Like other articles I've read on that site, this one is not accurate. I'd like to see some references to back up his claim that the 32mm system was developed to use
"a few specialized hand held machines and special relatively small jigs".
That's the hobbyist approach to building cabinets with the 32mm system, and the hand-held stuff and jigs came about long after the big machinery was developed. In real life, the 32mm system is all about production to crank out millions of cabinets as quickly as possible. That wasn't accomplished with little tools, it was accomplished with big ones; sliding table saws and beam saws, line boring machines, automatic edge banders and eventually CNC, in shops big enough to house all that equipment. The authors notion of
"No big factory, filled with large capital investment tools and machines, no big centralized warehouses, no big trucks needed to transport the goods to customers - or distributors - required. A very efficient, cost effective way to meet one of the challenges Europe faced at the end of the war, and the next 10 plus years."
is nonsense. He may have good intentions, but he should do his research. Without the factory and the equipment, there isn't much of an advantage to using the 32mm system for building cabinets.
And we still don't know why Baltic Birch plywood comes in 5 x 5 sheets. I suspect the reason is due to the fact that this material originally came from areas in the Eastern bloc during the cold war.
The commercial yards I mostly buy from have covered sheds for dimensional lumber but keep sheet goods, moldings, and better lumber indoors, perhaps due to the high humidity here. An employee or two always goes out with you to load unless you decline the help. They bring indoor materials to your trailer/truck. So easy and the quality is better than the HD/Lowes. I usually only shop at the big boxes for a few items since they are closer to me.
I accidentally found out once how to get instant help at HD - simply drop a 2x12 loudly on the floor and limp to the counter if no one shows up instantly. You will be swarmed with managers and helpers who will sort and load, ask if you need first aid, offer a chair and a refreshment while you watch, and appologize profusely in hopes you won't sue. This may not work so well in the work gloves isle.
The question that has yet to answered is; Did the standardization of cabinet dimensions if any drive the size of the baltic birch plywood, OR did the 5x5 more correctly 1500mm by 1500 mm happen for manufacturing ease and somewhat standard dimensions happened to fit. Sort of a which came first chicken or the egg.
Furthermore that may work for the thicker pieces such as 18 or 19 mm that would be natural for the major parts of the cabinet lower and upper boxes. But the dimensions are next to useless for things like 12mm parts of the drawer boxes. Oddly the 6mm thickness may still benefit as drawer bottoms.
Shrug. Chicken and egg debates are profoundly dull IMHO. I was just agreeing that the writing style on that site seemed a bit arcane to me.
I actually use the 12mm for cabinet carcasses, with a face frame on it. Makes for a more manageable box. Only time I had some 19mm it wasn't flat enough to be good for much.
Went to HD for some lumber. Picked through the stack and got the ones I wanted. Decided to bring the truck into the loading bay. Wouldn't start. First of many times. Its turning into a saga. Had it hauled in twice and of course it starts at the dealership. They can't analyze what its doing if it won't do it for them. While I was waiting (maybe fifteen minutes) for a friend to come give me a hand, HD restocked my carefully selected lumber. I was furious. Made them get the exact same pieces out and put them into my friends truck. Could not believe they were faster at putting stuff back into inventory than they are at getting it out.
It's the BS flag. I don't think it's possible to write about woodworking as a hobby without an understanding of woodworking as a business/trade. Well, it is possible but it leads to a lot of nonsense presented to an unsuspecting audience as fact. One of the tricks writers use is an "authoritative voice". That gets lost if you say "this is my guess, this is my opinion, this is something I'm making up but it sounds good." If all the audience knows is what they've read from other hobbyists, and they haven't read the old stuff, it's an easy sell. It isn't good from a technical or historical standpoint, but who cares if it sells books or magazines or drives traffic to the web site.
Baltic Birch plywood first appeared in the US in the 1970s (at least that's the first time I saw it. It's called "Baltic" because it came from the Baltic States of the old Soviet Union; Latvia, Lithuania and Estonia. The original appeal of it was the numerous plies, making a stiffer and more stable material. When it was first imported, the supply was hit or miss. Sometimes it would be available in certain grades and sometimes in others, sometimes not at all for a few months. I have no idea why it is made in 60" x 60" sheets. (They might actually be 1524 or 1525mm) I haven't measured one in a long time but they are at least 60", bigger than the 1500mm that has appeared from somewhere in this discussion.
My guess is that the odd size has something to do with the origin. Maybe that was as large a press as the Estonians were able to make. Maybe the Soviets had a surplus of steel that size and the Latvians used what they had available. Maybe there is a tradition in Lithuania of cutting logs in 5' increments. All of those maybes are things I just made up, but the production of material in that size sheet seems to be a local thing that hasn't caught on elsewhere. As Jesper said, most sheet goods in Europe are close in size to our standard 4' x 8' sheets.
