Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Just When You Thought It Was Safe To Go Back In�

Posts

Re: Just When You Thought It Was Safe To Go Back In�

#26

Re: An Article, right???

William R. Duffield on the Cohansey

>If you sic the WC article crew on in, it will be. They are welcome to use my text and photos, and edit it to their hearts' content. The same goes for anything else I post on WoodCentral. However, the text and photos should not be used for commercial purposes outside of WoodCentral. Some of the other points of discussion should be included as well. Note that the photos are not currently on the WC server, so someone will have to copy them from my aol account. Any time you see a post, or even several posts on a common subject, that you think is worth keeping, you should send e-mail to Ellis and probably to Garrett Lambert too, nominating it for posteritization. Building the framesaw, testing it, photographing it, uploading the photos, writing the post, and answering responses is already enough work. I'm going to let WC's professional editorial staff do the rest of the work if they want to.

Re: Just When You Thought It Was Safe To Go Back In�

#27

Thanks, Sir William

Dan Donaldson

>I got it saved for editing. Will have to look at the responses on the thread to see which ones would add something to the article.

Re: Just When You Thought It Was Safe To Go Back In�

#28

Re: Veneer Saw Construction (LONG!) *PICS*

Christof Hartge

>Hello Tod, Ted and Williams,

thanks for your responses and the simple explanation for the belly-blades.

To the position of the stretchers: Intersting enough Lachappelle made their veneer saw exactly as Ted uses it now: They are fitted not movable in a distance of probably 7". I speculate the reason for this may be this: It provides more stability for the saw along the horizontal axis: it is easier to steer the heavy saw.

I destroyed a piece of larch too in the first attempt to resaw ( with a bow-saw). I learned in the second attempt: Althougb this is tedious work you still have tob more than sensible if the saw starts to bind. If it is so immediately go back in your cut history and try to correct some inches before your actual cut. Second I learned to cut the center at last. So try to work from all for corners, using the last cut as jig. That means and this is the third rule I figured out for me, change the angle of cutting slowly cut by cut and not abruptly. If I changed it immediately the saw was free to choose away slightly diffeent from the given cuts and started binding.

Greetings, Christof.

Re: Just When You Thought It Was Safe To Go Back In�

#29

Re: Veneer Saw Construction (LONG!) *PICS*

Ted Shuck

>Christof,

You have given very good advice here. I have found exactly the same things, through trial and error.

I find that the most difficult part is usually getting the cut started squarely on the corners. I do this with a tenon saw. Saw about 1/2" (1cm) on one side of a corner, then flip the saw to the other side. Keep doing this until there is a good cut for about 2" (5cm) each side of the corner, then switch to the frame saw.

It is not hard to keep sawing to the line on the side facing you with the frame saw, but it is very easy to get off the line on the side away from you! I have found that it helps me to saw at a low angle to the side that is facing me, establishing a kerf in that edge without cutting deeply in the side away from me. Then flip the board around and saw the same way in the other side. Once these kerfs have been established, it is much easier to connect them by sawing through the center. The kerfs tend to keep the saw blade from wandering too much. This is very much like the technique for sawing a tenon face.

I hope this makes sense to somebody!

Ted

Re: Just When You Thought It Was Safe To Go Back In�

#30

Re: Keeping the Frame Saw on Track

William R. Duffield on the Cohansey

>That is welcome advise. It makes sense to me. A perhaps amusing story: The reason I finally got around to making my frame saw was because I had a project that I couldn't figure out another way to do with the "resources" available. I needed to rip a recycled 6x6 timber down to 3x3, and it was way too big for the power saws I had available to handle. Since it was over 16' long, I couldn't accurately push it through the saws by myself, anyhow. I realized it would take me several days to rip it by hand with the other saws I had available. At the time, I was still looking for the D8. Even with the frame saw in hand, but without the grips, I quickly realized I was having trouble making progress and sawing to the line. One doesn't flip a long 6x6 over every couple of inches to check that you are sawing straight, especially with a frame saw stuck in it between horses. So I did the modern equivalent of your suggestion, and cut kerfs in both surfaces with a circular saw. Needless to say, when that part of the job was over, I was glad to turn that thing off, take off the ear muffs and goggles, spit out the sawdust I was chewing on, and get back to the frame saw. Now, it tracked well, and since I had removed a good bit of the thickness, the remainder of the job went relatively quickly.

Re: Just When You Thought It Was Safe To Go Back In�

#31

Re: Keeping the Frame Saw on Track

William R. Duffield on the Cohansey

>Hmmm.....

