Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Hitachi M12V Router Table Plate

Posts

Hitachi M12V Router Table Plate

#1

Hitachi M12V Router Table Plate

J Zimmerman

I have a relatively ancient Hitachi M12V mounted in a router table. I determined my router table platform was too small so I started casting about for a new table and insert plate. I checked a number or sources but did not find a pre-drilled plate for the M12V. Would anyone have a source for same that they could recommend?

Re: Hitachi M12V Router Table Plate

#2

Re: Hitachi M12V Router Table Plate

John McGaw

If you are looking for pre-drilled you may be a long time looking. On the other hand, it is pretty easy to drill your own (it has to be easy, I've done it). The things to watch out for are achieving perfect centering, for which there are special centering bits available, accurate drilling of the clearance holes for the screws, and proper countersinking for which you might need to buy a true countersink. I'd suggest a beefy phenolic plate. Oh, and you might want to source some new screws since the ones which mount the standard Hitachi base are probably too short for a thicker phenolic plate. You will need to go through some gyrations with removing springs and such in the router but it is pretty self-explanatory once you take a look at how it goes together.

Re: Hitachi M12V Router Table Plate

#3

no centering tool needed

Dick Coers

if you put the center hole in last. I always mount the plate on the router and use a router bit to "drill" the center hole. Works great. If you need a bushing recess, I use a rabbeting bit for that.

Re: Hitachi M12V Router Table Plate

#4

Rousseau 3509

Rod Peterson—Ormond Beach, FL

Has removable center rings to accommodate all size bits. There are concentric rings cast on the bottom to help you locate your holes for the router. To be honest, you're way over thinking this. Router plates are not difficult to mount correctly.

Rod

Re: Hitachi M12V Router Table Plate

#5

Re: Hitachi M12V Router Table Plate

Ray Carson - Lawrenceville, NJ

Had a Rousseau setup for years. Loved it. Changed it out about 5 years ago for a Woodpecker model with a Raizer lift. (sp) The Woodpecker has more interchangeable ring options.

Ray

Re: Hitachi M12V Router Table Plate

#6

Re: Hitachi M12V Router Table Plate

Joe shelton

Lee Valley has a great replacement base with all you need, including instructions, for installing the base and letting in for table use or quickly popping the router out for handheld use. Cheap, too.

Re: Hitachi M12V Router Table Plate

#7

Re: Hitachi M12V Router Table Plate

Terry in Edmonton

I had a 12V with the Lee Valley plate for about 5 years and it worked very well. I finally upgraded to a Jessem when the router packed up.

Re: Hitachi M12V Router Table Plate

#8

Re: Hitachi M12V Router Table Plate

Tony - Memphis

I probably have the same router in my table. I have been using a Woodhaven setup for many many years. Works great.

Tony

Re: Hitachi M12V Router Table Plate

#9

Re: Hitachi M12V Router Table Plate

J Zimmerman

Thanks to all for the input and advice. There does not appear to be a commercially available route table plate that is pre-drilled for the Hitachi M12V. Although my M12V is about 8 years old, it has seen very limited duty to the tune of about six to eight weekends per year, that I'm place it into service in my new Rocker Router Table. In that their are no pre-drilled plate sources, and the Rockler router tables plate sizes are about an inch narrower than what I would consider standard, I'm going to acquire some sheet phenolic and custom make the table plate for the Hitachi.

Now, would anyone be able to recommend a source for 0.375 sheet phenolic?

Again, input and advice is greatly appreciated.