To suggest that there is a link between this odd-size material and the 32mm cabinetmaking system is just silly. Most of the material in manufactured cabinets is not Baltic Birch plywood, it's particle board or MDF with a melamine surface, and as mentioned earlier that material comes in sizes familiar to us. Those materials are available is 4' and 5' widths and lengths of 8', 10, and 12'. To optimize the construction based on the size of the raw material would mean that every cabinet would need to be made from the same width parts, every saw would have the same loss to the kerf of the blade, and that no one would ever start cutting by squaring off the sheet to clean up the factory edge. The 32mm spacing refers to the distance between the bits in the original boring machines. Dowels and hardware plug into those holes, but the distance between the construction holes and the edge of the part can vary.
I did some research on the 32mm system when I was writing "The Complete Kitchen Cabinetmaker", but couldn't find a specific date or name pinpointing the origin. I'm not curious enough about it to dig deeper. My best guess is that it was a collaborative effort between German manufacturers after World War II. Almost all of the manufacturers of the machinery and hardware are German companies. My guess about it being a joint effort is based on my reasoning that if one guy, or one company came up with it independently, they would be bragging about it somewhere.
The shop where I was an apprentice in the 1970s had all the equipment, but no one ever referred to "the 32mm system". We were more of a custom shop than a production shop, and the guys who were trained in Europe may have known about it. As I recall, the hinges began to appear in the early to mid 1980s. The Germans likely were using it before then, maybe the 1950s or 1960s as they rebuilt housing after the war.
If you buy into the entire "system" it's a pretty efficient way to spank out basic cabinet boxes. If you skip parts of it, you lose the efficiency. I've been in shops where all the boxes were drilled for dowels on a multiple spindle machine and then the guy at the bench had to dip each dowel in glue and tap it in with a hammer. Not an efficient way to do it, but the owner of the shop nearly went broke buying the Altendorf saw, edgebander and boring machine and didn't have the $$ for the gun and feeder to shoot the dowels in.
Standard sizes for kitchen cabinets seem to also be a post WWII development. At the turn of the 20th century things like stoves and refrigerators were brand new, and weren't "built in". I've only researched period kitchen design up to about World War I. There may have been moves toward standardization in the 1920s, but hardly anybody built anything between 1929 and WWII. After the war lots of houses were being build and appliances were coming out of factories. The standard sizes are based on what an average person can reach, but they also exist so that the appliances and cabinets play nice with each other. Probably the biggest driver of standard counter heights (this is my guess and my opinion) is the widespread adoption of the dishwasher that fits under the counter. That's usually where someone who thinks they want an odd counter height changes their mind. What do you do about the dishwasher?
I've been using the 32mm system since the early 80
Keith Newton
The 32mm standardization came about, or was developed around that being the minimum distance that they could space the gears, bearings and collets for line drilling bars, with every other one being right or left hand rotation.
That has nothing to do with sheet good size. As far as yield, I'm fairly certain there is less waste cutting parts from longer stock, than from short. Whenever I have a lot of parts to cut, I always try to get my longest parts first, leaving the shorter lengths to come from the scraps off the longer. So starting with 5' material never has worked out very well for any of my carcass parts. I will however use it for drawer parts though, since they are all short parts anyway.
Wow, I love reading about the history here. I hope you write "The Unabridged History of Working with Wood" some day. When you do, don't forget woodturning. :-)
I could lose myself in your web site for hours although I rarely build furniture or cabinets. Now I want to get the "Great Book of ... Craftsman Furniture" and "Teaching Integrity" for armchair reading.
And with an extensive background in 3DStudio Max and a Sketchup dabbler, I also found your 3d focus interesting. Thank you for including your website link.
JKJ
PS. Your comment on the Authoritative Voice is perceptive and well stated. Some other forums I occasionally read trigger my BS filter so often they could be accurately renamed "Nonsense as Fact."
Bill, there are no real standards for framing, as the most common construction method is brick structures. My 1928 house has a double brick wall construction with a hollow between the two layers of brick for insulation. Originally just empty, but now filled with blown-in Roxul fibers. The outside walls end up being 16" thick.
The modern construction method is a combination of breeze blocks inside with brick on the outside.
Interior wall construction is anything from wood frame in a skimpier size than common i USA to breeze blocks.
"Sorry, I am reverting to UK English - hollow core ligth weigt concrete building blocks."
If I recall it right, they're known as cinder blocks in the US, some being hollow with two voids, and others, thinner by about half, being solid throughout. I think I'd struggle to describe either type as being particularly lightweight, although I'll grant the ones with the voids are much lighter than they might be if they were solid concrete throughout, ha, ha. Slainte.