attach screws out of the bench. The stronger vises have a face plate that screws to the bench front as well as an integral bottom. That allows the front screws to only take shear (which they do best). Vises that attach to the bottom of the bench top only force malleting loads to come out as a couple, placing the screws near the front edge in tension. So these should be the big bombers or be thru bolted if you need a really strong vise.

Its interesting to note that blacksmiths, who routinely beat on their vises, essentially copied the wooden leg vise design in their post vises. Nothing beats direct load paths.

Despite this mumbo jumbo- and it is mumbo jumbo, I think its bad practice to beat on stuff in your vise. I think its similarly bad practice to crank down on a vise as hard as you can. With this in mind, any vise can work.

Having run the numbers, I guess I'm a little surprised that the wooden screws appear NOT to be fragile.

Adam

Re: Mortise Chopping Query

#33

Re: Mortising - how to attach to bench

Ted Shuck, Centennial, CO

>This is how I do it as well. I have found that I tend to get wood chips that drift underneath and I need to clean the area frequently to avoid "dimples" in the backside of the piece I am mortising. If I use other clamps on the bench, it is more difficult to keep the area clean. The holdfast is ideal for this since it is so quick to place and does not clutter up the bench top.

Ted

Re: Mortise Chopping Query

#34

Re: thread...

paul womack

>(points accepted and snipped)

Having run the numbers, I guess I'm a little surprised that the wooden screws appear NOT to be fragile.

In beam strength (as you calculated :-) I agree.

I've not seen any snapped wooden bench screws.

The problem with a Youngs Mod. analysis is that wood isn't uniform.

And the damage I've seen to woodscrews (old benches come through my local auction sometimes) is always stripped threads.

In a long-grain screw, the threads are V shaped bits of wood attached by short grain.

To analyse this you'd need multiple values for the YM taking into account grain direction.

BugBear (who also likes blacksmith's leg vices)