Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

A Survey of Sorts

Posts

Re: A Survey of Sorts

#26

Re: A Survey of Sorts

Brian Holcombe

My most memorable one was using a flush cut saw on the side of a box. It slipped and hit my finger. I've since worked to figure out every which way the blade will go if it moves through the wood faster than expected. :D

I've always had a shop, even as a young kid, and my father would give a basic overview on safety when I got a new tool. He bought me a small bandsaw as a kid and explained to me that I should always ask myself what would happen if the wood disappeared suddenly. Where would my hands go, etc.

He taught me never to lean into a tool because a slip can spell very bad news at that point. He also taught me to be aware of how to shut the tool down fast and get yourself out of the way.

He explained to me how to make and use push blocks, I have a push block for every stationary tool (lol....both of them), along with safety glasses and hearing protection hanging on each tool. I retract the tool bits and lower blade guards when not in use. The router table I unplug and the bandsaw remains locked out.

When I was in school I worked jobs as a machinist and also a welder/fabricator. My father mentioned to me, very seriously, that people always get injured when the pressure is on. He told me to think outside of the situation and refuse to put myself in harms way. He explained that as a welder/fabricator himself he would often refuse situations which were particularly dangerous.

The machinist I worked for was extremely cautious about the machines and what the people working for him were doing on the machines. I am always thankful that I had that experience working for someone who was as aware as he was. I cannot recall even one time where he was hurried into a situation, or hurried at all. He has a strong will to do what is right and refuse dangerous situations. He warned me that each and every tool had unique dangers and that industrial machinery was incredibly powerful and that being rushed into a bad decision could have life-long results (or life-ending results).

Working for him was helpful to me as I moved into other jobs that would make pressure-cooker situations for no real reason.

I remember refusing to weld a gas tank to the point of nearly being fired from one job. I told the people pressuring me that they were welcome to put their own hands and face at risk....oddly enough those willing to put my person at risk were not willing to risk their own lives. ;)

Re: A Survey of Sorts

#27

Re: A Survey of Sorts

jessecloud

Only serious injury I've had was a fall, with a running jigsaw falling a little ahead of me. I put out my hand to break the fall and went right into the saw. Messed up some tenons and bone. The bone grew back, but the tenons are still short where they were sewn back together. Lost about 20 degrees of movement in that finger.

My hand surgeon said a couple of interesting things. 1)Most fall injuries result in wounds to the dominant hand, which we instinctively use to break the fall. 2)When he mentioned he was interested in learning woodworking, his wife bought him a tablesaw for Christmas. He turned it on, thought a minute, and then took it back to the store. Of course, a hand injury would totally ruin a surgeon's career.

Re: A Survey of Sorts

#28

Re: A Survey of Sorts

Barry Irby

Career Ending....A friend of a friend is/was a dentist, somehow got his right hand into his chop saw and cut off all four fingers across the joint closest to his palm. In their excitement he and his wife forgot to take the fingers with them to the emergency room. He is no longer a dentist.

Re: A Survey of Sorts

#29

Re: jointing short piece

Larry Clinton At Frankfort, (Central) Indiana

I can't disagree with you, as far as I remember that is the only time I did try to run a short piece through. Obviously I didn't engage my brain prior to doing this. Had I used one of my push blocks the only damage would have been to the block. However as I stated I didn't think. All I was trying to do was expose a "new" surface so as to determine what the grain looked like. Had I not been quite tired and had done some thinking I would have used the stationary sander belt. It did end up a minor injury which I am thankful for and was a pretty cheap lesson I will remember for the rest of my life.

As my son (who is in his late 40's) was in the shop when it happened, he also learned a lesson and never uses the jointer, saw or router table without using a push blocks. Most of the time I have Gr-rippers available as well as some custom push blocks at each machine.

Re: A Survey of Sorts

#30

Re: Jointer Pusher

William Duffield

I will joint the edge of a 6" or wider board without a push block, but for everything else, I use this "boat".


A view of the business end, using replaceable loose tenons.


Extraction access ports, in case the push blocks get chewed up and there's not enough left to grab with a pair of pliers, I can drive them out with a pin pinch:


It snoozes here on the top of the jointer stand, so it is always at hand, and I'm not tempted to flatten a board without it.


Re: A Survey of Sorts

#31

Ooo, I like that!


Re: A Survey of Sorts

#32

Re: A Survey of Sorts

Marc in Mass

Left hand. I surmise if I was left handed it would be the right hand that is most often in harm's way.

Re: A Survey of Sorts

#33

Another left thumb incident.

Jim Dillon

While holding/repairing a birdhouse with my left hand, I managed to fire a pneumatic nail right through my left thumb. Hey, not an injury from a "real" woodworking machine, but the birdhouse was made from wood, so it kinda counts, right? Anyway, I've been (knock-on-wood) lucky so far. However, once while using my router table to rout a slender piece of wood, my holding finger slipped and touched the top of the spinning bit. Luckily the cutting edge did not go all the way to the top of the bit so I was lucky. But it sure gave me pause and new respect for spinning bits and using proper hold-downs for small pieces of wood. As an aside, I also treat the unassuming jointer with great respect and use push blocks similar to what William described, especially for thin stock. I like what JKJ said about thinking where ones hands would go if the wood was not there, and as another poster said, if it "feels" dangerous, it probably is. Jim (21 years of woodworking and still able to count to ten on my fingers :) )

Re: A Survey of Sorts

#34

Re: Another left thumb incident.

