Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Ruler exaspiration. do you use 64ths?

Posts

Re: Ruler exaspiration. do you use 64ths?

#26

Re: Ruler exaspiration. do you use 64ths?

TomD

What I do is take an eyeball and then I adjust the cut , normally when the measurement falls, I note it's deficiencies and correct whatever comes next, I find this speed sstuff up and is more accurate because I am paying attention, not just relying on the measure.

A tape or whatever with just 1/16th would be fine for me. I eyeball the rest or use calipers. I do work to very fine dimensions, as well as transferring lines, and eyeballing

I never owned one, but a shop with everything in Bobs would probably be pretty good. One concequence of the metric system is that nothing matches anything else in the shop.

Re: Ruler exaspiration. do you use 64ths?

#27

Re: I owned one.....

TomD

Rulers are useful for people following directions, or one's own drawn plans. I noramlly use one and a caliper.

Re: Ruler exaspiration. do you use 64ths?

#28

Re: Where a ruler is used......

TomD

"I never use a story stick. I don' t build something twice so there is no need to record the "story" in a stick. I do use a stick for turned spindles. I could use a measure less but don't find it handy to do so."

I rather see you with a lot of kids and making them their own versions of every project.

Re: Ruler exaspiration. do you use 64ths?

#29

Re: Paralax issues as well

TomD

"I agree it's frustrating to have 1/64th on my starret showing at inopportune times :-). 1/32 would be okay for me, my eyes are not getting any younger.

Other thing to keep in mind with finer increments on a ruler is paralax error, right? 1/64 is easy to mess up if your perspective is not directly orthogonal to the surface being measured... "

With calipers or marking gages used with them. I will often just scratch a line directly on the work, no parallax. But as a general rule, I don't worry about how fine the increment is. Sure everything you say about error is true, but applies to whatever increment the point you wish to transfer occurs at. So maybe I can see a thou, or maybe I can't but, starting with the correct number can't hurt. At least whatever degradation that occurs due to transfer error, does not also have built in a measurement error.

Re: Ruler exaspiration. do you use 64ths?

#30

Re: Ruler exaspiration. do you use 64ths?

Walt

"One concequence of the metric system is that nothing matches anything else in the shop."

It would match if the rest of your shop were metric ;-). I think about 99% of the issue with different measuring systems is simply unfamiliarity. I'll bet you can look at a piece of wood and make a very close estimation of its dimensions in inches and not at all in metric. How do you think someone from Europe or Asia would fare with inches? About as well as you fare with millimeters? The sticker comes when trading beyond one's own borders. I recently bought a 6" machinist's rule off Ebay. It's fractions on one side and decimal inches on the back, .1" and .01". Decimal inches are kinda handy, some of the benefits of metric (just move the decimal point) but of course most shop stuff is fractions.

Re: Ruler exaspiration. do you use 64ths?

#31

Re: Ruler exaspiration. do you use 64ths?

paul-in-plymouth

A few weeks ago there was this thread with complaints about 4R graduations being somewhat inconvenient for woodworking: 1/16” paired with less useful 1/8” on one side and excessively fine graduation on the other side. The OP said he would find “extremely useful” a rule graduated to 1/16” on all edges.

I knew of no such rule at the time, but received this ad for rules from Woodsmith today that almost fill that bill: both scales on one side graduated in 1/16ths and both scales on the other side in 1/32s. FYI.

http://www.woodsmith.com/rules.php?utm_source=WoodsmithTips&utm_medium=email&utm_campaign=10126

Re: Ruler exaspiration. do you use 64ths?

#32

Re: Ruler exaspiration. do you use 64ths?

TomD

""One concequence of the metric system is that nothing matches anything else in the shop."

It would match if the rest of your shop were metric ;-)."

Well that won't happen, Walt. And I am not sure I really want to call that my fault given I learned both systems pretty much from the cradle starting in 1959, and moving on through 11 years of european schooling, by the end of which Canada was metric anyway.

One problem is that the US didn't do what it said it would do, and metrify itself. But even if they had, there would still be decades of perfectly usable tools floating around one would be fool not to latch onto. Then weird stuff happens, like the Chinese/etc... send us decimal tools built on metric threads, so that the wheels and thread cutting tools specify Imperial, but the actual increments are metric. Sound like a plan to you? That is or until recently was standard.

"I think about 99% of the issue with different measuring systems is simply unfamiliarity. I'll bet you can look at a piece of wood and make a very close estimation of its dimensions in inches and not at all in metric. How do you think someone from Europe or Asia would fare with inches? About as well as you fare with millimeters? The sticker comes when trading beyond one's own borders. I recently bought a 6" machinist's rule off Ebay. It's fractions on one side and decimal inches on the back, .1" and .01". Decimal inches are kinda handy, some of the benefits of metric (just move the decimal point) but of course most shop stuff is fractions."

