Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Demilune Table- legs

Posts

Demilune Table- legs

#1

Demilune Table- legs

Bill Tindall, E.Tn.

Deer hunting has slowed the progress but now I am at it again.

PIC 1



The skirt is done- veneered and the complicated joinery complete. More on the joinery later. There was a lot of fitting with a chisel.

PIC 2


The two front legs are attached with bridle joints and the legs taper on 3 sides. The back legs are convention M&T and they taper on 2 sides. The tapers were done with a Steve Latta jig. I am not fond of "wasting" time making jigs. In this case the wasted time was amply rewarded. Steve's jig is a quick, secure, and reliable means to getting the identical tapers required for these legs to look good.

PIC 3


I added one additional feature, a screw to secure the trailing end of the leg. After the leg is positioned the screw is extended which locks the leg in place at that end.

Re: Demilune Table- legs

#2

Re: Demilune Table- legs

roger lance

I have noticed more use of jigs by you of late..... :D

Please talk about the order of cut when using this jig.....especially when tapering three sides of a leg.....a very important consideration that might not be known by all.

Re: Demilune Table- legs

#3

Re: Demilune Table- legs

Joe in a Cleveland suburb

Great looking so far Bill and thanks for keeping your posts on its build going.

My little table isn't nearly as complicated or as nice looking as Bill's, but...

I don't remember exactly how I did the bridle joint for the front leg with my small half-round table,

but as I recall I made a jig to help hold the leg in place (I think I saw that in FWW), marked it out, then sawed it out.

Jig to help with layout


Layed out


Cut it out



Cleaned it out - should have cut more saw kerfs



Good to go



Seemed to work without much effort and is still holding strong...



Re: Demilune Table- legs

#4

order of cut?

Bill Tindall, E.Tn.

This thing didn't come with instructions. Was I supposed to cut in some order?

Re: Demilune Table- legs

#5

Re: order of cut?

roger lance

Instructions ?.....we're men and we wouldn't read no lousy instructions.....the last instructions some of us read were originally printed in 1740.

This is not a big deal.....but there is a little technique in using this type of tapering jig. I've only tapered this way where the two inside leg sides are tapered and the suggested technique is to have the legs mortised and to place the leg on the jig with one of the mortised sides down and the adjoining mortised side toward the saw blade for tapering. Once the first taper is cut, the leg is rotated so that the fresh taper is facing up and the second adjoining mortised side is now facing the saw blade. In this way there is always an uncut leg face down against the jig and also against the jig fence.

I would assume that there is a similar technique in making three tapers with the un tapered leg side being rotated down against the jig for the last or third taper. Perhaps someone else will speak to this.

What do you do to keep the two tapered and three tapered legs looking similar in size? Do you taper to produce the same size foot on these differently produced legs?

Re: Demilune Table- legs

#6

The issue....

Bill Tindall, E.Tn.



If an untapered leg face is down then the saw blade begins with a cut perpendicular to the length of the leg....and not if a tapered side is down (see picture). So, if possible do a cutting strategy where an untapered leg side is always down, which is not possible for a 3rd cut on a leg tapered 3 sides.

However, I ran a hand plane down the cut face to remove the faint saw blade marks from the rip blade. On the face where the saw cut began not perpendicular to the leg length I just planed the top of the taper to make it start the taper uniformly.

The bottom of the leg is the same 7/8 x 7/8 whether the leg is tapered 2 or 3 sides.

Re: Demilune Table- legs

#7

couldn't do it that way

Bill Tindall, E.Tn.

My screwy skirt arrangement with a drawer involved veneer on the skirt everywhere except between the legs where the drawer is located. Hence, my skirt has two radii, one between the legs where the drawer goes and a second slightly larger radii where the veneer is located (larger by thickness of homemade veneer). This small, but significant difference made the easy way of locating the joint that you illustrate not reliable.

Re: Demilune Table- legs

#8

Re: The issue....

mdclor

Bill, why not just tape one of the cut offs onto the side that was cut first?

Re: Demilune Table- legs

#9

Re: The issue....

Bill Tindall, E.Tn.

not worth the effort given that I am planing the leg anyway. but on a steeper taper taping the off cut back on would be a good idea.

Re: Demilune Table- legs

#10

Re: Demilune Table- legs

Terry Alexander

Do you know where we can get the plans for Steve Latta's jig?

Terry Alexander in West Texas

Re: Demilune Table- legs

#11

Re: Demilune Table- legs

William Duffield

I've never seen any plans for Steve Latta's; for sure it's not in FWW up through Issue # 237, which is the 2014 Tools and Shops. None of the dimensions are critical, as long as it fits together, doesn't have slop and isn't too tight where it slides against the fence clamp, and holds the legs you want to taper. The two sides should be parallel, but you achieve that when you clamp it against the fence and run it through the saw blade the first time.

I have some photos of Steve's, one of which is at the bottom of the post linked below. The other photos at the link are of my interpretation of his design.

http://www.woodcentral.com/woodworking/forum/messages.pl/pro/search/pmd/sread/srchid/22768d7eyXz2314XzBEP1449342472/spage/1/sanc/493469/sbid/1000/md/read/id/493469/sbj/latta-tapered-leg-jig/

BTW, Steve's also has a FHWS running through the stop block, but it's only just barely visible in one of the photos I have, and only if you know it is there. Look directly over the middle of the red toggle clamp handle. Only the point of the screw protrudes. The one on my sled is a lot easier to find. Too easy, in fact, thus the red arrows. :)


I'll see if I can find a couple more photos, if you can't figure it out from these photos and description.