Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Follow Up - where to get Hose Adapter?

Posts

Follow Up - where to get Hose Adapter?

#1

Bart Goldberg

Follow Up - where to get Hose Adapter?

Bart Goldberg

Ok, so I decided on getting the Makita Finish sander as was recommended by several of you. Now I need to find where to get a hose adapter to connect the 7/8" OD port of the sander to the 1.3" OD of my vacuum hose?

FYI - I already checked out Rockler and couldn't find an adapter of the right size.

Thanks

Bart

Re: Follow Up - where to get Hose Adapter?

#2

Re: Hose Adapter

Mark Mandell - Gone Round In New Jersey

Try Klingspor or Penn State

Re: Follow Up - where to get Hose Adapter?

#4

All mine came from the plumbing isle...

John in NM

Those rubber things with hose clamps that I would never dream of using on a drain are perfect for this application :D

Re: Follow Up - where to get Hose Adapter?

#5

Bart Goldberg

Re: All mine came from the plumbing isle...

Bart Goldberg

John,

interesting idea - I will have to check that out.

Thanks

Bart

Re: Follow Up - where to get Hose Adapter?

#6

Re: Follow Up - where to get Hose Adapter?

Walt

Here's another candidate - also found at Woodcraft. It works well with Fein vacs

http://www.woodcraft.com/Product/815898/Fein-Step-Adaptor.aspx


img

Re: Follow Up - where to get Hose Adapter?

#7

Duct Tape....fixes everything


Re: Follow Up - where to get Hose Adapter?

#8

Re: Follow Up - where to get Hose Adapter?

Larry in NW Ohio

I know this sounds silly, which is fairly normal for me. I have made a few out of hard wood. I made any size up to 4". That is the highest because that is the biggest I ever needed. They do very well. Larry

Re: Follow Up - where to get Hose Adapter?

#9

Re: Follow Up - where to get Hose Adapter?

ray k

I've my own adapters from pvc pipe or fittings from big box stores. I get pipe or fittings that are pretty close to the size that I need and heat them up with either a heat gun or even over an open flame (be careful of course). BE SURE TO DO THIS OUTDOORS, as you don't want to breathe the fumes. When it heated enough, pvc with be flexible and almost floppy. At this point, just form it over whatever opening you need. I've used this technique to widen fittings and the same process can be used to shrink fittings (by using a piston ring compressor) to tighten down the circumference of the pvc. Your final end product may not look like a storebought adapter, but it works just as well. I found this especially helpful for adapting metric dust chutes to 4" hose.

Re: Follow Up - where to get Hose Adapter?

#10

Re: Follow Up - where to get Hose Adapter?

William Duffield

That Fein connector works perfectly to connect a Festool CT CleanTec Dust Extractor hose to a SawStop blade guard.

Re: Follow Up - where to get Hose Adapter?

#11

Bart Goldberg

Re: Follow Up - where to get Hose Adapter?

Bart Goldberg

Yeah - thats the one I ordered - not quite the right size tho, so will need to figure out how to make the 1" ID meet the Makita 7/8" OD (duct tape I suspect).

Re: Follow Up - where to get Hose Adapter?

#12

Re: Follow Up - where to get Hose Adapter?

rfcomm2k

I finally had to MAKE and adapter from a scrap of wood. I used a 7/8" forstner bit to start a hole in a block of wood, then switched to a 1 3/8" hole saw. After cutting the piece out I went back and finished the center hole with the forstner bit. A little tuning with some 100 grit sandpaper made it fit my vacuum hose so well I did not need to clamp it (hint here, slightly taper it so it jams into hose).

Re: Follow Up - where to get Hose Adapter?

#13

Bart Goldberg

This is how I resolved the issue *LINK*

Bart Goldberg

Thanks all for your many great ideas on how to fit the connections from my Fein vacuum to my new Makita sander. As it turns out, the fitting that Mark pointed me to fit like a glove. FYI - I found it on Amazon, as well as at Woodcraft.


Fein Vacuum Adapter

Re: Follow Up - where to get Hose Adapter?

#14

Re: This is how I resolved the issue

William Duffield, on the Cohansey

Yeah, you can find just about anything on Amazon cheaper than you can find it at Woodcraft (except from certain manufacturers who insist on everyone selling their goods at the same price). I just mention Woodcraft because I used to work for one of their franchises, and I am familiar with what they carry. I also find it helpful to be able to walk into a brick and mortar store and get honest advise from real woodworkers. Woodcraft, of course, isn't the only one who provides that service. Amazon's reviewers can be very helpful, too, sometimes just because there are so many of them.

Re: Follow Up - where to get Hose Adapter?

#15

Bart Goldberg

Re: This is how I resolved the issue

Bart Goldberg

Bill,

I have nothing against Woodcraft, in fact I like them very much. However, the closest Woodcraft for me is over an hour drive, and since I'm an Amazon Prime member, I get free 2 day shipping.

Bart