Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Table Saw Upgrades

Posts

Table Saw Upgrades

#1

Table Saw Upgrades

Walleye Tom

So, I have this really old table saw. It is a 10" Craftsman Contractor Style. It has this goofy computerized system for raising and lowering the blade as well as angling it. If that ever goes out I am screwed as there is no replacement parts for that possibly 70's "High Tech".

It, of course, has a godawful sloppy inaccurate fence system and a 1hp motor off the back with the Belt. I was thinking about adding a decent aftermarket Fence system to it and a 1.75-2hp motor. I could even run a 230-volt motor as that and the computer part run off of different switches.

So, I have a few questions that perhaps someone might have the answers to. There is no wrong answer or opinions, unless it ends up with me in jail, again.

Are there any other ideas anyone has to inject this old saw with steroids and make it super impressive to the young ladies?

What are your recommendations for a good, not overly high priced Fence system that has a reputation for being accurate?

Also, with an aftermarket Fence system, do you have to build leg stands for it so the Saw doesn't tip over because it doesn't weigh a lot as it has an open bottom stand.

Has anyone ever built a "Custom" Cabinet type stand out of wood for the saw to sit on and maybe large enough for the added wings of an aftermarket Fence? Something big enough for storage and easy dust removal, on wheels, etc.

Has anyone "beefed" up their saw before by adding a larger motor to it? I am thinking more of a Power bump than a speed bump. I would keep the RPM's similar to the original 1 hp motor as I wouldn't want to overload any other parts on it. But that 1 HP motor on there now can get bogged down with some woods.

I know the Aftermarket Fence system will be worth more than this saw, but if I ever throw the saw away, I can use the Fence system on something else. As for the bigger motor, I will find one at an auction or garage sale, I won't buy a new one. And I have a use for the old craftsman saw motor in building a custom dual sander, with one side being a round sanding drum and the other side being a round sanding strip system. I will have to drop the RPMs using a belt and larger pulleys down to about 1300, but it should work fine. Great for Sanding odd pieces, especially Logs. I would get the sandpaper from Sandrite. They sell a system and I have the two different drums already. Grizzly sells one like it too.

That's about it. I sure would appreciate any and all ideas, advice, or expertise you might have. Thanks.

Here is a pic I downloaded of a cool cabinet with a cheapo old Craftsman table saw in it.


img

Re: Table Saw Upgrades

#2

Re: Table Saw Upgrades

Walleye Tom

Here is a pic of that sander I am going to build with the old Craftsman table saw motor.

Whoops, I can't get it to come up because it is in my stored photos. How do you do that when you have a photo on your computer that doesn't have a url?

Re: Table Saw Upgrades

#3

Upload photo

John K Jordan

>>>Whoops, I can't get it to come up because it is in my stored photos. How do you do that when you have a photo on your computer that doesn't have a url?

First, size and compress the photo so the file size is less than 100Kb on the disk. Then click he "Upload embedded file: Choose File" button just above the text box while composing a message.

JKJ

Re: Table Saw Upgrades

#4

Re: Table Saw Upgrades

Bill Tindall, E.Tn.

Quality used saws are so cheap that it doesn't make much sense to be spending money to try to turn this saw into a better one. I am particularly puzzled by the desire to upgrade the motor. A new 2 HP motor will cost what a used quality saw will cost. However, if you insist I have a nearly new 1.5 HP quality motor for sale.

Re: Table Saw Upgrades

#5

First,

Bruce, a MN Galoot

Walleye Tom has to be a registered member of this site.

Re: Table Saw Upgrades

#6

Re: Table Saw Upgrades

Barry Irby

As is usually the case, I agree with Bill.

I have a 45 year old Rockwell contractors saw I bought new. Right after the warranty went out the motor failed. I added a 1 3/4 hp Dayton motor and that has lasted literally forty times longer than the first one and has been a joy in the power department. About ten years ago I caught a Biesemeyer fence for $80 when Lowes got out of the fence business. That has been a joy. Much better than the crap that came with the saw. The only thing I miss is I had already updated the rails so I could saw 35" for cabinet ends and the new fence only goes to 30". And No, I did not build legs under it. I already had a router table built into the wing and I sometimes use the fence with the router, but generally that is not good because it always seems I need to rip something while I have the router set up. So, I have done most of what you talk about, but I still agree with Bill.

