Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Lag screw lubricant

Posts

Re: Lag screw lubricant

#26

Clint Searl

Re: Lag screw lubricant

Clint Searl

This discussion is almost as enlightening and entertaining as the Kato vs. Kawai one, but I'm still waiting for the issue of molecular weight to be introduced.

Re: Lag screw lubricant

#27

True...

John in NM

If one only rarely drives lag screws, or 3" construction screws, then an impact driver is probably an unnecessary luxury. Once you have one, driving a phillips head any other way rarely makes sense. Lots of unnecessary luxuries improve our work and lives in spite of being luxuries.

After 10 years building 4 structures, I've driven a few hundred pounds with one and even went so far as to use it for hanging drywall. I still use regular hand drivers too when they are the right tool, but mostly the impact. If it quit tomorrow I would go buy another without pause, even though the bulk of our building is done.

Re: Lag screw lubricant

#28

Re: Are we talking about the same screw!

Barry Irby

One more thing....If you drive a bigger lag screw with an impact driver and want to give it a final turn with a wrench or socket, you should do it immediately, as in NOW. Once they sit for a while the surrounding wood grabs on and they can be very difficult to turn.

And yes its a luxury tool. But not so much after you have one. Its a tool you did not know how useful it would be. It like the difference between hand driving screw and driving them with a drill. Its hard to describe how much better and impact driver is than a drill or screw driver. I am hanging doors (house doors) and driving the hinge screws with a little 12 volt driver. Practically fist sized, no cord to drag around, and it drives all three hinge screws quicker than one by hand. The French doors were sagging. Drove two three inch deck screws into the top hinges. Lifted the doors and pulled them back. Work fine now. Screws I could not remove from my planer by hand came out so easily with the impact drive I thought I had made a mistake. Its a beautiful thing.

The OP may not be able to justify one for 4 or 8 lags, but Christmas is coming.

Re: Lag screw lubricant

#29

This thread has run off the rails

Bill Tindall, E.Tn.

It began with a need to fasten a machine down, in who knows what kind of wood, with a few 3/8" lags. Guaranteed to work, no risk, solution is to drill a pilot hole, lube the screw if into hardwood and employ a ratchet wrench. No risk of the lag not penetrating, splitting the wood or shearing the lag.

The virtues of an impact driver for conventional screws is another world of application. On a personal note I find an impact driver invaluable for erecting deer stands with long screws into hickory trees. But my occasional use of the tool has not enabled me to achieve fine control of screw depth. For precise screwing I use a screw driver or ordinary drill with speed control.

Re: Lag screw lubricant

#30

Lube molecular weight distribution

Bill Tindall, E.Tn.

The problem with Paraffin wax is that the molecular weight distribution of paraffin wax renders it too brittle to stick to the lag well. Toilet bowl wax, or the band saw wax sticks, are more ideal and sticky, but not too sticky. Faced with lagging a machine down to some beam I might just opt for a lower molecular weight paraffin like motor oil, synthetic or regular.

Can anyone comment on the recommended torque for lag screws. Surely there is a standard. And BTW, I prefer an air driven impact wrench for lug nuts. :)

Re: Lag screw lubricant

#31

415, 6.52 g/cm3 at 25° C   


Re: Lag screw lubricant

#32

Impact driver fan club

John K Jordan

>Its a tool you did not know how useful it would be.

Since this is the impact driver fan club, I have to mention how useful one is drilling holes as well as driving screws. When drilling holes for wiring through studs or double plates forget spade bits in an electric drill. With an impact driver, the aggressive Speedbor bits I buy from Lowes (Irwin) will bore a 3/4 or 1" hole through double or triple 2x lumber in a few seconds. You have to be ready since it will be an inch into the wood in a heartbeat.

These bits have a tapered screw tip which pulls so well drilling is usually effortless - very appreciated when working overhead. And big spiral flutes to pull out the chips. I have used these with a cordless drill but with an impact driver there is NO comparison.

When building my shop I also used these bits to bore through 6x6 PT posts, both straight through (from both sides to meet in the middle) and to meet at about 90-deg to turn a corner. If I accidentally drill into a nail or screw they are easily sharpened.

