Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Making chairs

Posts

Making chairs

#1

johannaj

Making chairs

johannaj

I have been taking a class in chair making at Santa Fe Community College. Dealing with all the angles is really a stretch for me. I have made more jigs in the past 3 months than in the past 10 years! Here are a few of them:

Jig for tenons and mortises - This jig uses wedges on the adjustable vertical face and the vertical back to make compound angles on tenons or mortises. If I were to do it over again, I'd use hard maple rails on the vertical adjustment instead of track. This jig was designed by Larry Buechley (see Buechley Woodworking .com) - he teaches router joinery at Santa Fe Community College.


Tenoning top - this top makes it easy to route the complete tenon (both ends). This one is set to make half-inch tenons using a 3/4 inch Porter Cable template bushing.


Mortising top - This uses the same 3/4 inch Porter Cable bushing


I'll take some pictures of the other jigs and put them in a separate post.

Re: Making chairs

#2

johannaj

Re: Making chairs - 3 more jigs

johannaj

Here is the mortising jig used on the front legs - I have used it on quite a few projects besides chairs. The sliding top portion is cut to exactly fit the base plate of one of my routers. It has two adjustable rails that must snugly fit the upright sides of the lower portion of the jig. The lower portion has a front upright that is fixed and a sliding back upright. The piece is loaded against the front upright with enough boards under it to raise it flush to the top edges of the front and back uprights. The back upright is moved up against the workpiece - there are three knobs under the jig that tighten the back upright once it is set in place. I use a clamp to pinch the sides tightly against the workpiece. Also, you can see there is a stop block fixed to the front upright. The two L-shaped pieces on the front are adjustable stops for the sliding top.



A tapering jig based on one by Steve Latta in Fine Woodworking


A small mortising jig with a fence that fits one of the curved back legs of the chair. The fence on the bottom has to be moved when the left leg is routed - it is currently set for the right back leg. That's why it says "Left" on one side!




Re: Making chairs

#3

johannaj

Re: Making chairs - 3 more jigs

johannaj

One more item - there is another small mortising jig to fit another curved area of the back legs.

Here is the mock-up in poplar (the goal is to make 6 dining chairs in ash) with all parts completed except the crest rail and the back splats. Today I plan to cut clamping blocks so I can clamp it and fit the crest rail.



Re: Making chairs

#4

johannaj

Re: Making chairs - some info

johannaj

The back legs are at a compound angle. This has the effect of increasing the splay of the top - and also has the effect of making it really difficult to fit!

The metal bit on the front view was there for the band clamp that I was using to hold it together when transporting it to and from school.

Re: Making chairs

#5

Re: Making chairs - some info

Fetcham

They are some really nicely made jigs, Joanna, and the chair looks great. What sort of back splat and crest rail are you planning?

Jim

Re: Making chairs

#6

johannaj

Re: Making chairs - some info

johannaj

The crest rail will have a cut out area like the one on the magazine rack below. It will sit about 2 inches below the tops of the back legs.


There will be three 1 1/4 inch back splats. They will have about the same curve as the back legs, but more exaggerated to fit the curve of a person's back. They will be bent laminates.

Re: Making chairs

#7

Re: Making chairs

Bruce, a MN Galoot

Nifty jigs and chair you've made. Are those jigs adaptable to other styles of chairs or are they only made for this one?

Re: Making chairs

#8

Thanks!

Tony-Memphis

Nice work and thansk for sharing. And how timely, I've been considering building 4 chairs for our breakfast room to replace the hodgepodge of chairs we have in there now. I've been studying Garret Hack's chair article in FWW. Fairly simple as chairs go.

Tony

Re: Making chairs

#9

Re: Making chairs

jesse cloud

Good looking chairs Johanna!

Are you going to do a slip seat with upholstery?

Re: Making chairs

#10

Ellis Walentine

Great post, Johanna

Ellis Walentine

Your jig efforts are excellent, and the chair design is going to be wonderful. Thanks for the documentation.

Ellis Walentine, Host

Re: Making chairs

#11

Re: Making chairs

Joanne in Point Pleasant, PA

Excellent! Thanks for sharing those pics. Kitchen table and chairs are on my list for my house. I made some ottomans for friends last year so I could teach myself how to upholster, so I'd be ready for making that part of the chairs. I think that was a lot easier than the wood part and making all kinds of jigs. Can't wait to see your finished chair.

Re: Making chairs

#12

johannaj

Re: Making chairs

johannaj

The large jigs for mortising, tenoning, and tapering are not specific even to chairs. The little jigs for mortising in a curved area are specific to the particular chair.

Re: Making chairs

#13

johannaj

Re: Thanks!

johannaj

While there are many chairs that have only 90 degree angles, they are not very comfortable. As soon as you tilt the back and slope the seat you introduce compound angles that are much more difficult to deal with. This chair is difficult because 1) the back legs have compound curves (although the outside of each back leg is plane), and 2) the back legs are "twisted" or rotated to increase the splay of the top of those legs.

Re: Making chairs

#14

johannaj

Re: Making chairs

johannaj

Yes, Jesse. I will soon be looking for appropriate upholstery fabric.

Re: Making chairs

#15

Re: Making chairs - some info

Fetcham

Sounds great, I like that cut out motif. The back slats sound very like those that I used in my own chair project, designed to fit the curve of the lumbar region. In my book a chair that isn't comfortable is a failure, however good it looks Here is a pic

I've made four of these - two with three slats and two with four. Interestingly from a comfort point of view the four slat versions are better because there isn't a slat directly on the line of the sitter's spine.

Jim


img

Re: Making chairs

#16

Re: Making chairs - some info

Fetcham

That didn't work, Maybe this will!

Jim


img

Re: Making chairs

#17

Upholstery Fabric

jesse cloud

Try Nob Hill Fabrics on Cutter St (parallels I-40 one block North) between Carlisle and San Mateo (easier if you come from San Mateo).

They have a good selection and lots of samples they can order from. We ordered from a sample and it arrived in less than a week.

The people are really nice and helpful.

Another source is NM Fabric and Foam on N 1st St.

Re: Making chairs

#18

johannaj

Re: Making chairs - some info

johannaj

That is a really cool chair! I'm planning on making 4 slats using bent lam and curving for lumbar support. I agree that if it's not comfortable it's not a good chair. I based my measurements on some chairs that were, indeed, very comfortable.

Did you slope the seat down a bit toward the back? I cannot tell from the picture.

Re: Making chairs

#19

johannaj

Re: Upholstery Fabric

johannaj

Thanks, Jessee - I'll check them out.

Re: Making chairs

#20

Re: Making chairs - some info

yetloh

Glad you like it. Yes, the seat slopes from front to back by about 2 degrees. S well padded seat makes this a bit less critical but 2 or 3 degrees seems about right. Look forwad to seeing the finished article.

Jim