Looking at it today, I would go buy a used excellent saw and start over with that. If I could afford it I would look at a Sawstop saw. (Let the storm begin.) This being a Ford Vs. Chevy statement, I BELIEVE my old Delta/Rockwell saw is a better saw than your old Craftsman. I spent many hours "perfecting" the dust collection on that open cabinet. I got to over 90% but it would have been a LOT easier on a cabinet saw. In my mind, you don't have a REAL table saw until you have a Delta UNISAW, but that music has died. I would not want to put this much effort into your saw while waiting for the electronics to die.

Re: Table Saw Upgrades

#7

Re: Table Saw Upgrades

Grant Smith

Hi Tom,

I have seen this movie before in my shop(s).

I went from a 1950's Rockwell Delta radial arm saw, to an early nineties Craftsman contractors saw. I upgraded everything I could, including installing a Biesemeyer Fence on the machine. Arbor slop (and the bearings were replaced with Timkens), and the fact that every time I tilted the blade and returned it to the stop, I would get a different reading somewhere close to 90 degrees meant there was not really much hope.

I sold the saw and bought a Unisaw. As a former machinist, I can tell you that the difference is huge. I can now set the fence, tilt the blade, return the blade, and the saw zeroes out reliably. No more burning, no more fiddling around. To be fair, I have aligned a Sawstop, and they are indeed great, safe, accurate machines. I may one day upgrade. Know that the movement to Sawstop means there are good Unisaws and Powermatics out there looking for a home. Do some searching and offer low.

To be fair, I spent $60 on the old Rockwell, and about $150 on the Craftsman, and maybe $1200 on the Unisaw. Money is an issue for most of us, as it was for me when I made each of these purchases. That said, there is NO COMPARISON between the machines. NO comparison in the fit, build, heft, power, and just plain quality one gets. I used to run thin kerf blades because of the 1.5hp motor. Blade deflection is then an issue if one measures the product carefully. I now run full kerf blades with no issues in that realm.

My advice is take some measurements. Tilt the blade, then return it to 90. Adjust the 90 degree stop, then do it again. Wash, rinse, repeat. If it reliably hits 90 each time, you may have an argument for keeping the one you have and working on upgrades. If not, then sell it to a contractor.

Consider taking on a commission or three to offset the cost of a cabinet saw replacement. Spend the time making projects, not beating a dead horse. No room? hogwash. If you can store a contractors saw, you have room for a small cabinet saw on wheels. No motor hanging out the back makes a difference.

FWIW,

Grant in Iowa

Re: Table Saw Upgrades

#8

Re: Table Saw Upgrades

Bill Tindall, E.Tn.

Agree, the old "contractors" saw was a good piece of equipment, far better than many inexpensive saws sold today.

The very old cast iron Craftsman saws were good saws. They showed up on job sites and performed for decades sawing what needed to be on job sites.

Re: Table Saw Upgrades

#9

Lipstick on a pig?

Gary Smyth

I have to ask. Are you upgrading because you like the setup you have, or perhaps what you built around it, or you want to get something more fitting to your current or future work needs?

How old are you? How much woodworking are you doing?

If you decide that you will use as well as need a better saw, then look to a better saw. Compare that price and value to your years of woodworking remaining. If that works then bite the bullet, sell or donate what you have and get a better saw. The difference of the upgrade can be balanced by the work and the length of years/time you will be using the saw.

If on the other hand, this is merely an exercise to reduce shortcomings of what you own then remember that lipstick on a pig still leaves you with a pig maybe a bit prettier but little additional value.

If you look, you may find a nice saw with a good fence, ready to go, and all that will be required is payment and transportation. In the long run, a good choice.

Additional personal tale: I have a Craftsman 3.5HP router in my router table. It fits exactly in the router plate on a large table. That router is no longer made. To replace it with a different router means a new router, completely new top, new plate, some rewiring and different lift mechanism. My original crapped out two years ago. I hated the additional expense and prospect of rebuilding. Because of ebay I was able to secure one, then two more used same model router for less than the total cost of replacement with new. Now when the next one goes I have exact replacements. With a little luck, these will take me through my woodworking days. It works for me. This alternative is not an option for you. Save yourself now. Look to a new (to you) saw.

Re: Table Saw Upgrades

#11

No replacement parts

MartinMJ

Your first paragraph has this statement:

"It has this goofy computerized system for raising and lowering the blade as well as angling it. If that ever goes out I am screwed as there is no replacement parts for that possibly 70's "High Tech"."

That means do not invest any more $ in this saw.

Re: Table Saw Upgrades

#12

Ellis Walentine

Won't work

Ellis Walentine

As Bruce noted, you need to have a WoodCentral profile to have the option of uploading direct from your computer. I can tell that Walleye is unregistered because his name is in black type. Registered members show up in hyperlink type. If you want to register, click the "My Profile" link above and follow the bread crumbs.

