Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

plywood rant

Posts

plywood rant

#1

plywood rant

Paul Blackwell

I went to a Big Box store (Lowes, in particular) looking for some 3/4 " plywood for a poker table I'm working on. Oak plywood at about $50 for what I thought would be a 4' x8' size. Imagine my surprise to find the actual size listed as 3.978 x 7.978, a thirty second of an inch less in width and length. Pine plywood was listed as 3.875 x 7.875 or 1/8 of and inch smaller. When did this happen? Also, 3/4 inch Walnut plywood is about $100. Given the paper thin plys, does anyone think it's worth $50 more per sheet just because it's walnut instead of oak? Big business continues to rip us off whenever possible.

Re: plywood rant

#2

A more metered plywood rant

BrianMonumentCO

I often find it necessary to trim off up to 1/4 inch sometimes even more because the big box stores HD in my case don't care for the plywood that well so it gets damaged.

So I don't really care about it being a 1/32 inch shy as I normally get rid of 1/4 inch.

On the other hand you could buy baltic birch but that comes in something near 5 by 5 foot sizes.

I am sure it is something more like 1.5 meters by 1.5 meters or something like that.

And if you insisted on Walnut you could buy veneer and apply it yourself.

IIRC the baltic birch plywood comes in METRIC dimensions.

So it is not one inch it is 25 mm (I don't actually recall seeing this thickness.

It is not 1/2 inch it would be 12 mm.

And 1/4 inch would be 6 mm.

Re: plywood rant

#3

Re: plywood rant

George Koch

Paul, are you sure the decimals are correct? I figure that 3.978 feet is under 47 3/4", 7.978 feet is under95 3/4" , 3.875' is 46 1/2" , and 7.875' is 94 1/2".

Either way though, I agree with you. Its a rip off. No pun intended!

Re: plywood rant

#4

Re: plywood rant

Richard McComas

Most the plywood I buy is 48 and 1half inches wide and 97 and 1/2 inches long.

Of course I don't to HD for plywood. I know better than that.

Re: plywood rant

#5

Re: plywood rant

fredhargis

I've been using Columbia Forest Products plywood the last few years, and like Richard has, it measures an extra 1/2" on each dimension. Very high quality as well, and runs only a couple of bucks more per sheet than the box stores at my supplier.

Re: plywood rant

#6

Re: plywood rant *LINK*

mdclor

Hey, Paul, I am reading a book by Bob Lang about making kitchen cabinets. He suggests that ply isn't the best product for making cabinets and favors higher grade particle board with a hardwood veneer or even hardwood veneer covered MDF for really high end work. See pages 71-75 of Kitchen Cabinetmaker. That certainly challenged my preconceived notions.

Anyhow, it you choose to go this route, you might be able to find what you want at Pittsford Lumber.


Kitchen Cabinetmaker

Re: plywood rant

#7

Re: plywood rant

Dick Coers

MDF? Oh lord I hate that stuff? That would be the heaviest way to build cabinets for sure!

Re: plywood rant

#8

Re: plywood rant

Barry Irby

You can buy MDF at HD that is 49" by 97". The explanation I got was that the edges are "tender" and tend to get beat up, so they give a little to rip off and clean up the edge.

I'm with Dick, I hate the stuff. Way too heavy and dust on steroids.

And, if it is not exceptionally water proof it falls apart readily if exposed to water. It will puff up in a mater of minutes. I sure hope the guy who wrote that book has a source for excellent material. I would be ashamed of cabinets built of the crap locally available.

Sheathing grade plywood has been an 1/8" undersized for years. Says right on it, "sized for spacing 1/8" at sides and ends".

I agree that the thickness drives me nuts. I posted about that a couple of weeks ago. I really wish they woudl pick a number and stick to it.

Some of the face veneers are so thin they have to put a backer veneer under it to keep the substraight from showing through. Something like common maple under tiger maple. Better not try to sand it.

Re: plywood rant

#9

Re: plywood rant

Larry

I also use Columbia Forest Products that I get from my wholesale supplier, Will not use ply from Home Depot. The only thing I don't like is the the face veneer is thinner then a few years ago.