I use a Hitachi and a Dewalt driver. Batter boards, bracing, concrete forms, beams, studs, roofing, panels, wiring - ain't no way I'd want to start on my next building without one. Or two.

JKJ

Re: Lag screw lubricant

#33

Re: This thread has run off the rails

John K Jordan

>On a personal note I find an impact driver invaluable for

>erecting deer stands with long screws into hickory trees.

Someone in the future with a sawmill will curse your offspring!

With my band mill I am careful about yard trees and the first 4' or so on a any tree that might have come from a farm with fencing. Never, until now, have I worried about ruining a blade when sawing a log from high in a tree from deep in the woods. Ack.

This would not work for your tree stand, but when fastening things like no trespassing signs to trees I keep a supply of aluminum roofing nails, and believe it or not, some aluminum lag screws I stumbled across years ago.

JKJ

Re: Lag screw lubricant

#34

As Long As You're Not Finishing

Mark Mandell - Gone Round In New Jersey

a quick wipe with the Johnson's rag is quite enough to put a 3/8" lag down a 1/4" pre-bore

Re: Lag screw lubricant

#35

Re: Worlds best screw lube

William Duffield

I couldn't find your stick wax on the Internet. Then I found out that johnson lhad sold that business to Castrol. So, if anyone is looking for it, search for Castrol #140 Stick Wax. It's not cheap.

http://www.amazon.com/Castrol-Stick-Wax-Metal-Working-Lubricant/dp/B00H9P0T0U/ref=sr_1_2?ie=UTF8&qid=1441300710&sr=8-2&keywords=johnson%27s+stick+wax

Amazon also offers a few competing products.

Re: Lag screw lubricant

#36

I'm surprised....

John in NM

The Makita version I have is great for fine depth control - that's why I like using it for hanging drywall. Something to watch out for when shopping perhaps.

You're right that this is a bit of a thread hijack, but isn't that what makes these forums interesting?

Re: Lag screw lubricant

#37

Divide it.....

Bill Tindall, E.Tn.

....into 5 lifetime pieces and sell 4/5 of it on Wood Central classified or at your club.

I'll sell 1/5 of my stick for $2 and postage.

Re: Lag screw lubricant

#38

No problem

Bill Tindall, E.Tn.

You won't find me screwing to any tree that has any potential for lumber.

Re: Lag screw lubricant

#39

Jason Roehl in Lafayette, IN

Trigger control!

Jason Roehl in Lafayette, IN

I find I can drive screws or lags pretty well with an impact driver. You can't just pull on the trigger with a death grip and hope you don't break the fastener. With lags, I just watch the socket's labeling--it will spin fast for a while until it's almost home, then it will suddenly only move with the impacts. A little judgement applied as to how many impacts after the free-spin gets a tight lag without snapping it off. With my old drill-drivers (non-impact) I never used the clutch, I would just let my whole arm twist to absorb the shock of the screw hitting home. Very rarely do I break fasteners.

I own a Bosch 18V, and use a Dewalt 18V at work. Both have VS triggers. If it's a smaller screw, I can drive it home without any impacts by going easy on the trigger. Something larger will get several blows before I let off the trigger.

Jason

Re: Lag screw lubricant

#40

Re: No problem---tree screwing--OT

Tom Dunlap

Today my crew had to remove a 52" DBH American elm because it had Dutch Elm Disease. I got the fun of slinging the Stihl 088 to make the felling cut. To make things easier for me I grabbed an 046 to do half the face cut.

Dang !@#%^&?}!!! I hit something! After nibbling out the face I found a surveyor's nail [steel]/bench mark with the plastic flagging still attached!

It was about 10" inside the root flare.

Fortunately I was using the 046 w/a 22" bar not the 088 w/ 38" that would have needed sharpening.

Tom

Re: Lag screw lubricant

#41

Lubricant and strength

Lee Schierer in McKean, PA

I use beeswax. You just scrap the threads across a lump a time or two and you are all set. The wax reduces the torque required by about half.

If you are looking for strength, ordinary lag screws are not very strong and will often snap at the juncture of the thread to the shank. For strength you would want to use Timber Lok Screws which are a much higher grade of steel and they won't break nearly as easily as the common lag screw.

Lee