Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

shooting board plane

Posts

Re: shooting board plane

#26

You got it!

Scott Burr in Ben Lomond CA

>You wrap your hand around it instead if "pinching" the side. It's larger than I thought it would be, but I have no problems holding on to it.

I think you'll enjoy it.

Re: shooting board plane

#27

Damn you Scott.

Paul Kierstead

>That is the answer to my hand cramps using it. Now I gotta pay up. Well, the g/f will be happy it isn't another plane at least.

Re: shooting board plane

#28

Thanks Norman I'm off to modify mine

Bob Fawcett

>

Re: shooting board plane

#29

Re: stop design

Bob Fawcett

>What wood did you use?

Is it less prone to tearout at the rear of the fence?

thanks

Re: shooting board plane

#30

Re: shooting board plane

Bruce Branson

>Very good article.I going to make some this week.

Re: shooting board plane

#31

Coming in late here Bill, a No6 is sized perfectly

Andrew F in Australia

>Hi Bill,

This is a good job for a plane about the size of a No.6.

Others will quote me on the fact that I use the No.6 for 98% of all work, but this is one job it excels at.

Sorry if this is redundant info. I haven't read the other posts - been working and 300 here and 600 on the other board when I've got the idle 10 minutes to check in.

Cheers,

Andrew

Re: shooting board plane

#32

Re: my (different) thoughts

paul womack

>My reasoning for this was probably to have a replaceable fence

without needing to realign the whole fence perpendicularly to the edge of the shooting board.

OK. That's good.

If you have elongated slots in this hardwood strip, you can adjust the fence further right when and if it wears down. Also, this piece of hardwood is much harder than the maple backer.

That's also good.

Neither is the reason I thought of. With this 2 piece design, you could screw/glue down the (maple) backer quite inaccurately. Any error in perpendicularity can be easily compensated for by removing the face piece, taking a judicicious shaving or two, and replacing it.

Or you could just insert shimming.

This make the 2 piece fence by far the best I've ever seen for fine and accurate adjustment. And it's easy to build. WOW.

BugBear (who WILL use this design)

Re: shooting board plane

#33

Re: Agreed.

paul womack

>

Re: shooting board plane

#34

Re: my (different) thoughts

Norman (Metcalfe, Ont.)

>Paul,

That's in essence what I have been doing. Thx for putting it into words. I have needed to remove the dark face piece to get it just right, with as you say, judiciously removing a shaving or two. The maple backer was aligned fairly well, but I can see the benefit of setting it up quickly and instead squaring the dark hardwood front piece.

I can leave the maple piece in position. Removing the rear maple piece a few times can cause issues with mounting holes being enlargened, also it would be not wise to glue it down, etc..

Norman

Re: shooting board plane

#35

Re: Three cheers for the underrated No. 6 !

Norman (Metcalfe, Ont.)

>

Re: shooting board plane

#36

Another way

Derek Cohen (in Perth Australia)

>Hi BB

Another way of ensuring an accurate fence is to make it (micro-) adjustable. Below is a picture of the mod I made to mine. It does not adjust much, about 1/4" in all, but I believe that this is better than using shims to true up a fence. I am still able to attach the add-on mitre fence.

Regards from Perth

Derek


img

Re: shooting board plane

#37

Re: Another way

paul womack

>Derek; what size/direction are the bolt holes/slots?

BugBear

Re: shooting board plane

#38

Re: Another way

Derek Cohen (in Perth Australia)

>BugBear

The pivot is a 3/8" bolt (in a 3/8" hole), while the adjustment comes from a 3/8" bolt/butterfly nut in a 1/2" hole. This makes for 1/8" of adjustment at this point of the fence (probably closer to somewhere in the region of 1/4" at the extreme end).

I built this fence about 6 months ago, and it has maintained its setting in spite of some hard use.

Regards from Perth

Derek

Re: shooting board plane

#39

Re: Another way

paul womack

>I was thinking (before I saw Norman's idea) of this:

With wingnuts at both stations.

BugBear


img

Re: shooting board plane

#40

Re: Another way

Derek Cohen (in Perth Australia)

>That's clever BB! I do like Norman's idea of a replaceable hardwood front to adjust for wear. Your configuration could do this as well.

On reflection, I think the best combination would be my existing fence together with a sliding front piece. Any alterations that are caused by the front piece are easily dealt with by the adjustable rear section.

Regards from Perth

Derek

Re: shooting board plane

#42

Re: Plane selections for the shooting board

David W. Dougherty

>I use something very similar for planing the ends of tapered violin fingerboards. Works great.