Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Rockwell 11-280 32" Radial Drill Press

Posts

Re: Rockwell 11-280 32" Radial Drill Press

#26

Re: Stop nuts...

ChuckInND

Well I received the depth stop rod the other day and find out that the threads are uncommon. It is a 1/2" rod with 16 TPI. So now it's either bite the bullet on the stop nuts, or replace the rod so I can use common sized stop nuts. This is turning out to be a much bigger project then I realized. Yesterday I add a lower shelf to the steel stand in order to stiffen up the legs, and give me a place to store the larger table when it's not needed. It did the trick, it's rock solid now. Next will be to take the stand apart, sand it lightly, and repaint it.

Re: Rockwell 11-280 32" Radial Drill Press

#27

Re: Stop nuts...

John in NM

Is it a standard 60 degree thread profile or an acme like mine? You can get that size tap from oddball suppliers like Victor Machinery if it's a standard profile.

Re: Rockwell 11-280 32" Radial Drill Press

#28

Re: Stop nuts...

ChuckInND

John, I found one company, Hammerscale that sells depth stop nuts that are threaded for 1/2" by 16 National Special. They sell for about &40 for a set of two, plus shipping. I don't know much about thread pitches. I took the rod and measured out an inch and counted out the threads to be 16 per inch. Thank you for the heads up on the taps from Victor Machine. http://www.victornet.com/detail/TAST-1/2-16.html

Re: Rockwell 11-280 32" Radial Drill Press

#29

I bet the ones I made are in there....

John in NM

Don't remember the sizes offhand, but my drill press is a pretty common one - it was a Walker Turner model from right around when Rockwell took them over. Probably would have just bought some if I'd known :D - but then I'd have missed out on learning a thing or two making them.

Isn't it amazing what you can find on the internet?

Re: Rockwell 11-280 32" Radial Drill Press

#30

Re: I bet the ones I made are in there....

ChuckInND

Yep, the internet. I may have found a set of original Delta / Rockwell stop nuts on the internet.

Re: Rockwell 11-280 32" Radial Drill Press

#31

Re: Stop nuts...

Hank Knight

Go to MSC Industrial Supply (Www.mscdirect.com) and search for Knurled lock nuts. They have many sizes. i ordered a pair for my Walker Turner drill press from them 5 or 6 years ago.

Re: Rockwell 11-280 32" Radial Drill Press

#32

Re: Stop nuts...

ChuckInND

Hank, the problem is that the thread count on the stop rod is not common. A common 1/2" thread count is 13 TPI, the stop rod I have is 1/2" with 16 TPI. MSC from what I could see only carries common thread sizes for the knurled nuts that I'm looking for. I've looked all over and I did find someone that sells what I'm looking for, but the price for a pair plus the washer between, it would be more cost prohibitive for me to either find a different stop rod that has common threads and the nuts, or I could attempt to make one out of a bolt. As someone said, what are people doing with the stop nuts that there is a market for new ones ?

Re: Rockwell 11-280 32" Radial Drill Press

#33

Re: Stop nuts...

Hank Knight

Chuck,

There's a guy in Connecticut named Jeff Hoffman that specializes in rebuilding vintage Walker Turner machines. His business is Walker Turner Serviced Machinery, LLC. He helped me rebuild my early 1950s Walker Turner drill press. Is a really nice and knowledgeable guy and he has lots of parts of all descriptions, not limited to Walker Turner parts. Email him at: wtsmllc@juno.net and see if he can help you. I haven't corresponded with him in several years, so I don't know if that's still a good email address. I. Assume it is.

Good luck. Post pics of your machine.

Hank

Re: Rockwell 11-280 32" Radial Drill Press

#34

Re: Stop nuts...

ChuckInND

Hank, I threw Jeff an e:mail and it was returned as undeliverable.

Re: Rockwell 11-280 32" Radial Drill Press

#35

Re: Stop nuts...

Hank Knight

Chuck,

I'm down to my last suggestion. I did some online research and found that Jeff Hoffman's email address may have changed from dot.net to dot.com. Try:

wtsmllc@juno.com

If that doesn't work, all I can suggest is that you try to find Hoffman's phone number. His business, Walker Turner Serviced Machinery, LLC, is (was?) located in Coventry Connecticut.

Hank

Re: Rockwell 11-280 32" Radial Drill Press

#36

Re: Stop nuts 1/2" 13 TPI...

ChuckInND

Hank, I'm thinking that address may have worked. I did not get an almost immediate reply stating that it was undeliverable. So it must of went through, unless the mailer demon has weekends off, lol. Here is the place that I found that has what i'm looking for, but a bit pricey when I've seen used ones go for about $15 a pair plus shipping of course. http://hammerscale.com/HTML/Products/DrillPress/dp274.html

Re: Rockwell 11-280 32" Radial Drill Press

#37

Re: Stop nuts 1/2" 13 TPI...

Hank Knight

Wow, that is a bit pricey! If your email went through, Jeff will answer. I found him to be pretty responsive. If he has the replacement nuts, they will probably be cheaper than the ones you found online.

Re: Rockwell 11-280 32" Radial Drill Press

#38

Re: Pictures ?

ChuckInND

I guess that I forgot how to post pictures here, I tried Photobucket.

Re: Rockwell 11-280 32" Radial Drill Press

#39

Re: Pictures ?

