Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Little shop improvement

Posts

Little shop improvement

#1

Little shop improvement

McKay

Because I spend so much time in the shop, I decided to make it a little more homey. I spent 31 years on cement floors teaching shop and now my feet are telling me that I need to do something to get a small amount of comfort. As I can afford the 3/4" osb and 2x4s, I am laying down a floor.



I have 2 rows down and 5 more to go.

I also thought that improving the ambiance was necessary. I started with a sheetrock wall and put up some pine that I re-sawed and put on the walls.



Here is a picture of the newly put up shelves. I use these to put off cuts that I can not bring myself to throw away.



Below the shelves, I have a denray sanding table, sink (not plumbed but a bucket that I have below and dump), and a storage table with misc. stuff that I use in my marquetry.

I have it heated in the winter with gas and cooled with a swamp cooler in the summer. (No the moisture does not have an effect on projects as the RH here is so low). Hope you enjoy.

Re: Little shop improvement

#2

Ellis Walentine

Re: Little shop improvement

Ellis Walentine

Awesome improvements. You're going to really appreciate that new floor. Thanks for posting.

Re: Little shop improvement

#3

Re: Little shop improvement

roger lance

Looking good.....and good ideas.....just makes sense to make these improvements to our shops.....makes our time there so much more enjoyable.....interested to hear how you are physically feeling with that wood floor after awhile.

Re: Little shop improvement

#4

A.J. Hamler

Those 2x4s

A.J. Hamler

Are you affixing those to the floor in any way, or are they floating?

Re: Little shop improvement

#5

Re: Little shop improvement

phillip Medghalchi

McKay, you may want to consider putting those anti fatigue mats where you stand the most, because you already put woo d down, the other thing that would help is putting gel insoles inside your shoes to take impacts off you knees & hips. Other than that I think the shop is coming along like log cabin workshop that's relaxing. Well, done.

Re: Little shop improvement

#6

Floating on floor


Re: Little shop improvement

#7

the reason...

McKay

I am putting the wood down is to get rid of mats. I have used HD locking mats, horse stall mat and door entry mats. I couldn't stand needing to move them or kicking them every time that I moved a rolling cart or walked. (It seems that they were always tripping me. Maybe I am a clutz.) I also have gel souls.

Re: Little shop improvement

#8

Re: Floating on floor, those 2x4's???

Barry Irby

McKay, Are your 2x4's Treated? Resting on a slab they probably should be. If the are treated, did you dry them thoroughly first. (treated 2x4's tend to turn into pretzels as they dry)

And I see you have them running the long way of the panels. OSB is significantly stiffer one way that the other and is intended to run across the supports. Hope you are putting the supports closer together. Not a bad place to put some foam insulation. May not be a bad place to put some insecticide either.

(Don't get me wrong, I'm not being critical, in fact I wish I could get motivated enough to do the same thing in my shop.)

Re: Little shop improvement

#9

Barry

McKay

I have the sleepers 16"oc with off cuts placed in the middle for additional support. The treated lumber is on the outside wall next to the course of cinder block. In this dry climate, (Utah), about the only pests that I have to contend with is spiders and grandchildren. (spiders are nasty and grandchildren are fun)

Re: Little shop improvement

#10

Re: Barry

Barry Irby

You are lucky to be in a dry climate for this project at least. Here in humid Southside Virginia, the termite capitol of the eastern seaboard, that would be condemning those sleepers to a short miserable life.

Still think its a good idea to provide some cross support between the sleepers, especially at the end joints.

Re: Little shop improvement

#11

Kneale Brownson

Rot

Kneale Brownson

I once tore up flooring over a slab where they had put vinyl on top of particle board that was supported off the slab by strips of tempered hardboard. Of course, the latter was turned to mush by moisture.