Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Spice Box 5- Profiling the drawer dividers

Posts

Spice Box 5- Profiling the drawer dividers

#1

Spice Box 5- Profiling the drawer dividers

Bill Tindall, E.Tn.

Shaping the divider front edge

PIC1



As seen in the photo of an earlier made spice box the dividers have a bull nose profile. This profile leads to the necessity of mitering the intersections as previously described, so why the bother? The tiny drawers have flat bottoms so as to not waste space. This decision leads to a problem. How to stop the drawers in some precise predictable position? I don’t have an answer to that question. Do you?

An alternative is to not stop them in some precise predictable position. The drawers can be made a bit shorter than the case depth (which will change with humidity), and let the drawers stop against the back of the case. With a rounded profile on the dividers it is less offensive to the eye for the drawer front to not be precisely positioned relative to the divider front. The drawer fronts wind up more or less where the bull nose transitions to flat and that seems to look ok if it varies a bit.

PIC 2



I like to scrape these bull nose profiles. The slight irregularities in my rendition of a scraped profile catches the light nicely. I needed to make a scraper with about a 3/8” diameter profile. I use a bow saw a lot for trail maintenance and kindling. Sandvick blades are the best, but I seldom see them for sale. I scored a 24” blade and cut it back to fit my 21” saw, leaving the cut-off. Note: Sandvick bow saw blades make dandy scraper stock! Don’t forget to polish the faces or it won’t cut well.

PIC 3



The final picture shows the 72 drawer parts needing to be dovetailed together. More on the later, maybe a LOT later.

Re: Spice Box 5- Profiling the drawer dividers

#2

Re: Spice Box 5- Profiling the drawer dividers

roger lance

Bill.....love your work.....my e-mail continues to need repair.....but I did receive your message and since I am a new reloader, I've asked a number of experienced reloaders, consulted various reloading manuals, and even have a call into Federal but have not heard back from them as yet. The main theory that I'm hearing is that your loads may be too high and that these rounds should be loaded at or near the minimum. The theory is that these cases are splitting due to high pressure or the brass has been loaded numerous times with the necks being stretched and trimmed repeatedly and the cases are at the end of their life. Your brass is still available....maybe try some new rounds to see if your issue continues. Be safe.

Re: Spice Box 5- Profiling the drawer dividers

#3

Stops

Mark Mandell - Gone Round In New Jersey

1. Make your drawer backs to fit with 1/8" clearance under the dividers.

2. 1/2" in from the front edge of each divider (and the top), drill one or two small holes in each drawer space.

3. After inserting the drawer, install a small screw into the hole on the underside of the divider, leaving the screw head proud enough to catch the drawers' backs. Easy to do with a "L" screwdriver. If you wish the stops to be "non-marring" on the drawer backs, use the screws to hold a small rubber plumbing washer.

To remove a drawer, simply unscrew the stop(s).

Re: Spice Box 5- Profiling the drawer dividers

#4

Re: Spice Box 5- Profiling the drawer dividers

Rum

My naive approach would be to make the drawers a smidge shorter and put stop blocks or shims in the back of the drawer cavity to make it stop spot on the spot.

Having said that the shadow lines from the profiled faces certainly would make that easier and imho look really nice to boot :D

Also wow so many dovetails so very many :O

Re: Spice Box 5- Profiling the drawer dividers

#5

Re: Stops

Barry Irby

I have used Marks method. You can make the drawer back and 1/8 or 1/4" low and they will miss the stops and come right out. Or if the geometry is right, you can cut radius on the bottom of the drawer sides at the back and the drawers will come out if you lift the front upward when it hits the stop.

Re: Spice Box 5- Profiling the drawer dividers

#6

Addendum.....

roger lance

its also possible that your brass is old and old brass can become brittle (hard and inflexible).....some reloaders will anneal their brass to keep it pliable.....especially in the neck which undergoes the most alteration in firing and reloading.

Re: Spice Box 5- Profiling the drawer dividers

#7

Re: Spice Box 5- Profiling the drawer dividers

Chuck Kettler

I miss east Tennessee for a few reasons. Learning more woodworking from Bill is high on the list. Hands on in his shop got me started and these articles help keep me going.

Re: Spice Box 5- Profiling the drawer dividers

#8

Re: Spice Box 5- Profiling the drawer dividers

Doug Reynolds

I took a spice box class from Steve Latta. He glues the drawer bottom to the drawer sides directly i.e., no groove, so the drawer bottom can be left a little long and planed to stop when it hits the case back. He said he had no problems with this cross-grain glue up due to the thinness of the stock and the very small size of the drawers. I still try to make all by drawer stock, especially the bottoms from quarter sawn stock.

Re: Spice Box 5- Profiling the drawer dividers

#9

Good tip....however

Bill Tindall, E.Tn.

That is a tip I will use. Thank you.

However, the case sides will come and go. The drawer length will not. So indexing the drawer position off the back of the case will result in varying drawer position as humidity changes, mitigated by the bull nosed divider fronts. Which, I suppose, is why the fronts are bull nosed.