Re: plywood rant

#10

Re: A more metered plywood rant

Jesse Cloud

A few years ago, Baltic Birch 3/4 in a commercial yard was 19mm, then 18mm, last week I bought some that was 17.5 (excuse me 17,5) mm. Very slightly under 60 inches square.

Re: plywood rant

#11

Re: A more metered plywood rant

BrianMonumentCO

1.5 meters works out to be 59.0055 inches.

18 mm is .709 inch

19mm is .748 inch almost 3/4 inch.

17.5 is .689 how bizarre.

Welcome to the wonderful world of metric wood sizes.

Re: plywood rant

#12

The only bizarre thing

Henry Higginbotham

. . . is that anyone would expect measurements in one logical system to convert to whole numbers in another largely illogical system.

Re: plywood rant

#13

More amusement about metric plywood dims

BrianMonumentCO

Why a manufacturer would make a product for another market than its own and wind up with dimensions are not even close to those used in that area.

For example 1 inch at 25mm, 1/2 inch at 12mm or 13 mm, 1/4 at 6mm.

But why have 3/4 be so far out.

In the USA that 3/4 is a standard building dimension or at least to be.

In terms of thickness why would they not make a 25mm, 10mm, 15mm etc.

I do find that the 5 ft by 5ft dimension to be the most troubling.

It isn't a standard size in USA systems nor is it a key metric size.

I might have expected 1meter by 1 meter or 1meter by 2 meters.

But 1.5 meter by 1.5 meter is just plain odd.

Re: plywood rant

#14

Jesper, Denmark

Re: Weird.......

Jesper, Denmark

Standard plywood size here is 1220 x 2440 mm, pretty accurately 4 x 8 feet. Same goes for drywall. Common thicknesses are 6, 12 and 19 mm.

Quite obviously a conversion from old US dimensions. A bit strange, as buildings do not use 16" and 24" centers as in the USA.

Re: plywood rant

#15

Bill Blasic

Re: Weird.......

Bill Blasic

Jesper what dimensions are used there for framing?

Re: plywood rant

#16

On hauling sheet goods and a Menard's Rant

Grant in Iowa

My Chevrolet truck, along with all of the full sized trucks, readily receives 4' x 8' sheet stock. If I would have bought the long bed version, it would even accept it with the tailgate up. It even has enough overkill to easily receive MDF with its extra inch.

Long ago I had a '78 El Camino, which would not accept MDF, but would accept normal ply (if memory serves). The factory air shocks meant it could be readily overloaded without looking like it was.

So I wonder if a similar vehicle exists wherever Baltic Birch is the norm.

I used to have an S-10 blazer when I was younger and was pleasantly surprised to learn that a 4x8 sheet of plywood would fit inside diagonally with the tailgate down. The plywood would stop neatly at the tailgate almost like someone planned it that way.

I often wonder how the world would look if the average human was -say 2 or 3' tall. Everything man made would be smaller, except strawberries would seem huge. I'd like that I think. At least until it was time to clean up the dog doo.

Now, on to Menards. Some person who has clearly neither owned a pickup nor ever moved much plywood alone has engineered the plywood aisle at Menard's, probably with the help of an injury lawyer.

So you go to the plywood aisle, and it is filled with A-frame carts. It seems all of the ones that should really be over by the trim, conduit, PVC pipe, etc. have been rounded up by an employee who has been told it is to be so. Never mind that from an ergonomic aspect, the A-frame cart is about impossible to load plywood in to, and even with help it is more work than it need be.

My approach is to go off in search of the elusive flat top cart, push it up to the plywood aisle and move all of the a-frame carts out of my way. Then I can pull out the sheets I need directly on to the flat top cart. Then I can push the flat top cart out to my truck and slide the plywood directly in to the bed. Never had to lift them entirely, never had to rotate, flip, turn, etc. I can even skip the damaged top sheet or two by sliding two out, pushing the top one back, wash rinse repeat. Works great, no need to find a staff member to help.

When told the carts are all wrong for the application, the manager said it is downward directed from corporate for safety of guests. It seems someone was injured by a plywood corner at some point, so the A-frame carts are put "in your face" in the plywood aisle. I asked him the rhetorical question: "How many guests have injured themselves picking up plywood, rotating it, placing it in to an a-frame cart, then repeating the process at their truck?" No answer as expected.

