Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

where can I get an aluminum fence with 3/4" T-slot

Posts

Re: where can I get an aluminum fence with 3/4" T-slot

#26

Why not use the bar as a fence

Dave Paine

Since the bar runs most of the length of the table and appears to be about the height you want for smaller fence, why not just use the bar without the aluminium extrusion.

If you need a fence, just use a piece of 3/4in plywood with holes recessed for the screws to mount. Do you need a slot to move the fence front to back?

Re: where can I get an aluminum fence with 3/4" T-slot

#27

Re: Why not use the bar as a fence

Adrian

The bar is about 3.5" tall, which is higher than I want. I want something more like 1.5-2 inches high so that I'm not cutting 1" material with 3.5" of blade exposed.

The reason I have for not just bolting on a piece of wood was the desire to keep easy interoperability with the stock fence extrusion---so that when I do want the 7" tall fence I can easily put it on. It may be that I'm putting too much emphasis on this. I could just tap M8-1.25 screw holes into a piece of wood and screw it on directly, which would certainly be simple.

Re: where can I get an aluminum fence with 3/4" T-slot

#28

How about mitre track *LINK*

Dave Paine

With your desire to slide on, how about routing a piece of mitre track into a piece of 1in think wood?

The present nut looks too deep, but I can easily machine a couple of custom nuts for you to work in the mitre track and the original fence.


https://www.woodcraft.com/products/woodriver-32-length-standard-3-4-miter-track

Re: where can I get an aluminum fence with 3/4" T-slot

#29

Re: How about mitre track

Adrian

I'm missing something with this idea. The miter track is just a 3/4" wide, 3/8" deep slot, so how would that help my fence hold on?

Re: where can I get an aluminum fence with 3/4" T-slot

#30

Re: How about mitre track

Dave Paine

These tracks are glued or screwed into a slot routed into the wood. Some are pre-drilled for the screws, but easy to drill any desired holes. I would epoxy into a routed slot rather than screw.

Re: where can I get an aluminum fence with 3/4" T-slot

#31

Did you mean T-track?

Adrian Mariano

I understand that you glue or screw track into a slot. But miter track gives you a smaller, aluminum lined, slot. There's no obvious way to mount something with miter track onto something else. The T-track one can buy is much smaller than the T that my existing setup has. So if I want to maintain compatibility with the existing setup, I think I'm better off building up a T by gluing aluminum strips over a slot cut in the wood. (This option is also cheaper.)

Re: where can I get an aluminum fence with 3/4" T-slot

#32

Miter track has lips too...

John in NM

But its bigger than T-track. Some miter guides and similar accessories have little washer like things screwed to the bottom of their guide bars so that they can't tip out of the miter slot. Not all machines have the extra slots cut in them for those washers (my table saw doesn't) so the parts are often removed and forgotten.

Anyway, you could make a wood accessory fence using either miter track or T-track epoxied into a slot and get pretty standard T-nuts to fit. Or just add the strips to the top of a slot as you describe. I think the T-track would be stronger, but for a fence that wouldn't really matter.

Re: where can I get an aluminum fence with 3/4" T-slot

#33

Re: Miter track has lips too...

Adrian

Sorry, I didn't notice that this miter track was T-shaped. It seems like the T-shaped ones are the exception.

But it's not compatible with the existing fence setup. It seems like if I'm going to abandon compatibility with the existing setup I may as well just do tapped holes in a piece of wood, since that's very simple. No hardware at all.

Re: where can I get an aluminum fence with 3/4" T-slot

#34

Jim DeLaney, Austintown, Ohio

Re: Why not use the bar as a fence

Jim DeLaney, Austintown, Ohio

How about a piece of 8/4 hardwood (maple?) a couple inches wide.

Rout or use a dado blade to put a 3/4" dado (groove) in it, then glue on a couple thin pieces to give you the 'T' slot.

Re: where can I get an aluminum fence with 3/4" T-slot

#35

Re: Why not use the bar as a fence

Adrian

That's basically what I'm thinking. The reason for gluing on aluminum instead of wood is that I can use 1/16" thick aluminum and it's easy to swap fence attachments, since it would be the same thickness as the fence extrusion. If I use wood, I'd probably want it 1/4" thick, so I'd have to back off the screws a bunch.