Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

California Air Tools compressor questions

Posts

California Air Tools compressor questions

#1

California Air Tools compressor questions

I have a California Air Tools compressor, 30 Gallons, and I have it on a timer so I can run it an hour or two here and there.  Yesterday I noticed that it continues to do the little "spit" thing after the power is off, in effect draining the tank completely over time.  (For those who don't know, it spits out a little air every thirty seconds or so to drain the tank of any moisture.)  I sent a message to the company telling them I found this irritating and a waste.  Part of the problem is I had a much smaller compressor before and left it on continuously for about thirty years so air was available.  With this one I decided to add the timer because it finally occurred to me it could blow off a fitting or spring a leak and run forever which would naturally occur while I was away.  I asked if there was a way to reset this feature so I could store and use the remaining air in the tank.  It takes the unit about five (long) minutes to come up to pressure and that's a long wait to drive a few fasteners.  The company sent back and said I should do maintenance on the unloader valve.  That it could be bad to leave a tank full of air for a long period.  Have I made it clear I hate change and new fangled stuff?  I think what I need is a much smaller compressor that would pump up faster.  Any thoughts?


 


Re: California Air Tools compressor questions

#2

Ellis Walentine

Compressors

I lost my shop because of a stuck unloader valve on a big air compressor, and I will never again leave any compressor turned on if I'm not there in the shop with it. I don't imagine that would ever be a problem with a little compressor, but I've had several little compressors and the noise was the deal breaker on all of them. Portability is the only reason I'd have a small compressor. As for leaving air in the tank, somehow I always seem to have a slow leak somewhere -- in the hose, in the quick-change fittings -- so keeping a full tank when the unit is off isn't very realistic, at least for me. I'd keep the California unit and put up with the wait. If you can get the air purging to stop, that's a bonus, but drain the tanks at least occasionally.

Ellis




 






Re: California Air Tools compressor questions

#3

Re: California Air Tools compressor questions

Given the popular wisdom that ensuring there is no water build-up in the tank to cause corrosion problems it seems to me the California unit is doing what it should do, albeit automatically. I believe that intermittent pssssst sound you hear from trucks and buses passing is the same type of device clearing out their air-brake system.

If the main issue is driving fasteners then a little compressor would be a solution.

Another one and it depends on what your fastener driver requires but I have a portable 1o gal tank with a regulator that I can drive brads for a long time before it needs refilling. Of course, this isn't driving 3" framing nails. Since it gets the air from the compressor that has already condensed out the water, the air in the tank is dryer to start with but I do think they have a stated lifetime (10 years?) like a propane tank.

I imagine, if the design permits, you could replace the automatic valve with a ball valve or similar?

Bill


Re: California Air Tools compressor questions

#4

Add this, and keep the other

For when you need a higher volume. This little compressor is quiet and will supply plenty of air for your Brad and finish guns.�

Check this out!

https://a.co/d/2sVzv8Z


Re: California Air Tools compressor questions

#5

Tank Drains

I've used a Wilkerson auto drain on my 60gal. IG compressor for most of 20 years.  It's piped to replace the tank's bottom drain and cycles once during each fill/use cycle with a 15psi pressure drop.  Condensate (oil + water) is blown outside.  It gets cleaned 2-3 times a year, and has kept my tank and air quite dry.  Unfortunately, the model I have has been discontinued.  Grainger lists a similar unit to be available next month for about $150.

When I'm going to be away from the shop for more than a day, I close the main tank valve, flip the dedicated circuit breaker, and close the valves feeding the hoses.  I don't drain the tank.  Most pressure I've ever lost was 2 psi over the course of 2 weeks away during the winter.  My distribution system is all sweated type L copper to 3 air "stations" that have a filter/regulator and a drip leg drain.  Drip legs are checked fairly regularly but have yet to show any condensation in the pipes.


Re: California Air Tools compressor questions

#6

Re: California Air Tools compressor questions

Compressors have had unloader valves since they invented them. Without it, you would need an electric motor twice the size to spin the pump under load. Nothing new fangled about the California tools, they just spin them slower.