John in NM

You need a profile and to be logged in to post them hosted here. There is a 100 kB size limit, so they usually need to be shrunk and the resolution lowered.

Using photobucket, you select the IMG address or whatever it is for the image.

There is a bunch of junk that shows up in that address when used here, I've not seen it on images posted on vbulletin forums. Its easy enough to preview the post and just delete everything that shows up and isn't the picture. I used to like photobucket - but they made it all very buggy and complex a few years ago - somehow for the ease of smart phone use, no doubt :D

Re: Rockwell 11-280 32" Radial Drill Press

#40

Re: Pictures

ChuckInND

I put some pictures of it in my website. They are at the bottom of the page. https://sites.google.com/site/deltacontractorstablesaw/

Re: Rockwell 11-280 32" Radial Drill Press

#41

Re: Pictures

John in NM

Looking good Chuck, I was expecting more of a basket case. That one cleaned up well.

Re: Rockwell 11-280 32" Radial Drill Press

#42

Re: Pictures

ChuckInND

Thanks John, as I said before, I have a couple days into cleaning the rust off of the milled surfaces of the table and base, plus the tubes in order for it to work smoothly. And not noticing that the depth stop assembly was missing so far has cost me about $40 for the collar and rod, and the way it looks it could cost me another $40 for just the stop nuts and washer. Luckily I had the new Dayton motor and the casters, other wise that would of been another $100 or more. The machinery stand I also have some time into and about $45, and I still have to paint it. It's real easy for things to start out as a labor of love and have a lot of thought and time put into it, and end as a money pit. It will be nice to have the drill press, but realistically it probably would of been better to just buy one new, but then again I can't help to think that it's got to be somewhat better then the new cheaply made imported machines.

Re: Rockwell 11-280 32" Radial Drill Press

#43

Not only...

Ron in Sterling, CT

will it probably be better than an imported one, but you saved it from going to a trash pile somewhere. Nice renovation.

Ron

Re: Rockwell 11-280 32" Radial Drill Press

#44

Re: Thankyou Ron


Re: Rockwell 11-280 32" Radial Drill Press

#45

Re: Stop nuts, or common thread stop rod

ChuckInND

Yesterday I decided to take a look at making a stop rod that has common threads. I picked up a 1/2" x 10" carriage bolt, and a couple 1/2" and 3/8" jam nuts. It will take some work to get it looking like the stock stop rod, but it looks doable. This is something that I'm going to try if I can't find a couple of reasonably priced stop nuts.

Re: Rockwell 11-280 32" Radial Drill Press

#46

What do the threads look like on the original?

John in NM

This:


or this:


If its the second one, you can probably make some fairly easily with a tap. If its the first you probably won't find a tap for it, acme taps are a bit unusual and fine pitch ones more so.

I gather that parts guy never got back to you?

Re: Rockwell 11-280 32" Radial Drill Press

#47

Re: What do the threads look like on the original?

ChuckInND

Hi John, the threads off the original equipment stop rod are American standard but are 1/2" 16 TPI thread, not the common 1/2" 13 TPI thread. For the stop nuts I could tap out two nuts with a tap that I believe you sent the link too for around $15 shipped I'm guessing. I also have two guys, Jeff included that think that they may have a couple of the 1/2" 16 TPI stop nuts, but they don't seem to be in any big hurry to find them, or give me a price on them. It would be nice to keep it all original if it doesn't get too expensive, But if I can make my own stop rod that has standard 1/2" 13 TPI threads I can purchase a quick adjusting Button Thread Nut, which would be kind of a nice upgrade for around $17 shipped I'm guessing. http://us.essentracomponents.com/en-US/psearch?productId=51248&categoryId=82067&facet=ads_f10502_ntk_cs%253A%25221%252F2-13%2522 I'm pretty sure that I can make the stop rod in a fashion that looks original to the drill press. I already started working on it this morning, and so far so good.

Re: Rockwell 11-280 32" Radial Drill Press

#48

Here's what I would try.... *LINK*

John in NM

Get a couple thumb nuts in a smaller size, like 7/16" or 3/8", drill them out and tap them for your desired pitch.

Going to be a little hard to hang on to for hand work, but you could easily make a two piece wood clamp block to hold the nut(s) securely.

Somewhere I used to have a couple blank ones. I thought of offering them to you, but I've no idea if I kept them or not or where I might have put them. A friend made them for my drill press before he realized that there was no tap available to thread them. I'll look around when I get home Saturday, but no promise I even still have them.


thumbnuts

Re: Rockwell 11-280 32" Radial Drill Press

#49

Re: Here's what I would try....

ChuckInND

John, the thumb nuts do look to be pretty affordable, I suppose that I could buy a 3/8 and tap it out for 1/2". But I've already started making a new depth stop rod that has common 1/2" threads. I've spent so much time looking for stop nuts and being disappointed with most of the outcome. I'm about wore out with it all and the easiest and most cost effective solution for me I think is the direction that I'm going with the new rod. Don't get me wrong, I really do appreciate all your efforts in trying to help me, and I thank you for it. I'll post a picture of how far that I've gotten with the depth stop rod this morning in my website.

Re: Rockwell 11-280 32" Radial Drill Press

#50

No problem Chuck....

John in NM

Glad you got something figured out :D