If you didn't want to emulate a backslider like me, I suppose you could cut the guiding kerfs with a plough plane equipped with a very narrow cutter.

For the pine and that untuned Putsch blade, I'd have a hard time finding another saw in my arsenal that would cut a kerf wide enough to help it track :^)

Re: Just When You Thought It Was Safe To Go Back In�

#32

Re: Keeping the Frame Saw on Track

Christof Hartge

>No you won't find another saw unless it is another bow-saw blade out of German production. Out of no obvious reason they give them way too much set. I usually bend them back with a pair of pliers and give them a small set again. This increases the performance dramatically.

Christof

Re: Just When You Thought It Was Safe To Go Back In�

#33

Re: Keeping the Frame Saw on Track

Ted Shuck

>I removed almost all the set from my Putsch blade by tapping it wout with a hammer over a flat surface. The blade doesn't need as much set as a regular handsaw since it is relatively narrow. If all the set were left in, it would be *really* hard to make it track straight!

I like the idea of using a plough plane to establish the initial kerf. I just need to find one narrow enough. My Putsch blade is about 0.040". Thick for a framesaw, but very thin for a plough blade.

I have been using mine to resaw 4/4 stock for making small boxes. One other thing I have learned is that I waste much less wood if I saw the boards to approximate dimension before resawing. It seems the longer the distance I have to resaw, the more potential I have to screw up. If I am only sawing about a foot at a time, I do a much better job.

Ted

Re: Just When You Thought It Was Safe To Go Back In�

#34

Now I'm really sorry ...

Raymond in Trenton NJ

>... I missed dinner with the CJWA crew. It would have been neat to play with the waitstaffs heads by eyeing up the tables while you were weilding your saw. Your posts get better and better Bill. Thanks for the info, lesson and suggestions for frame saw building and thanks to all the other responders for providing additional imput ... even that Wiley character on the left coast :o)

Raymond,

who really has no excuse for not finishing his bow saw. Well, maybe one excuse ... it's not started yet.

Re: Just When You Thought It Was Safe To Go Back In�

#35

Re: Veneer Saw Construction (LONG!) *PICS*

paul womack

>I've seen photos and discussion of a Galoot-made veneer saw. I thought it was an interesting design, as the stretchers were adjustable in slots in the arms, so you could move them towards or away from the blade, depending on the thickness of the veneer you wanted to cut.

That sounds like

Paul Perrons' saw (bottom of page)

BugBear

Re: Just When You Thought It Was Safe To Go Back In�

#36

Re: Frame Saw Construction (LONG!) *PICS*

paul womack

>I would recommend coach bolts as the "raw material" for the tensioners. If you hacksaw away the edges of the domed head (following the faces of the square zone just below) you have a nice rectilinear end for working your blade attachments, a nonthreaded portion to pass though the arms, and then a threaded zone for tensioning. Sounds pretty ideal to me.


BugBear

Re: Just When You Thought It Was Safe To Go Back In�

#37

Re: Frame Saw Construction (LONG!) *PICS*

William Duffield on the Cohansey

>Yes, if you know exactly how long to cut them, carriage bolts, or even long hex head machine bolts with only an inch of thread would work well. It makes it a bit easier to install the blade and tensioning mechanism into the frame. However, as I was developing the saw, I was working from the inside out, and I was not sure exactly how long they were going to need to be. If you cut them a little too long, you run out of thread before you get the blade tensioned enough. Also, I had lots of allthread available, and it is usually cheaper per unit length.

Re: Just When You Thought It Was Safe To Go Back In�

#38

Re: Frame Saw Construction (LONG!) *PICS*

paul womack

>If you cut them a little too long, you run out of thread before you get the blade tensioned enough.

Agreed. But I own a set of dies... :-)

BugBear

Re: Just When You Thought It Was Safe To Go Back In�

#39

Re: Frame Saw Construction (LONG!) *PICS*

William Duffield on the Cohansey

>Doh! Of course, I have some dies too. Why didn't I think of that?

Re: Just When You Thought It Was Safe To Go Back In�

#40

Re: Frame Saw Construction (LONG!) *PICS*

paul womack

>BTW, putting MORE thread on a coach bolt with a die is REALLY easy, since the thread is already started off for you. And starting a die is the hardest part.

BugBear

Re: Just When You Thought It Was Safe To Go Back In�

#41

Then again...

Bob Hackett

>who wants to hang around a guy who`s always dieing?

MB