One thing I run into with boats is some of the good designers use metric, others use Imperial. So you can end up with projects in either. I design in inches. But given the superiority of metric in the minds of people who largely don't work with their hands, or measure calories, water temp, or the dimensions of a litre of water. And given what LV was churning out at the time. I used metric for quite a while, but some time ago, I just threw in the towel. I live really in an Imperial world, and I standardized around imperial. Stuff like yogurt is metric, and temps, but building materials are usually metric, all the machines I have are pretty much imperial, bike stuff is metric, etc... Digital callipers are normally more accurate in imperial, the smallest fraction is about twice as large in metric. There is so much insanity it is better not to think about it. My new welder is metric.

Funny I recently started up my post bypass exercise routine. I imagine Canadian medicine is metric, probably world medicine. But the exercise is measured in Imperial. I feel like asking them if they have a changeover year planed and are currently just sucking up on account of the average patron's age.

I cycle in Imperial, it always seems like cheating to express a daily mileage on a tour in metric, I feel Imperial is more honest. Anyway, most of the forums are US (and most of the roads), so I might as well.

Re: Ruler exaspiration. do you use 64ths?

#33

This supplier has

Brian Roberts

A large and interesting variety of rules....at decent prices.

http://www.bandhspecialties.com/catalog.pdf

Re: Ruler exaspiration. do you use 64ths?

#34

Re: Ruler exaspiration. do you use 64ths?

William Duffield

Changing over is going to be difficult. I offer a few more examples of those difficulties:

You might study BugBear's bowsaw plans, reverse engineered in millimeters from an antique bowsaw. Dimensions, mostly in whole inches and a few simple fractions, got changed to incomprehensible, unmemorizable three digit decimal fractions. While not impossible to build one from the metric measurements, it's a whole lot easier to use an Imperial ruler and the original measurements.

I find it much easier to add and subtract, and even do some multiplications and divisions in my head using Imperial fractions. If I have to work in Metric, I have to use a calculator.

Take an arbitrary line segment, and with a ruler and compass, divide it in tenths. Then, using the same tools, divide it in half, then in quarters, then in eights, then in 16ths. The Imperial construction will be done more quickly and more accurately than the metric.

Sometimes, I think we would have been better off, if millennia ago we had developed and adopted the ritual of cutting off our almost useless ring finger at birth, like they do with Cocker Spaniel tails.

Our computer programs would be much more efficient, easier to design, code and test, would execute much more quickly and require less memory if we didn't need to convert between binary and decimal all the time. Moore's law would be advanced by a generation.

Re: Ruler exaspiration. do you use 64ths?

#35

Re: Ruler exaspiration. do you use 64ths?

William Duffield

I'm being picky, but your description needs one correction: While both scales on the obverse face are in sixteenths as you describe, only one of the scales on the reverse face is in thirty-seconds. The other reverse scale is also in sixteenths, but numbered in both directions from the center.

There are also lots of other options. I'm a fan of antique four-fold rulers. My favorite is a Stanley No. 62 two foot four-fold, boxwood, brass bound on all edges. It is graduated in eights, tenths and twelfths on the obverse face face. One rule on the reverse is graduated in sixtheenths . The other rule, similar to an architect's scale, is ruled 1"=1', 3/4"=1', 1/2"=1' and 1/4"=1'. These are for measuring scale drawings in feet and inches.

Another advantage of two foot four-fold rulers is that they work naturally as 6", 12" and 24" rules, depending on how far you open them.

Stanley and others also used to make three foot and four foot four-fold boxwood rulers. You will find them most commonly with one scale in eighths on one face and one scale in sixteenths on the other face. Prices vary, of course, with model number and condition. I paid about $20 for my No. 62.

Re: Ruler exaspiration. do you use 64ths?

#36

Re: Ruler exaspiration. do you use 64ths?

paul-in-plymouth

You’re absolutely correct, as I found out too when I watched the video. My apologies and thanks for the correction. However, the 1/16th-side does fulfill the stated wish of the OP, which is what I wanted to point out.

Your enthusiasm for antique folding rules is infectious, maybe dangerously so. However, I have the measuring tools I need and more, including a few with 4R graduations.

That said, not all 4R graduations are equally good. For many years I’ve used a 6” 4R rule made in LA in the 1970s. This is a nice inexpensive utility rule, but the 1/64th scale was already an exercise in imagination for me when I got it in my 30s and remains so 40+ years later. Then I have a couple 4R rules by Starrette that are so beautifully clear and fine that I can still actually read the 1/64th-scale with only bifocals. I rarely need 1/64ths, but it’s nice to have them, I guess. And if you have them, it’s nice to be able to read them.

More useful would be replacing the 1/8-scale with a second 1/16-scale on the same face, as the OP pointed out. This is what Woodsmith seems to have done.