Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Questions to DEWALT DWE7480 owners

Posts

Re: Questions to DEWALT DWE7480 owners

#26

Questioning the reason

Bill Tindall, E.Tn.

"Thin-kerf blades are less able to dissipate heat than standard plate blades."

Frist a disclaimer. All I know about blades is what various technical reps have told me at the IWF trade show and my local saw shop (that makes blades and other wood cutting devices). So, I am repeating what I think I remember that I have been told.

I believe the difference in thin kerf blades is that they can respond to heating by deforming more than thick plate blades. They are not going to radiate heat, or conduct to the air, any worse than a thicker blade. These are both surface process unaffected by thickness. For a given flux of heat into the blade by friction they will of course heat up faster than a more massive blade. But for a long session of ripping I believe they will equilibrate to the same temperature as a thicker blade. The difference is how they respond to this heating.

Heating will expand the plate which could lead to deforming if the plate is insufficiently stiff, or the stress is unrelieved. Note all the cutouts and squiggles in the most modern Freud thin kerf blade (and I suppose others as well). These alterations are there to mitigate the deformation from the blade heating up. Supposedly the red coating lessens heating as well by reducing friction. The coating will slow the loss of heat by conduction or radiation to the air.

I was in the market for a rip blade at the time of the last IWF show. I asked the Freud rep if there was any reason to buy the thin kerf bade. He claimed that the newest blade technology made them equivalent. I bought the standard kerf blade because I was uninterested in confirming his claim. And this situation may be why they continue to offer both plate thickness, one for skeptics and the thinner for the adventurous. Or maybe there is indeed a difference. In any case any discussion of thin kerf blades needs to date the experience for it seems that thin plate technology has recently advanced to where a thin kerf might be equivalent.

I have a Delta Unisaw with a 1.5 HP motor. Thousands of bdft of lumber have been across the saw. I have never longed for a larger motor. For higher volume 8/4 ripping of oak and maple, many years ago I had a standard kerf rip blade made for this saw. It simply has less teeth and it breezes through these thick woods. Sharp and number of teeth has as much or more affect on cutting resistance as the kerf width.

Another route to less deformation of the blade is to use smaller diameter blades. For nearly all my sawing I keep a 7 1/2" by 1/16" kerf blade on the saw. It is a modern high quality blade (CMT or equivalent) with stress relieving squiggles. I don't see any evidence of plate warping due to heating in any use of these blades in the past 10 years in lumber up to 6/4. It wasn't my revelation that this bade size has merit. I picked up us the idea from someone ripping high volume thin strips of wood.

Re: Questions to DEWALT DWE7480 owners

#27

Re: Questioning the reason

John in NM

The plate is simply less rigid and thus can more easily respond to stress of any source through deformation. Thin blades are great when they are sharp. I would look to a thicker one in the OP's application however - they are simply more stable and stability is required for precision. As I said before, I've had thin kerf blades cut every bit as good as a high dollar Forrest for a time - my gut feeling is that this time is not long enough to be worth any benefits they provide.

If you want to worry about the heat, look at conduction into the saw arbor rather than radiation an air convection. A thicker blade would have the edge there too, having a larger unit volume through which to conduct, but I doubt the difference is all that great between a thick blade and thin one.

Re: Questions to DEWALT DWE7480 owners

#28

That is a good idea....

John in NM

Using the low angle plane is about the best suggestion yet :D

Re: Questions to DEWALT DWE7480 owners

#29

Re: Questioning the reason

William Duffield

Some of the squiggles, the ones filled with rubber or some other vibration dampening compound, are also for quieting the blades. I prefer Freud blades because they are much quieter when cutting or spinning without load than other blades I've used, including Forrest. I don't know if they are enough quieter that I should be using them without ear protection, but I do. That's another good reason for not using Easy Off to clean them, because it attacks the dampening compound.

Re: Questions to DEWALT DWE7480 owners

#30

Ellis Walentine

Late to this discussion

Ellis Walentine

Sorry for the terminology. "Dissipate" has to do with radiating the heat. What I was referring to is that the thin-kerf plate expands more quickly than a thicker, standard saw plate, and also more quickly than the standard thickness portion of its own plate. Under some strenuous conditions, it can't dissipate the heat fast enough to cool it to a temperature that doesn't deform. Also, it is my guess that this dual-thickness situation means the edge can deform more radically, and quicker, because the heat hasn't penetrated and expanded the thicker part of the plate yet. That has been my firsthand experience, whether I perceived it correctly.

I do believe that a sharp, thin kerf blade can make a noticeable difference on a lower powered saw. I have owned two Unisaws and a PM68, and the only regular problem I had with my saws being underpowered for a task was with my first, 1 1/2hp, Unisaw, when I was ripping domestic lumber that was around 2" thick. I actually stalled the motor on many occasions and finally decided to trade up to a 3hp saw. It's very unnerving to be standing there holding a plank as the saw grinds to a humming halt. Not with all species, not at all times, but often enough to convince me. I grew up with a 3/4hp Sears tablesaw, so I had plenty of experience with low powered saw strategy.

Anyhow, any blade will warp if it gets too warm. I just think thin-kerf blades are more susceptible.

Ellis