Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Carving Board Gift

Posts

Carving Board Gift

#1

Carving Board Gift

Bill Tindall, E.Tn.

Carving Board

PIC 1,2





Recall I was attempting to recreate a Dansk cutting board for daughter. This design is more practical than any I have used. In use the liquids run to the deep end and not onto the table.

Step 1 was to use the lathe to make a tray. I didn’t have a lathe large enough to turn this 16” platter so my friend Harold Pannell turned the tray. Then the question was how to slope the lip. The lip slopes from 1 1/8” high to near nothing. Several suggestions were offered here on WoodCentral. I did consider hand sawing it and cleaning it up with a plane, but the difficult to plane end grain discouraged that idea.

PIC 3,4,5







Following one suggestion I made a sled for the router and sloped the rim by fixing the tray at an angle in the sled and mowing off the rim as shown in the pictures. I still had to hand plane the top surface of the lip. The router left the end grain open. A cleat is added to the bottom so that the rim of the “tray” is level with the surface the carving board sits on and the bottom of the tray slopes to the back. A slather of cooking oil is added and it is ready for her birthday.

It turned out to be so easy I intend to make other cutting boards of this practical style.


Re: Carving Board Gift

#2

I like it, may I suggest????

Barry Irby

I may steal this idea and make some myself. Its a beauty.

My suggestion would be to turn the rim thinner, more vertical, with a good cove at the bottom. With the profile of the rim as tapered as you have it, it got much wider as you cut it down, robbing you of some space.

Re: Carving Board Gift

#3

The only thing I'm not too keen on,

Keith Newton

is the cleat on the bottom. Even if it never get any meat juices under it, it will still hold water from washing, while everything else gets to dry more equally. I think a dowel glued into a shallow hole, sticking out to the same height, would give a 3 point stance just as stable, with less potential for later problems.

Even if you leave the cleat, i hope you slotted the holes.

Re: Carving Board Gift

#4

cleat seems to not be a problem

Bill Tindall, E.Tn.


Pictured is the original carving board that the new one was patterned after. I considered legs of some sort because they would be easier to do, but the cleat looks better and it has done fine on the original for 49 years.

Re: Carving Board Gift

#5

Well, I can't argue with that, *LINK*

Keith Newton

But I might point out that you did make a major change from the original when you turned the grain to short. While I like the way it looks, having that cherry sapwood turned up like that is quite a bit more absorbent than the Walnut heartwood side-grain.

Bill, I know your grasp of the chemistry of finishes is way beyond anything I'll ever know, but I've started keeping CPES onhand for some of the exterior millwork projects that I've been making, and using it on some of my other projects, like this one. It is extremely thin, and slow drying which helps it soak deeper. after it has set up within the cell walls, they are no longer prone to decay, partially by becoming plastic, but also by not being so absorbent. Then, I really like how well a single coat of wipe on poly, or anything else looks great after I've used it, even if it were a near punky wood. I was wondering if you have ever tried it?


http://www.amazon.com/TotalBoat-Penetrating-Epoxy-Quart/dp/B00J36WRV2/ref=sr_1_1?ie=UTF8&qid=1419175918&sr=8-1&keywords=cpes

Re: Carving Board Gift

#6

Re: Carving Board Gift

Matt Robinette

Looks nice,I am sure it will he appreciated.

Re: Carving Board Gift

#7

Haven't tried it

Bill Tindall, E.Tn.

For cutting boards I soak them with cooking oil. It keeps the water out. Some of these oils have enough reactive sites to partially cure over time and they make a durable film.

Re: Carving Board Gift

#8

Re: Haven't tried it

TomD

Bill probably knows this, but if you avoid healthy oils or oils with additives like Vitamin E, they are more likely to harden off. Like walnut oil with vitamin e may not harden, but it will if it is just real walnut oil.

Yeah the endgrain was a no for me. Mostly because it would be so much easier and safer to turn without it. But also because of the sinkage and fragility.

I imagine with variable centers you could turn a slope in the piece integrally, though it might end up pretty heavy.

I get how one end it deeper, but it would be pretty easy to cut so that it was flat and there was just a bigger reservoir for juices. Presumably current Eu rule would make the uneven cutting surface illegal, like my Inca table saw.

Re: Carving Board Gift

#9

Re: Carving Board Gift

Jim O'Connor

I just finished turning one out of 1 1/8 birch strips, 13 1/2 in. dia.

I glued a mounting block on the back and then screwed a face plate on with spacers under one edge so that it have the deep end running the grain of the wood strips. I took the deep end down 3/4 of an inch. Needless to say this wobble turning is kinda fear puckering but it worked out. Next time I would turn the entire depth in normal mode to reduce the vibration this off center one caused, then tip the face plate to make the rim. It was a challenge but worth ;it.

Re: Carving Board Gift

#10

pucker factor

Bill Tindall, E.Tn.

Can't argue with success, but in my case the disk was nearly 16 inches and the depth 1 1/8. No doubt an experienced turner could handle that off set. Others would find the router sled a less stressful solution.