Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Cutting 3/16 steel rod on the cheap

Posts

Cutting 3/16 steel rod on the cheap

#1

Cutting 3/16 steel rod on the cheap

Gary Smyth

I have to cut approximately 300 2 1/4" pieces from 3/16" x 48" cold rolled steel rod. I do not have a plasma cutter or metal shear. Forget pliers. I do have a 14" band saw and various grinding wheels. Realizing I will lose a blade for wood can I do that? I do not want to screw up the saw. Frankly I don't want to bang these out one at a time. As it is I will need to go through 15 rods to make 300. I talked to a local fabricator who does have a shear but his labor cost alone was a bit over $100. That's $100 I can use to buy stuff. Any alternatives for doing it myself? What blade to use? Commercial pins are priced at $1.59 each.

Re: Cutting 3/16 steel rod on the cheap

#2

Re: Cutting 3/16 steel rod on the cheap

Mark Mandell - Gone Round In New Jersey

Die grinder (air or electric) and 3"cutting disc (buy more than 1) and

hearing protection :D

ps: Alternative is a sawsall with bimetal fine blade

PPS: Forget the wood band saw way way too fast on the blade and no lubrication which is required, even with a steel-cutting blade. Real danger here!!

Re: Cutting 3/16 steel rod on the cheap

#3

Re: Cutting 3/16 steel rod on the cheap

John Foster

I would do some more shopping. The metal shop around the corner from me has an old ironworker. He can pretty much chop pieces off a piece of stock as fast as you can feed it in. The amount you are talking about should take only 15 minutes.

Re: Cutting 3/16 steel rod on the cheap

#4

Got a miter saw?

Ray - Middletown, IN

If so get an abrasive blade, take it outside where the sparks won't hurt anything and have at it.

Ray

Re: Cutting 3/16 steel rod on the cheap

#5

I have. Full body armor?

Gary Smyth

Very late fall I bought a used metal cutting chop saw. Put it into the garage to be checked out in Spring. Never used one -- never thought about it. Out of sight out of mind. I take it the pieces will fly though. If I install a stop and maybe some sort of cover on both the stop and feed side would it be safe to cut more than one rod at a time? Don't want 2 1/4 x 3/16 missiles.

Re: Cutting 3/16 steel rod on the cheap

#6

solution

Bill Tindall, E.Tn.

go to harbor freight and buy a metal abrasive cut off saw. When done sell saw on Craigs list. Will sell easily.

Re: Cutting 3/16 steel rod on the cheap

#7

Re: I have. Full body armor?

George Koch

Gary, I bet you could put all 15 rods inside a piece of 1" pvc pipe and use your chop box to cut them into the short lengths that you need. I think it would cut down on the flying missiles and sparks too.

Re: Cutting 3/16 steel rod on the cheap

#8

Do you know this will work safely?

Bill Tindall, E.Tn.

I don't, so its an honest question. The answer revolves around whether a wood cutting miter/chop saw spins at the same speed or less as a metal cutting chop saw. Exceeding the rpm limit the abrasive bade was designed for could explode the blade.

Re: Cutting 3/16 steel rod on the cheap

#9

Re: solution

Chuck Kettler

We have a 14" metal cut off saw at work. It cuts off a quarter inch 60 Rc S7 center nib in about 2 seconds. Bill's advice will get you where you need to be and the sale on Craig's list pretty quick.

Re: Cutting 3/16 steel rod on the cheap

#10

I've done it a lot...

John in NM

With a 10" Delta chop saw. There are 10" blades available for the correct rpm (around 6,000 IIRC), got one at HD as I recall.

The big steel cutting chop saws (14") run slower than a wood saw, maybe around 3,000 rpm. They also have a bigger arbor, usually 1", so there is no putting a worn down one on a wood chop saw.

Re: Cutting 3/16 steel rod on the cheap

#11

Now a bit confused

Gary Smyth

What I bought, now in the back of a unheated garage is similar to the picture. 14" chop saw for metal. I bought a new black abrasive metal cut off blade, as yet not installed. Is this what you are suggesting as from Harbor Freight? Or am I not identifying the tool correctly?

Re: Cutting 3/16 steel rod on the cheap

#12

Re: Now a bit confused

Joseph Mulherin, sr

Gary, I have used this type of saw many cuts and it does as the blade says it will do. I would take George's idea of the PVC with the 3/16" lengths inside and setup a stop block to get your lengths proper and just go for it.

Re: Cutting 3/16 steel rod on the cheap

#13

correct tool

Bill Tindall, E.Tn.

now let the sparks fly.