Another option for you that doesn't require registration is to upload your picture to Photobucket or other internet photo upload site and link to it from the Optional Image URL box.

My two cents is to look around for a decent used saw as others have suggested. It'll do whatever you want, it'll probably work better with an aftermarket fence, prob'ly have more power, and not be susceptable to sudden obsolescence.

Ellis Walentine, host

Re: Table Saw Upgrades

#13

Re: First,

John K Jordan

Oops, I forgot to check for that! I'll have to remember to check for the blue, underlined name.

JKJ

Re: Table Saw Upgrades

#14

Re: A well worded reply of sage advice

Walleye Tom

Thanks for all the responses.

Perhaps I should have given a bit more information. This was the first Table Saw I ever purchased when I was just a young Buckaroo. I think I was 14 at the time so it has a bit of sentimental value, but I like to take "old things" and retro them and make them more useful than original.

This is my 3rd actual Table Saw as I have one set up in my main 10,000 sq. ft shop, that is a 52" Delta Unisaw with an 8' x 6' Feed Table and Emergency Assembly Bench (on Casters). That has the 5 HP motor on it and cuts thru everything.

This saw would be just for my "Small Projects", mostly Clocks, and would be in a different shop which is right next to my house. You could call it a garage but it is 30' x 45'. It grew out of control while building it as I started plotting different places for things. It does have to share some room with whatever Boat or other projectI have in there working on as well. When it was all said and done, my Wife made me build her another garage JUST for Vehicles.

I have been watching local classifieds and Craigslist for about the last half year, the few times a saw comes up, it is gone before I get a chance to go look at it. So, I just figured this would be a fun project and get me my saw for this shop. I only do my Woodworking personally in the Winter. The Summer is left for other endeavors. If I do end up doing some Woodworking in the Summer, I like smaller tools that I can push outside and work with. I hate being indoors in the Summer. That's why this smaller saw would be so nice. Last night I did take the old stock fence off of it and tore it apart and cleaned it real nice and now it adjusts smooth across the table and actually sets solid, front and back the first time. How long that will last is anyone's guess, but I still will measure it against both ends of the saw blade to make sure there aren't any discrepancies.

This Pool Table is one of my larger Projects after it was all set up for the customer in his Entertainment room, but they are tedious and then once I get them built it is still best to hire a Pool Table Guy to come and install the Slate and Green on it as they have the tools and expertise needed for it. I just build it. I have been building a lot of things out of White Cedar Logs the last half dozen years and now I am personally wanting to move to Clocks.


img

Re: Table Saw Upgrades

#15

Re: Won't work

Walleye Tom

I'm not sure why it says I don't have a Woodcentral profile. I signed up and filled the profile segment out the other day.

Re: Table Saw Upgrades

#16

10,000 square foot shop.....

roger lance

that puts a different light on it alright.....

Re: Table Saw Upgrades

#17

This project makes no sense....

Bill Tindall, E.Tn.

"This saw would be just for my "Small Projects". I never heard of anyone needing to configure a table saw for "small projects" other than a blade change.

Install a 7 1/2" 40T Industrial quality combination blade on the Unisaw and you can nicely saw 1/8" thick material, or 1 5/8" thick material too. On the other hand, if you are into saw collecting by all means spend the money to put a 2 HP motor on this saw to saw clock parts. It will save the time of an occasional blade change on the Unisaw.

Re: Table Saw Upgrades

#18

Re: 10,000 square foot shop.....

Barry Irby

Yes indeed, a different light. I have a Craftsman radial arm saw I bought when I was 16. Had the motor rebuilt when I was about 18. Cut the tip nearly off my thumb with it in the early days. I still have it and use it often. I understand the sentimentality.

Nice pool table.

Re: Table Saw Upgrades

#19

Re: Table Saw Upgrades

Kevin

I have an old sear craftsman saw that I built a nice cabinet and put a nice T fence on it. I kept the one hp motor. That saw has worked great for me and I have had over 30 years using it. I figured if I needed to replace the saw, the table size will work for other saws as a replacement. I considered a larger motor but I make do the the 1 HP. I did set it up for 220V. The new cabinet saws are really great. If you have the money to spend, they are a great value if you use for a lifetime.

Re: Table Saw Upgrades

#20

Re: Won't work

William Duffield

"Walleye Tom" doesn't have a profile. When you filled out your profile, you spelled something differently, and the WoodCentral app can't match that name up with "Walleye Tom". It isn't good at guessing. In fact, unlike Google, it is abysmal at guessing.