Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

95" bandsaw blades instead of 93 1/2" ?

Posts

95" bandsaw blades instead of 93 1/2" ?

#1

95" bandsaw blades instead of 93 1/2" ?

Joe Pack

I can buy a stack of bandsaw blades that, according to the hand-made tags, range from 93 1/2" to 95" long. My Jet 14" bandsaw calls for 93 1/2" blades. Do you think the 95" blades might work on this saw?

I probably will buy the stack anyhow...$30 for 24 blades...and at least some will fit. The box for some of them is labeled "Marvel." Evidently that company used to make blades for woodworking, but now makes only steel/metal machinery and blades. Any information on this brand?

Re: 95" bandsaw blades instead of 93 1/2" ?

#2

Re: 95" bandsaw blades instead of 93 1/2" ?

Yonak

Joe, if the 95"ers don't work you may be able to re-sell them. I had a Powermatic band saw that, I think, used 95" blades.

I wonder if you could put an extra set of tires on your band saw to take up the slack ? They'd be pretty hard to get on but then you'd have an extra set of tires if you ever needed them.

Re: 95" bandsaw blades instead of 93 1/2" ?

#3

Re: 95" bandsaw blades instead of 93 1/2" ?

Dick Coers

If they don't work, buy a silver solder kit and make them shorter. I use silver (hard solder) solder to make up to 3/4" blades. I use a stationary disc sander to scarf the joint. It's easier than you think.

Re: 95" bandsaw blades instead of 93 1/2" ?

#4

Re: 95" bandsaw blades instead of 93 1/2" ?

Joseph Mulherin, sr

There is a video on You Tube showing what a guy setup for making his soldering joints.

Re: 95" bandsaw blades instead of 93 1/2" ?

#5

Re: 95" bandsaw blades instead of 93 1/2" ?

roger lance

Joe.....a friend recently told me that a local sharpening service also welds bandsaw blades for a very inexpensive price......regrettably, that was right after I threw away a blade that had failed at the weld.....I'd check this out.....you might be in line for a "you suck".

Re: 95" bandsaw blades instead of 93 1/2" ?

#6

Re: 95" bandsaw blades instead of 93 1/2" ?

Mark Nowicki

IMO, not worth the bother.

In my experience, bulk buys of this kind usually end up in the garbage, after cluttering up the shop for years.

Is the regular cost of bandsaw blades, bought as needed, a budget breaker ?

Mark

Re: 95" bandsaw blades instead of 93 1/2" ?

#7

Re: 95" bandsaw blades instead of 93 1/2" ?

Joseph Mulherin, sr

Roger, I never said I was going to buy the parts to make this jig up...just told you people that there was a video showing a guy who did have it and did a blade online to show it worked.

I, myself, buy my blades from Shopsmith

Re: 95" bandsaw blades instead of 93 1/2" ?

#8

Let me know if you want to sell the 95"ers

Henry Higginbotham

My Powermatic 141 specifies 94-96 inch. I usually keep 1/8" or so on that saw, but could use others if they're a good deal.

Re: 95" bandsaw blades instead of 93 1/2" ?

#9

Joe, all you need to do, is open the saw cover,

Keith Newton

And measure from the table to the center of the top wheel, then take the blade off, and see if it will go 1" higher than that. If it will, then you don't need to do anything but put it on and go.

If those are new blades, surely there would be some good ones, if the tooth configuration is something you need.

Re: 95" bandsaw blades instead of 93 1/2" ?

#10

Re: 95" bandsaw blades instead of 93 1/2" ?

Joe Pack

Thanks for the information.

Re: 95" bandsaw blades instead of 93 1/2" ?

#11

Re: 95" bandsaw blades instead of 93 1/2" ?

Larry Clinton At Frankfort, (Central) Indiana

Shouldn't be any problem to have a saw sharpening service shorten them if you have a problem. Also any metal working shop that has a metal band saw should be able to cut and reweld them very cheaply. (Almost every metal band saw I have used over the years is equipped with the cutter / welder / anneal and grind attachment built in ~mounted on the side of the welder.) It only takes two to five minutes to properly produce a blade as good as any manufacturer welds!

Re: 95" bandsaw blades instead of 93 1/2" ?

#12

Re: 95" bandsaw blades instead of 93 1/2" ?

rfcomm2k

To Larry in Frankfurt, IN,

Getting a saw sharpening service to shorten the blades IS a problem. Many sharpening services will ONLY sharpen, not re-weld. And those that will re-weld make it so costly that you can almost replace the blade for the same cost, especially if you are purchasing blades in bulk as the OP seems to be doing.

To Joe Pack, follow the advice of Keith Newton. With a blade on and properly tensioned measure from top of table to center of upper flywheel. Remove blade, crank it all the way to the highest point upper wheel will go, and measure again. If it is 1" or more then you can use those 95" blades.

BTW, where did you come across this bargain? I would like to make a similar purchase, but I need 145" blades (144.5-148 will work).

Re: 95" bandsaw blades instead of 93 1/2" ?

#13

Re: 95" bandsaw blades instead of 93 1/2" ?

Larry Clinton At Frankfort, (Central) Indiana

Don't know where you live but in my area there is one local sharpening service, they are a full service shop - sharpening band and circular blades with state of the art CNC grinders, and are quite reasonable for both new blades and service of older blades. There are at least 5 tool shops within 25 miles of my home and all are fully capable of making and or modifying band saw blades, from the prices I have paid for work from some of these shops they are very reasonable for minor work like this, especially if you have a quantity of blades to shorten. I was an Engineer for about 40 years in a manufacturing facility and used these shops frequently for work our tool room was too busy to finish.

Re: 95" bandsaw blades instead of 93 1/2" ?

#14

Re: 95" bandsaw blades instead of 93 1/2" ?

James Heisbert

I got my blades online and they custom weld to length band saw blades.