Re: Cutting 3/16 steel rod on the cheap

#14

Re: Cutting 3/16 steel rod on the cheap *LINK*

Dick Coers

Throw a cheap Harbor Freight grinder in this and probably get by for less than $50


right angle grinder stand

Re: Cutting 3/16 steel rod on the cheap

#16

"Soft" jaws for holding the stock

Virgil Johnson

Here is an idea to keep the cut pieces from flying. it would require making "soft jaws" for the "vise" on the saw.

Here is a stab at a description. You need two pieces of hardwood about 3/4 x 1 1/4 x 10-12"" long. These will be the soft vise jaws. On the table saw cut a 5/32 rabbet joint 1/4 deep on one edge of the jaw that is fastened to the solid part of the vise. The5/32 rabbet forms a groove for the 3/16 rod to sit in while cutting. Fasten the other soft jaw without the rabbet to the moveable jaw. The end of the jaws will be positioned the length of the part to be cut away from the edge of the blade. The rod is supported on both sides in this manner and the end of the jaw becomes the stop for the length. Only plunge deep enough to cut through the steel but not through the jaws. And of course try this at your own risk......

Re: Cutting 3/16 steel rod on the cheap

#17

That will do it

Keith Newton

I like the idea of the stack being fed through a larger pipe, but if they want to chatter around and twist, you may want to try trapping them between two wooden jaws, stacked.

I would tape the far end of the stack together to keep them indexed.

If you have a little flexibility on your length, I would suggest setting a stop block, but stopping a little shy of touching it. I think one of the causes for flying parts is that the diagonal length is a little longer than straight down the center, causing them to jam if you are hard against the stop.

And on longer stock, the heat caused by abrasive blades causes expansion to the metal, it is useful to allow gravity to pull the end down a little to open the cut so it doesn't pinch on the sides of the blade, robbing power.

Re: Cutting 3/16 steel rod on the cheap

#18

Rick L

Re: Another option

Rick L

As usual most posters don't give enough info of what they are making so other options can be suggested. Spring pins 3/16" x 2-1/4" are $11.00 a hundred.

http://www.mcmaster.com/#steel-spring-pins/=w00u7c

Re: Cutting 3/16 steel rod on the cheap

#19

You are out of touch.

Virgil Johnson

The shop owners moto is "Why buy it for 2.00 when you can make it for 10.00"..:-)

Re: Cutting 3/16 steel rod on the cheap

#20

Re: You are out of touch

Mark Nowicki

:D :D

Re: Cutting 3/16 steel rod on the cheap

#21

Jack Guzman from Maine

tape

Jack Guzman from Maine

Gary,to gang those why not bundle them together and wrap the whole thing with scotch tape or similar. Then you can safely chop the bundle and use solvent to separate the tape after.---Jack

Re: Cutting 3/16 steel rod on the cheap

#22

Divergent view

Bill Tindall, E.Tn.

I have cut rebar into sections. The cuts are just are few seconds. I would rig a stop and cut them singly. By the time one rigged the bundle the task would be done cutting singles.

Re: Cutting 3/16 steel rod on the cheap

#23

Not really...

John in NM

I would definitely buy them instead at that pricing if roll pins would work. I can make more money, but my time is limited. I've seen more than a few manufacturers go out of business due to thinking that making everything in house saves them money.

OTOH, roll pins might not suit Gary's needs, depends on what he's up to.

Re: Cutting 3/16 steel rod on the cheap

#24

Shear don't cut *LINK*

Tom Dunlap

If you use an abrasive wheel you're going to have to dress the cut ends, probaby using a belt sander

I did. A search on: 3/16" rod cutter. And found this manual cutter for $100. The end of the rod should be cleaner which will make dressing easier


http://www.toolfetch.com/heck-industries-sphs8-hand-shear-cuts-up-to-3-16-steel.html?utm_source=google&utm_medium=cse&utm_term=SPHS8&gclid=CjwKEAiA9qCnBRCb7ZDhvaHSyicSJABGFFHtSjASc5ny0ybQLrU2L4DeagwJ70EQs_BZmon-uceaLxoCjg3w_wcB

Re: Cutting 3/16 steel rod on the cheap

#25

Thanks but roll pins not acceptable.  However

Gary Smyth

should you be able to discover 2 1/4 solid 3/16 cold rolled steel pins at someplace including the following I've searched --MSC, Grainger, Small Parts, Little Machine Shop, Shop Tools, B&G Industrial Supply, Micro Mark or other catalog/supplier I'm interested.