To the positive, if you have a contractors license (easy to get here in Iowa), you can get a "contractors card" allowing you to park in the lumber yard when you arrive. Right near the automatic doors where the plywood and contractors desk is. Saves steps, until you realize you still need to go to the register to check out. At least you don't need to push the cart back and forth.

Ok, I feel better now. Thanks for listening.

Regards,

Grant in Iowa

Re: plywood rant

#17

Re: On hauling sheet goods and a Menard's Rant

Dick Coers

I suspect someone pushed their plywood right off the flat cart and slid it into a bystander. I've had a couple sheets of OSB slide around pretty badly on them, but still prefer the flat cart. I just bought a Ford Transit Connect cargo van. 48.5" between the wheel wells. 72" floor space with the doors closed. I brought home a single sheet of OSB by resting it on the head rests, and closed the back doors. The sheet arced and was above my head. That thing has crazy good head clearance.

Re: plywood rant

#18

The Home Depot in Safford, AZ....

John in NM

Has all the sheet goods and lumber in a covered, drive through area. Drive in and load right into the truck. If I remember correctly you can pay at the gate too. Its the only one I've seen like that, it must make too much sense for wide application! :D

Re: plywood rant

#19

Why "5x5" - the 32 mm System

charlie belden

To answer the question "Why "5x5"?"'

Go to

www.woodworkinghistory.com

In the left "frame"

Click on "chapter 7"

Scroll down to "Conditions in Europe ..."

This site is a wealth of information, well worth spending some time exploring.

Re: plywood rant

#20

Re: Why "5x5" - the 32 mm System

BrianMonumentCO

I must be very dense today.

But how does anything in that article except the phrase ""workshop space' severely limited" imply/suggest or even hint at 5 foot by 5foot )Or 1500mm x 1500mm.

Re: plywood rant

#21

Re: Why "5x5" - the 32 mm System

charlie belden

Had you scrolled down to the section "conditions in Europe" and the next section on the 32 mm Syste, the reason for "5x5" sheet goods might be explainable. The sheet size optimized for the 32 mm system comes out to "5x5" - most usable pieces with the least amount of waste per sheet.

Google "32 mm System"

Re: plywood rant

#22

Re: Why "5x5" - the 32 mm System

BrianMonumentCO

I did. But it didn't show me how the 32mm system optimized to 1500 x1500mm

I have always suspected that the 1500 x 1500 was a first available size made by a factory.

Yet if cabinet dimensions were standardized under the 32mm system then I would expect to find them listed somewhere and a sample layout would prove or disprove either theory.

Re: plywood rant

#23

Re: The Home Depot in Safford, AZ....

Barry Irby

That's funny. Lowe's has moved three times in the last thirty years, maybe a total distance of a mile. First they had an outdoor yard with the material in the weather. Then they had giant steel sheds open on one side that you could drive to and load the stuff, and check out at the gate. Now they have it all indoors. Sounds like they had what you are talking about and did away with it. I live a quarter mile through the woods to where the store with the sheds was and I could hear the speaker system all day. (Not happy).

The carts both Lowe's and HD use baffle me. They are low but have four "hoops" of pipe creating three "slots". The middle two are taller. You have to heave the plywood up onto it edge, and over into the slot. Difficult by yourself. Looks like an arm breaker to me. I really can figure out how someone has not been hurt. And, If you ask for help they look at you like there is something wrong with you. I always try for the flat top carts. Easy to load and unload.

Re: plywood rant

#24

Re: The Home Depot in Safford, AZ....

John in NM

There was a place in Tucson like that, with big half open sheds. Weather was a problem. That seems more of a commercial yard model where units are usually covered and though they sell partial units, the volume is such that material moves pretty quickly.

This HD yard is completely covered (and presumably ventilated), and about the same size as the indoor equivalent. They have less storage area due to the isles being wide enough for pickups, but it seems to work well.

Re: plywood rant

#25

Re: Why "5x5" - the 32 mm System

John in NM

I didn't find it terribly clear either, but I attributed that to being tired after a long day at work, so kinda dull in the synapse department. I may go try again if I have time before going in today.

I did always like 5x5 sheets for cabinets. If one is doing 3' tall, 2' deep boxes, it's a pretty efficient size sheet. One foot scrap pieces can be used for uppers.