William Duffield

Whether it's a jointer, chopsaw or carving gouge, the question to always ask yourself before starting to cut is:

"Where is it going to go WHEN it slips?"


Re: A Survey of Sorts

#35

Re: A Survey of Sorts

Barry Irby

I can still count to ten on my fingers, but they have taken a beating over the 50 years I have been wood working. When I was about fifteen I touched the blade on my RAS with the thumb on my right hand. Nearly lost the last joint. The doctor wanted to amputate the remaining part, but I said NO. It healed better than he expected, but the nail lacks part of its bed. Since then there have been many nicks and cuts but none as serious as that. A couple of weeks ago I foolishly used my right hand to clamp a small piece to the fence of a miter saw, with the saw swung to the left. The blade shaved the callus off the side of the pointer finger. Did not draw blood, but what a surprise. I shut down the shop and left. So, both of mine have been beat up and I don't know which one is the winner or would that be the loser?

Re: A Survey of Sorts

#36

Joe Bradshaw

Re: A Survey of Sorts

Joe Bradshaw

I can count up to 9 1/2 on my fingers. In a moment of in-attention, I passed the end of my pointer finger on my left hand across the blade my TS/. I had a nice diagonal cut across the nail. I finally had to have the nail removed, since it was pointing in two different directions. I had to us a Dremel to trim one of the nails. My girlfriend said that I needed to get rid of that saw and get a Sawstop which I did. I sure miss my Unisaw.

Joe

Re: A Survey of Sorts

#37

Re: No preference

Ron Pemberton

I have been woodworking for over 55 years and have not drawn blood. I am now 74 and 5 months ago I was routing an edge with a 690 Porter Cable router. For some reason ???? the moter came loose from the base and fell to the floor. By reflex I reached for the motor.


Did not hit a joint or tendon. Can't hardly see the scar today. Lucky lucky

Re: A Survey of Sorts

#38

Re: jointer question

TomD

Square spindles are certainly no longer sold around here, but they are prized by those who like old machines. I suspect that the jointer Konrad Sauer that was a marvelous antique may have been so equipped, though he may have had a proper head made for it.

I was not however talking about an auto feed entrainment from a square cutter exclusively on a planer/jointer. Just the fact that if you fall into the cutter head, which is sorta what happens when you press down over the head, experience kickback, and feed yourself into the machine, that there is nothing to stop you from ending up like the cadaver being fed into the chipper in Fargo. It will just keep on cutting as long as you are pushing. In practice you won't loose an arm, but the injury is not likely to be a small nip either. A lot of woodworkers are older, not having great balance, and if they do not have a foot under their hands, and they are pressing down over the cutter, it will not be pretty if they loose the piece.

Shapers are terrifying, you are right there. However they are rare in most home shops. Powerful router tables are not and they can be tricky if not as likely to cause havoc.

Re: A Survey of Sorts

#39

Re: A Survey of Sorts

TomD

"Mark, they make some nice kevlar gloves that would protect your thumb."

I always seem to run amok with gloves. I see all these guys today working with those fancy gloves that cost 20-50 dollars. Most recently when I tried to use a pair last year, they caught in the drill press and would have ripped my hand off, except I don't use that powerful a motor. I know it is mostly just me. But a cut I can take, having a hand wrapped and twisted off, or a whole arm, not volunteering. That slow speed on a big press looks so safe, but it can wind you up like salt taffy.

Re: A Survey of Sorts

#40

Ellis Walentine

Re: jointer question

Ellis Walentine

Hi Bill,

To tell the truth, I can't recall what went wrong. It happened back in the 70s and my memory of those days has faded considerably. It wasn't a kickback. I seem to recall that it was a fairly narrow piece, not overly short. Maybe the piece somehow slid over at the end of the cut. I think it was at the end of a long day in the shop and my attention wasn't keen at that point.

Sorry I can't give you any takeaways on this.

Ellis

Re: A Survey of Sorts

#41

Re: My Table Saw Pusher Pusher

William Duffield

As I noted earlier, the push stick for the table saw must not only push the stock through the blade, but must be designed to hold the leading end down so it won't be lifted and thrown by the blade. This is it's basic configuration: It is modular. You can make the beam as short or as long as you like.


There are other design criteria I find important. If you are going to use it habitually, the handle (or tote) must be comfortable. This one is configured to increase the down force on the end of a long beam. You can make it more upright if you are pushing shorter stock with a shorter beam.


It must function on very narrow stock and also on very thin stock. For narrow stock, the beam and peg are sacrificial.


For thin stock, the height of the peg is adjustable.


All the parts are replaceable. You can turn the peg over, or hammer it down farther after you've chewed up the end of it. You don't have to knock it out to trim up the bottom with a band saw or dovetail saw. Don't try this at home, but I've even trimmed the end off a peg with my radial arm saw.


You can make the beam out of any piece of scrap, and you can punch holes for the peg and tote tenon in several at the same time and set the spares aside for later.

Quite a while ago, I made a batch of totes and put most of them away in my jig parts drawer for use later on other jigs and appliances. That's why the tote on my TS pusher and my jointer pusher and my TS leg taper jig all look similar.

You can find instructions and plans for making totes on Lee Valley's website. For example, here is the link to the Stanley #5 tote plans:

https://www.leevalley.com/us/html/16j4010k.pdf

For others, Google "lee valley stanley tote template"