Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Half round table... *PICS*

Posts

Half round table... *PICS*

#1

Half round table... *PICS*

Joe in a Cleveland suburb

Thanks as always everybody for the replies and feedback in the previous thread.

Ellis said:

"I'm curious as to how you will add the rear apron at this point. Sliding dovetails?"

I am stealing an idea from a FWW book I have and will be dovetailing the back apron into place.

Bill T. said:

"I think 3/16" may be too thick for the bead."

You can see in the picture below, I've made them 3/16" and stuck them on with tape to see if I like it or not. Haven'r decided for sure.

Bill T. said:

"One must never do chemistry experiments"

I did lots of chemistry experiments in the backyard when I was a kid. Sure wish I had some of those G.I. Joe's I melted and/or burned up with my experiments...

Bill T. said:

"he commented that he dislikes the modern trend of mixing wood species in the main parts of a construction"

I've been wanting to make a small table for a long time with a Cherry base and Curly maple top after seeing some Shaker pieces with those two woods. However, after what you said, and placing different pieces of wood on top of the table, I am starting to re-think it. My wife agrees too. So I might end up using Cherry for the top. Haven't really decided on that yet either. But I am leaning towards Cherry now for the top.

Regarding the hide glue. I've been heating up my own for a while now and never had a problem. I actually like using it. I think in this case the cold was working against me, inexperience, and the more I think about it, it may not have been 'liquidy' enough. Live and learn.

Regarding the vise... I think that one would be overkill for me. I've been wanting to make a nice workbench since Christopher Schwarz brought them into vogue (that's not a knock on Mr. Schwarz - I like his stuff). I will need to build one for a left though.

Last night I finished shaping the beading. Currently they are 3/16" thick. I stuck them on with double sided tape to see if I like it. Not sure if I will go thinner or not. Wife says she likes it as is.

Beading stuck on:


A little bit closer look:


The shop dogs like it!



Barkley and Pebbles

Re: Half round table... *PICS*

#2

Re: Half round table... *PICS*

Keith Newton

Looking good Joe, I liked that last shot. Sassafras walked up trying to steal my napkin just as I got to that one. She is a Golden girl too, and gave them a friendly look. But then, she has never met another dog or person that she didn't want to be friends with. ha

Re: Half round table... *PICS*

#3

Re: Half round table... *PICS*

roger lance

Joe.....regarding the bead, I agree with your wife (which is something a smart ww will always tend to do as it helps gain her support when you want to buy another expensive tool).....the bead looks good.....and if she prefers a cherry top, well.....

Re: Half round table... *PICS*

#4

Re: Half round table... *PICS*

Thomas Skaggs, Foothills of Mount Level

I think the bead is within bounds. It's a tad generous, but looks good to my eye. Nice looking project by the way. And Bernie agrees!


Re: Half round table... *PICS*

#5

Another vote for the bead size

Bill Houghton, Sebastopol, CA

I think the thicker bead looks better than a thinner one would.

Re: Half round table... *PICS*

#6

A rigged election

Bill Tindall, E.Tn.

We only have information on one candidate.

For what it is worth my first cock bead was thicker than the second which in turn was thicker than the third....after which thickness stabilized. Somewhere in this journey I started noticing what others had done on Period furniture.

I found that a thinner bead made the piece more formal looking.

BTW, so your dogs eat sand paper? When I had a dog she would come to the shop and either gnaw a piece of wood or if she could find it, a scrap of sand paper was as good as a ripe bone. I supposed it was the glue, which was another reason to not risk hide glue on the furniture.

Re: Half round table... *PICS*

#7

Re: Half round table... *PICS*

Barry Irby

I would go to the 1/8" bead and I would try it with a very small (1/32 or 1/64") rabbet between the rail and the bead. If the bead is proud of the rail you don't need the rabbet, but if it is flush it may improve the look.

At least let you wife look at it that way. We all know that's the only vote that matters to a smart man.

Re: Half round table... *PICS*

#8

Re: Half round table... *PICS*

David Yoho

Joe, I've been following this project from the start. On the issue of the top - I'm guessing you planned to use the maple with only a clear finish. As the cherry will quickly darken with exposure to sun light, the maple will not but I don't think it would look that bad. However, if you went with cherry for the top, you might look for a piece with figure.

That said, there is a way to use the curly maple where it will look like cherry. I have a recipe down in my shop that uses Lockwood dyes for a cherry finish. I used it on a jewelry armoire where the case was cherry and the drawer fronts were tiger maple. Once the cherry darkened it was a great match. Below is a shot just after it was built to give you an idea. So, you could actually use that beautiful maple in the pictures if you wanted to.

Re: Half round table... *PICS*

#9

Mixing woods... and the bead...

John in NM

Hey Joe, it's looking great!

While I tend to agree about mixing woods, I don't mind doing it with maple and cherry. They are enough of a similar hue to my eye that the effect is not jarring, as it tends to be with maple and walnut or the like.

Especially making the top from a nicely figured and lighter color wood rather than the other way around could work fine.

But the sure thing is to make the top from cherry too. You'll never go wrong doing that.

Come to think of it, I made the vanity for my wife's bath from red oak (since we had it on hand), but made the door panels and drawer fronts from mesquite. The oak with an oil finish was just dark enough to work. Maple would have been a bit too light in color for that I think. Kind of ties in with the maple/cherry comments - I find it to be more about the hue than anything else.

The other thing I will say also ties in a bit. To my eye, the bead looks fine, because it is also cherry. If I were using a contrasting bead I would make it thinner, 1/8" I don't think I have a picture, but I did that once with mahogany and rosewood.

Re: Half round table... *PICS*

#10

Re: Half round table... *PICS*

Joe in a Cleveland suburb

Thanks David.

I think I am going with a cherry top. I am interested in the recipe you mentioned though. I'd like to try it and see how it looks.

Thank you.

Re: Half round table... *PICS*

#11

Re: Half round table... *PICS*

Tony - Memphis

Looking good! Hey, looking at that piece of maple in the background...I don't care what you stick THAT on, it will look darn nice!

I did something similar when I built my round table. I tried a couple of different sizes of beads. I went with 1/8 I think. One conisderation I had was the length of the square portion of the legs. I made mine in poplar and dyed them "ebony." I did that to tie in with the black inlay and the the black "socks" on the legs.

Tony

This is before I stained anything...the blck dots were for evaluating the "right" size for the center ebony inlay.

Re: Half round table... *PICS*

#12

Darn you guys!

John in NM

Now I want to build some small tables! I'm too busy!!!

I hope no one posts pics of an half elliptical console table, I'd be sunk! :D

(Nice job to both Joe and Tony :D )

Re: Half round table... *PICS*

#13

Re: Half round table... *PICS*

joe in a Cleveland suburb

Wow. That's looks pretty awesome. Puts my little table to shame. Well, half shame since mine is only half a table... :)