Any recomendations for books or videos ...
Steve in Fresno, Go Dogs
>on tuneing hand planes.
Thanks
Steve
Knowledge You Can Build On — Est. 1998
Any recomendations for books or videos ...
Steve in Fresno, Go Dogs
>on tuneing hand planes.
Thanks
Steve
Re: Any recomendations for books or videos ...
wayne anderson
>David Charlesworth is the master at doing and teaching on the subject. Use your search engine to find his work on this. I have his book titled, "David Charlesworth's Furniture-Maiking Techniques". It has a chapter on all the fettling tips and techniques you will likely need. I do believe he has other printed works and videos specific to subject as well.
I would strongly encourage anyone who is serious about using handplanes to read up the the proper tuning of a plane. It will make using one a joy, rather than a task.
Wayne
Also check the articles *LINK*
Dan Donaldson
>Look in the hand tool section of the articles page. There are at least a couple of articles on tuning planes. I am attaching a link to one of them.
Dan D.
Handplane tuning
Re: Any recomendations for books or videos ...
Brent Smith
>Taunton video......Handplanes in the workshop with Mario Rodriguez.
It's a good place to start.
Also Jim Kingshott's Handplane video.
Brent
Re: This One is Pretty Good...
M Meier
>Reclaiming Flea-Market Planes
Re: Any recomendations for books or videos ...
alan womack
>I have Klingshots video and I don't find it adds any knowledge. He loves his english infill and you think you need one after that. Especially if you are a beginner.
Charlesworth gives a better demonstration, and uses a modern production Stanley with a new blade. However, I cannot make it more than 5 minutes before I am SOUND asleep.
I also have several Cosman videos, he has different techniques, but a much better presentation.
Alan
cheaper than sleeping pills
david charlesworth
>Alan,
Oddly it tends to have that effect on me too.
Glad you liked the content, so many videos fall into the "performance" category....
best wishes,
David
Re: This One is Pretty Good...
William Duffield, on the Cohansey
>Hey, Mark, Where you been hiding? How's Benson?
Re: cheaper than sleeping pills
arw01
>I heard from Rob you were working on a third video?
Something I noticed in Klingshots and your video, is you both seemed to use relatively tame wood. I would love to see the experts tackle some of the nasty walnut crotch or an exotic so we mere mortals know really what to expect and what we need to do.
Any chance of making a longer video of say a couple hours on making a piece of furniture. The little woodworking shows at 30 minutes just don't get into it enough. It would be enlightening to "look over the shoulder" of a master from initial concepts, maybe a commissioned piece, to the last rubs of the finish.
Alan
Hey Mark, nice to see your name again
Bill Houghton, Sebastopol, CA
>Good to see your post.
Clean 1st, sharpen 2nd
Bill Houghton, Sebastopol, CA
>I have yet to spend a lot of time flattening the soles of my handplanes and doing all the other careful tuning. I recognize that I'm probably missing out on levels of performance, and will probably do all that when retirement brings me a greater supply of round tuits, but up til yet, cleaning the plane and getting the iron sharp (the latter is harder than it sounds) have been enough.
I did have one plane that was seriously out of flat, but I cured that problem by giving it to my brother.
Re: This One is Pretty Good...
M Meier
>Hey William,
I've been hiding in the world of 3D computer graphics. Years ago that's where I spent all my time. A few years back I became completely burned out and took time off. That's what gave me all the free time for building and hanging out on Badger Pond. Now I'm back in the graphics world (developing animation tools for next-gen games). Consequently I have less time for woodworking. I pop in to WoodCentral to lurk occasionally - it's great to see so many friends still here.
Benson is good - getting older and slowing down though.
Mark
Re: Thanks, Bill
M Meier
>
Sign me up
Jim in Burlington On
>I'd buy a video of a piece of furniture bieng made my David. I learned so much years ago watching Kelly Mehler's video of making a shaker table. Project oriented video's on DVD format that could be watched while at work on the DVD drive while other boring tasks are going on hmmm....... could be a big seller
Bill...Has your brother miffed you ?
Joe Rogers, Northern Virginia
>One way to reduce competition on the slope huh? :-)JR
No, he's a great friend
Bill Houghton, Sebastopol, CA
>but he imagines working wood more than actually doing it, so his ownership of a plane is a symbolic act rather than a real one.
Re: cheaper than sleeping pills
paul womack
> would love to see the experts tackle some of the nasty walnut crotch or an exotic
The only difference would be in effective cutting angle (so either high angle bevel up, or back beveling in bevel down). All the other tuning techniques are the same for mild-to-wild; so I don't think it would add anything.
BugBear
Thanks for all the responses...
Steve in Fresno, Go Dogs
>
Re: cheaper than sleeping pills
Bob Fawcett
>OK. I am currently working on some Cherry for a table top. I have the pieces glued up and am smoothing the top. I want to leave it a handplaned finish, and not use sandpaper if I can. I have 2 good planes, an LV LA Jack, and the BU smooth. I have been planeing for a couple of hours. I have relatively good finish and a fairly smooth top, but there are still some parts I am not completely happy with. Some areas the grain reverses, and when it does the surface is not as smooth as the preceding area. I can see a look like white powder on the surface. I think it is some very minor tearout.
I have several of David's books and videos which I have studied and I have The Handplane book by Garret Hack.
I have the irons in the planes as sharp as I can make them with my King Gold water stone. I can get see-through shavings and the plane glides through the wood like David's did in the video. I don't think sharp is my problem.
Any advice is welcome.
What's next, the cabinet scraper?
Bob have you tried...
Ted Owen, Pittsburgh
>following up planing with scraping? You can go any direction with a scraper--though for the life of me I can't understand why a scraper would work any differently from a plane in this regard.
If you like, then skip the sandpaper. Frank Klausz recommends using sandpaper after scraping, and that's what I do, but others don't consider it necessary. On one of his older Taunton Press video's--it might be Finishing--he uses a scraper on a knot, with remarkably better results than the previous step of planing (an Ulmia or ECE brand smoother,IIRC).
Best, Ted
Re: Bob have you tried...
Bob Fawcett
>Thanks Ted,
That was my next stop. I just wondered if there is some part of this plane thing I am missing.
Re: cheaper than sleeping pills
paul womack
>an LV LA Jack, and the BU smooth
What blade bevel angles? Blades are interchangeable between your 2 models, so any blade investment will be quite versatile for you.
An extra blade with a 48 degree bevel (for instance) would give a 60 degree effecttive cutting angle, which should eliminate tearout, at the cost of a less good surface.
You always want the lowest effective angle that stop tearout, which may be, by conventionl standards, a rather high effective angle.
BugBear
Re: darn!
paul womack
>I now notice from Lee Valley's site on the LA jack page that the blades can be supplied with 25, 38 and 50 degree bevels.
The smoother page doesn't list the 25 option.
Of course, these angles are starting points. Bevels can be altered, although buying the right blade will reduce the effort involved.
BugBear
Re: darn!
Bob Fawcett
>I have the 25 and 38 degree blades, and I was using the 38 in both planes.
Re: darn!
paul womack
>I was using the 38
Which takes you to 12+38=50 degrees effective, only 5 degrees more than a normal Stanley. It might be of interest to go higher.
BugBear