Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Sanding pine boards

Posts

Re: Sanding pine boards

#26

Re: Festool 125

Jesse Cloud

Festool recommends that you turn the vac to one of the lower speeds. The 8 hole paper is designed to maximize air flow and if the vac is sucking hard (OK for routing and Dominoes), then it just pulls the workpiece into the paper and defeats the purpose.

I generally leave the sander at high speed and the vac at medium to low speed. Try varying the vac speed, when you hit the sweet spot it will feel right.

Re: Sanding pine boards

#27

Re: Just being picky

William Duffield

The Festool paper that fits the RO125 and ETS125 models are either 10 hole (older) or 28 hole (newer), not 8 hole. Perhaps the most important hole is the one in the center of the disc, which is used to pump air from the sander's cooling fan to the bottom of the disc, where it pushes the dust out to the circle of 9 holes that are very close to the perimeter (for much more effective dust collection) and also provides lift to the sander itself.

Re: Sanding pine boards

#28

Re: your are using stearated paper...right?

William Duffield

Why use more expensive stearated paper on bare wood?

If Adam had specified southern yellow pine, I would understand the potential problem with resin build-up on the paper, but since he said just "pine" I assume he meant white pine, and should have minimal problems with paper loading.

Re: Sanding pine boards

#29

sanding pine and sand paper

Bill Tindall, E.Tn.

First a disclaimer, I have zero experience with electric random orbital sanders. However, in the past I sanded enough that I invested in an industrial quality air driven ARO brand ROS and the 18 cfm at 90 psi compressor to feed it air. I still have and use it but I don't buy paper for it as often. My sander does not have vacuum. The exhaust port for the air blows most of the dust off while sanding......outside only!.

I don't work much pine. It is too soft and I don't like dealing with the resin. I use poplar for house trim.

Stain grade pine will be one of the "soft" pines. It may be eastern white pine or a western soft pine. In the green state any of the pines are laden with pitch. For furniture work this pitch must be "set" which is done at high temperature in a kiln. Setting is just the volitilization of the more volatile resin components rendering what is left less sticky and less subject to bleed. It is not a stretch to imagine that the lumber that shows up at Home Depot may have been dried more, or less, hot with the pitch more, or less, set.

Get the lumber hot and the remaining resin will become sticky. Anyone sawing pine already knows this fact from noting build up on the saw teeth. Care must be taken when using belt or drum sanders to not clog the grits with resin and dust. I clogged an 80 grit drum belt in minutes sanding white pine.

In the case of my ROS sanding paper the finer grades typically come with a coating to repel sticky stuff, be it finish or resin. This paper is commonly called "stearated paper" because in the past the coating was a metal salt of stearic acid. I don't know if this material is still used or something else. In any case this paper is typically white. If this paper costs more, it is certainly not significantly more and I think no more for what I buy.

As a test I took a piece of planed KD eastern white pine and sanded it with 180 grit Klingspor stearated paper with my ARO brand ROS. This grit removed planer marks quickly and left a finish ready for stain, one step.

Re: Sanding pine boards

#30

Dale Lenz

Re: makes no sense

Dale Lenz

It works, Bill. It's difficult to argue with success.

There maybe other ways and I'll be glad to try, but slowing the sander down solved the problem.

Re: Sanding pine boards

#31

Re: problems at 220?

Keith Newton

That was my thought as well.

There might be an exception though. On a few occasions, I have loaned , or had newbies use the RO sander, who would bump hard up against inside corners, which mushroomed the edge of the pad. This lump under the paper might produce a problem.

Re: Sanding pine boards

#32

What's the difference.......

Bill Tindall, E.Tn.

I won't argue with data. It would be nice to know the differences between air driven sanders and what you are using that results in this counter intuitive phenomena. If I forget to turn the tank on, the pressure drops, the speed drops and the surface quality suffers. The ROS is cross grain scratching much of the time. Do that at hand sanding speed and we all know the result. As a result, for a time the air driven machines worked toward ever higher rotational speed topping out above 10,000 rpm. Mine whines like a router.....or dentist drill!