Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

How to compress bulging bookcases?

Posts

How to compress bulging bookcases?

#1

How to compress bulging bookcases?

Brint in Richmond, VA


After the top shelf on this bookcase fell down for the third time in a year, I took a closer look and discovered that the case sides had begun bulging outward.


In all fairness, these bookcases have served me very well for over 25 years, especially considering that they're made of veneered particleboard.

Each shelf has a groove cut into each end, which fits over removable wire supports that stick into pre-drilled holes in the case sides.



In bulging outward, the sides have pulled the wire supports out far enough from the grooved shelf-ends so that they lose their purchase and the shelf falls.

Regrettably, there is no fixed center shelf to keep the case sides together; if there were, then I likely wouldn't be having this problem. That said, I'm leery of trying to glue or screw in the center shelf now as a way of bringing the sides back in, simply because I'm working with 25-year-old particleboard all around and I'm not confident of its holding power.

In my dreams, I simply affix a 12' invisible pipe clamp to the center back of the three bookcases and squeeze them together. In reality, the only immediate solution I see is to fashion myself some new wire supports that extend farther in (toward the shelf grooves) from the case sides than the current ones - but then I'm afraid the sides will continue their bulging journey outward.

Does anyone's experience with particleboard suggest that fixing the center shelf might actually work? The shelves are 30" x 11-1/2" x 5/8". Thanks to anyone who can offer a suggested remedy.

Re: How to compress bulging bookcases?

#2

Re: How to compress bulging bookcases?

Keith Newton

There is some KD hardware that is a plastic 10mm fowl, which press into a hole near the end, com the bottom., then has a screw which screws into the side. The screws are made to bite this material. Some are double, but I have some single.

Just google 32mm KD fittings.

You may need to glue solid wood spline in that groove before drilling, to keep it from blowing out .

Re: How to compress bulging bookcases?

#3

One solution

Lee Schierer in McKean, PA

With particle board construction, eventually the shelves will sag and the sides will bow from the weight of the books. What is needed is a fixed shelf attached securely to each side part way up each section. You may need to attach every other shelf to the sides to hold the sides in the proper vertical position.

Lee

Re: How to compress bulging bookcases?

#4

Re: How to compress bulging bookcases?

Bill Houghton, Sebastopol, CA

I'd explore the option Keith suggests; but if all else fails and if you can stand a little inelegance in the design, you can fasten a solid wood cleat on each side, then screw the shelf to the cleats, fastening into the wood in both cases. Select a wood species that is similar to the veneer of the bookcases, or a species that stains well (poplar comes to mind) and do your best to match at least the tone of the wood; and cut the front of the cleat at a slant back to make it less prominent.

In my opinion, no one should ever make a bookcase of that design - that is, without a face frame - without a fixed center shelf to prevent bowing.

Once that's done, inspect the existing shelves to ensure that the slots aren't breaking out. And don't get carried away with the loads on the shelves. The load is being supported by the particleboard between the slot and the top of the shelf, so maybe 3/8" of particleboard. Not much strength there.

Re: How to compress bulging bookcases?

#5

Re: How to compress bulging bookcases?

ian in Sydney

what I've done with similar store bought book shelves is

1. screw the uprights together -- usually either in line with a shelf, or far enough back from the front edge that teh countersunk screws are hidden by books :)

2. after 25 years, I doubt that the shelf layout will change, so all the shelves could be secured to the uprights with long particle board screws

Re: How to compress bulging bookcases?

#6

25 years out of a cheap bookcase?!

Joanne in Point Pleasant, PA

My remedy would be to build a new bookcase out of plywood edged in hardwood with some permanent shelves (edged in hardwood) in dadoes and some adjustable shelves with shelf pins.

Re: How to compress bulging bookcases?

#7

Amen.


Re: How to compress bulging bookcases?

#8

Re: 25 years out of a cheap bookcase?!

Barry Irby

I understand, but my Packrat gene kicked in I could not bring myself to destroy a book case I had used for 25 years, even if it was particle board to start with. I might run a threaded rod through it from one side to the other to hold it together. Maybe two, and route a slot in the bottom of a middle shelf to conceal them.

Re: How to compress bulging bookcases?

#9

Re: How to compress bulging bookcases?

E Snow

The easiest and likely cleanest solution at this point will be a k.d. fastener. I would recommend a rafix. Since you have had 25 years to settle on where the shelves go this semi-permanent solution is pretty ideal. Likely the shelf support wire is already bored at 5 mm which is what the rafix shoulder stud needs for placement. You may need to epoxy putty the holes and rebore at 5mm if they are too loose. May have to glue in a fill for the dado for the shelf wire, could be chewed from the fall but really won't matter since they have a shoulder to rest on. Call that optional. Two per side on one or two shelves will draw it all together again. SOP for commercially sold book cases going on forever now. Should buy you another 25 years.

Ebay is a fair source for small quantities. Saw quite a few there just now. (search Hafele Rafix SE Ridgid #263.15.705 Zinc Nickel Plated 19 mm)

Should only need a drill press for the install, may have to buy a 20mm forstner bit, again ebay.

Re: How to compress bulging bookcases?

#10

kwcrva@gmail.com

Brint in Richmond, VA


After the top shelf on this bookcase fell down for the third time in a year, I took a closer look and discovered that the case sides had begun bulging outward.


In all fairness, these bookcases have served me very well for over 25 years, especially considering that they're made of veneered particleboard.

Each shelf has a groove cut into each end, which fits over removable wire supports that stick into pre-drilled holes in the case sides.



In bulging outward, the sides have pulled the wire supports out far enough from the grooved shelf-ends so that they lose their purchase and the shelf falls.

Regrettably, there is no fixed center shelf to keep the case sides together; if there were, then I likely wouldn't be having this problem. That said, I'm leery of trying to glue or screw in the center shelf now as a way of bringing the sides back in, simply because I'm working with 25-year-old particleboard all around and I'm not confident of its holding power.

In my dreams, I simply affix a 12' invisible pipe clamp to the center back of the three bookcases and squeeze them together. In reality, the only immediate solution I see is to fashion myself some new wire supports that extend farther in (toward the shelf grooves) from the case sides than the current ones - but then I'm afraid the sides will continue their bulging journey outward.

Does anyone's experience with particleboard suggest that fixing the center shelf might actually work? The shelves are 30" x 11-1/2" x 5/8". Thanks to anyone who can offer a suggested remedy.

Re: How to compress bulging bookcases?

#11

Re: How to compress bulging bookcases?

D. Brown

I could never bring myself to trust particleboard to hold any kind of hardware. I think the simplest solution would be to take out the middle shelves out of each unit, rip out a 2" section out of the middle, glue a length of hardwood in the middle, and screw the shelves into the sides with big washers or mending plates on the outside of the cases (in order to spread out the force over as much surface area as possible).